[PATCH v8 3/3] riscv: dts: spacemit: define a SPI controller node

[Guodong Xu]

From: Alex Elder <elder at riscstar.com>

Define a node for the fourth SoC SPI controller (number 3) on the
SpacemiT K1 SoC.

Enable it on the Banana Pi BPI-F3 board, which exposes this feature
via its GPIO block:
  GPIO PIN 19:  MOSI
  GPIO PIN 21:  MISO
  GPIO PIN 23:  SCLK
  GPIO PIN 24:  SS (inverted)

Define pincontrol configurations for the pins as used on that board.

(This was tested using a GigaDevice GD25Q64E SPI NOR chip.)

Reviewed-by: Yixun Lan <dlan at gentoo.org>
Signed-off-by: Alex Elder <elder at riscstar.com>
Signed-off-by: Guodong Xu <guodong at riscstar.com>
---
 arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts |  7 +++++++
 arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi    | 20 ++++++++++++++++++++
 arch/riscv/boot/dts/spacemit/k1.dtsi            | 15 +++++++++++++++
 3 files changed, 42 insertions(+)

diff --git a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
index 5971605754b35..61b93765f42cf 100644
--- a/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
+++ b/arch/riscv/boot/dts/spacemit/k1-bananapi-f3.dts
@@ -14,6 +14,7 @@ aliases {
 		ethernet0 = &eth0;
 		ethernet1 = &eth1;
 		serial0 = &uart0;
+		spi3 = &spi3;
 		i2c2 = &i2c2;
 		i2c8 = &i2c8;
 	};
@@ -327,6 +328,12 @@ &pcie2 {
 	status = "okay";
 };
 
+&spi3 {
+	pinctrl-0 = <&ssp3_0_cfg>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
 &uart0 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&uart0_2_cfg>;
diff --git a/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi b/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
index b13dcb10f4d66..34d88334e95e4 100644
--- a/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k1-pinctrl.dtsi
@@ -570,4 +570,24 @@ pwm14-1-pins {
 			drive-strength = <32>;
 		};
 	};
+
+	ssp3_0_cfg: ssp3-0-cfg {
+		ssp3-0-pins {
+			pinmux = <K1_PADCONF(75, 2)>,	/* SCLK */
+				 <K1_PADCONF(77, 2)>,	/* MOSI  */
+				 <K1_PADCONF(78, 2)>;	/* MISO */
+
+			bias-disable;
+			drive-strength = <19>;
+			power-source = <3300>;
+		};
+
+		ssp3-0-frm-pins {
+			pinmux = <K1_PADCONF(76, 2)>;	/* FRM (frame) */
+
+			bias-pull-up = <0>;
+			drive-strength = <19>;
+			power-source = <3300>;
+		};
+	};
 };
diff --git a/arch/riscv/boot/dts/spacemit/k1.dtsi b/arch/riscv/boot/dts/spacemit/k1.dtsi
index 529ec68e9c23e..1ecb09e58042f 100644
--- a/arch/riscv/boot/dts/spacemit/k1.dtsi
+++ b/arch/riscv/boot/dts/spacemit/k1.dtsi
@@ -983,6 +983,21 @@ qspi: spi at d420c000 {
 				status = "disabled";
 			};
 
+			spi3: spi at d401c000 {
+				compatible = "spacemit,k1-spi";
+				reg = <0x0 0xd401c000 0x0 0x30>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+				clocks = <&syscon_apbc CLK_SSP3>,
+					 <&syscon_apbc CLK_SSP3_BUS>;
+				clock-names = "core", "bus";
+				resets = <&syscon_apbc RESET_SSP3>;
+				interrupts = <55>;
+				dmas = <&pdma 20>, <&pdma 19>;
+				dma-names = "rx", "tx";
+				status = "disabled";
+			};
+
 			/* sec_uart1: 0xf0612000, not available from Linux */
 		};
 

-- 
2.43.0