[PATCH v2 4/4] riscv: dts: spacemit: Update PMIC supply properties for BPI-F3 and Jupiter

[Alex Elder]

On 1/23/26 6:20 PM, Guodong Xu wrote:
> Update individual supply properties in pmic "spacemit,p1" node to specify
> the board's power tree topology for BananaPi F3 and Milk-V Jupiter.
> 
> Previously these relationships were hardcoded in the driver; now they
> are explicitly defined in the devicetree per the updated binding
> document spacemit,p1.yaml.
> 
> Signed-off-by: Guodong Xu <guodong at riscstar.com>

I acknowledge that you've made an ABI change, and I should
have done a better job of describing this the first time
around.  (And reviewers might have caught that!)

I had some of the same thoughts about supporting just
"vin_supply" for older systems.

However I agree with the conclusion you and Vivian
came to, which is that practically speaking it isn't
likely to be a problem.  Boards should use either
old DTB and software or new DTB and software, not
a mix.

Reviewed-by: Alex Elder <elder at riscstar.com>


> ---
> v2: Added the pmic supply properties for K1 Milkv Jupiter.
>      Updated the commit message accordingly.
> ---
>   arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts   | 12 ++++++++++--
>   arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts | 12 ++++++++++--
>   2 files changed, 20 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
> index 5971605754b3..444c3b1e6f44 100644
> --- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
> +++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
> @@ -190,7 +190,15 @@ pmic at 41 {
>   		compatible = "spacemit,p1";
>   		reg = <0x41>;
>   		interrupts = <64>;
> -		vin-supply = <&reg_vcc_4v>;
> +		vin1-supply = <&reg_vcc_4v>;
> +		vin2-supply = <&reg_vcc_4v>;
> +		vin3-supply = <&reg_vcc_4v>;
> +		vin4-supply = <&reg_vcc_4v>;
> +		vin5-supply = <&reg_vcc_4v>;
> +		vin6-supply = <&reg_vcc_4v>;
> +		aldoin-supply = <&reg_vcc_4v>;
> +		dldoin1-supply = <&buck5>;
> +		dldoin2-supply = <&buck5>;
>   
>   		regulators {
>   			buck1 {
> @@ -221,7 +229,7 @@ buck4 {
>   				regulator-always-on;
>   			};
>   
> -			buck5 {
> +			buck5: buck5 {
>   				regulator-min-microvolt = <500000>;
>   				regulator-max-microvolt = <3450000>;
>   				regulator-ramp-delay = <5000>;
> diff --git a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
> index 800a112d5d70..e2702a781734 100644
> --- a/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
> +++ b/arch/riscv/boot/dts/spacemit/k1-milkv-jupiter.dts
> @@ -100,7 +100,15 @@ pmic at 41 {
>   		compatible = "spacemit,p1";
>   		reg = <0x41>;
>   		interrupts = <64>;
> -		vin-supply = <&reg_vcc_4v>;
> +		vin1-supply = <&reg_vcc_4v>;
> +		vin2-supply = <&reg_vcc_4v>;
> +		vin3-supply = <&reg_vcc_4v>;
> +		vin4-supply = <&reg_vcc_4v>;
> +		vin5-supply = <&reg_vcc_4v>;
> +		vin6-supply = <&reg_vcc_4v>;
> +		aldoin-supply = <&reg_vcc_4v>;
> +		dldoin1-supply = <&buck5>;
> +		dldoin2-supply = <&buck5>;
>   
>   		regulators {
>   			buck1 {
> @@ -131,7 +139,7 @@ buck4 {
>   				regulator-always-on;
>   			};
>   
> -			buck5 {
> +			buck5: buck5 {
>   				regulator-min-microvolt = <500000>;
>   				regulator-max-microvolt = <3450000>;
>   				regulator-ramp-delay = <5000>;
>