[PATCH v3 1/5] riscv: dts: spacemit: k3: move USB3 phy to board level

[Inochi Amaoto]

On Wed, Aug 19, 2026 at 06:15:42PM +0200, Aurelien Jarno wrote:
> On the SpacemiT K3 SoC, the combo phy provides 8 lines that can
> either be used for PCIe or USB3, depending on its configuration
> (spacemit,apmu). This configuration is defined at the board level, and
> assigning a phy line to a USB3 controller while it is configured as PCIe
> results in an "Invalid PHY mode" error.
> 
> Move the USB3 phy at the board level, the as it is done for the
> submitted PCIe controller [1]. Keep the USB2 phy at the SoC level as
> there is one phy per USB controller.
> 
> [1] https://lore.kernel.org/20260727094726.890179-3-inochiama@gmail.com/
> 
> Fixes: 46380e4b1534c1626cecd7f4d0abb5e0cce09af6 ("riscv: dts: spacemit: k3: add USB controller and USB phy support")
> Cc: Inochi Amaoto <inochiama at gmail.com>
> Signed-off-by: Aurelien Jarno <aurelien at aurel32.net>
> ---
>  arch/riscv/boot/dts/spacemit/k3-pico-itx.dts | 3 +++
>  arch/riscv/boot/dts/spacemit/k3.dtsi         | 5 ++---
>  2 files changed, 5 insertions(+), 3 deletions(-)
> 
> diff --git a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> index b084a35aa00e..171bd2f40aa6 100644
> --- a/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> +++ b/arch/riscv/boot/dts/spacemit/k3-pico-itx.dts
> @@ -328,5 +328,8 @@ &usb3d_u2phy {
>  };
>  
>  &usb3d {
> +	phys = <&usb3d_u2phy>,
> +	       <&combophy 4 PHY_TYPE_USB3>;
> +	phy-names = "usb2-phy", "usb3-phy";
>  	status = "okay";
>  };
> diff --git a/arch/riscv/boot/dts/spacemit/k3.dtsi b/arch/riscv/boot/dts/spacemit/k3.dtsi
> index c3f2dce0969c..3e24054d2084 100644
> --- a/arch/riscv/boot/dts/spacemit/k3.dtsi
> +++ b/arch/riscv/boot/dts/spacemit/k3.dtsi
> @@ -452,9 +452,8 @@ usb3d: usb at 81a00000 {
>  				 <&syscon_apmu RESET_APMU_USB3_D_VCC>,
>  				 <&syscon_apmu RESET_APMU_USB3_D_PHY>;
>  			reset-names = "ahb", "vcc", "phy";

> -			phys = <&usb3d_u2phy>,
> -			       <&combophy 4 PHY_TYPE_USB3>;
> -			phy-names = "usb2-phy", "usb3-phy";
> +			phys = <&usb3d_u2phy>;
> +			phy-names = "usb2-phy";

I suggest removing this completely as we can not determine the
phy we used. I think it is suitable for setting this in board
file only

Regards,
Inochi

>  			phy_type = "utmi";
>  			snps,dis_enblslpm_quirk;
>  			snps,dis_u2_susphy_quirk;
> -- 
> 2.53.0
> 
> 
> _______________________________________________
> linux-riscv mailing list
> linux-riscv at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv