[PATCH v5 3/3] riscv: dts: spacemit: Enable USB3.0/PCIe on OrangePi RV2

[Yixun Lan]

Hi Han, 

On 00:54 Fri 03 Apr     , Han Gao wrote:
> Enable the DWC3 USB 3.0 controller and its associated usbphy2 on the
> OrangePi RV2 board.
> 
> The board utilizes a Genesys Logic GL3523 USB3.0 hub.
> 
> Define a 3.3v fixed voltage regulator for PCIe and enable PCIe and
> PHY-related Device Tree nodes for the OrangePi RV2.
> 
> Co-developed-by: Chukun Pan <amadeus at jmu.edu.cn>
> Signed-off-by: Chukun Pan <amadeus at jmu.edu.cn>
> Signed-off-by: Han Gao <gaohan at iscas.ac.cn>
> ---
>  .../boot/dts/spacemit/k1-orangepi-rv2.dts     | 80 +++++++++++++++++++
>  1 file changed, 80 insertions(+)
> 
> diff --git a/arch/riscv/boot/dts/spacemit/k1-orangepi-rv2.dts b/arch/riscv/boot/dts/spacemit/k1-orangepi-rv2.dts
> index a6de3753b876..c19952e70c31 100644
> --- a/arch/riscv/boot/dts/spacemit/k1-orangepi-rv2.dts
> +++ b/arch/riscv/boot/dts/spacemit/k1-orangepi-rv2.dts
> @@ -23,6 +23,15 @@ chosen {
>  		stdout-path = "serial0";
>  	};
>  
> +	pcie_vcc_3v3: regulator-pcie-vcc3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "pcie_vcc3v3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		gpio = <&gpio K1_GPIO(116) GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
>  	vcc_5v0: regulator-vcc-5v0 {
>  		compatible = "regulator-fixed";
>  		regulator-name = "vcc_5v0";
> @@ -42,6 +51,16 @@ vcc4v0: regulator-vcc4v0 {
>  		vin-supply = <&vcc_5v0>;
>  	};
>  
> +	vcc5v0_usb30: regulator-vcc5v0-usb30 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc5v0_usb30";
> +		enable-active-high;
> +		gpios = <&gpio K1_GPIO(123) GPIO_ACTIVE_HIGH>;
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		vin-supply = <&vcc_5v0>;
> +	};
> +
>  	leds {
>  		compatible = "gpio-leds";
>  
> @@ -54,6 +73,10 @@ led1 {
>  	};
>  };
>  
> +&combo_phy {
> +	status = "okay";
> +};
> +
>  &eth0 {
>  	phy-handle = <&rgmii0>;
>  	phy-mode = "rgmii-id";
> @@ -200,8 +223,65 @@ dldo6 {
>  	};
>  };
>  
> +&pcie1_phy {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie1_3_cfg>;
> +	status = "okay";
> +};
> +
> +&pcie1_port {
> +	phys = <&pcie1_phy>;
> +	vpcie3v3-supply = <&pcie_vcc_3v3>;
> +};
> +
> +&pcie1 {
> +	vpcie3v3-supply = <&pcie_vcc_3v3>;
> +	status = "okay";
> +};
> +
> +&pcie2_phy {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pcie2_4_cfg>;
> +	status = "okay";
> +};
> +
> +&pcie2_port {
> +	phys = <&pcie2_phy>;
> +	vpcie3v3-supply = <&pcie_vcc_3v3>;
> +};
> +
> +&pcie2 {
> +	vpcie3v3-supply = <&pcie_vcc_3v3>;
> +	status = "okay";
> +};
> +
>  &uart0 {
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&uart0_2_cfg>;
>  	status = "okay";
>  };
> +
> +&usbphy2 {
> +	status = "okay";
> +};
> +
> +&usb_dwc3 {
> +	dr_mode = "host";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +	status = "okay";
Can you put vbus-supply here? see Chukun's patch
http://lore.kernel.org/r/20260402100007.110201-4-amadeus@jmu.edu.cn

> +
> +	hub_2_0: hub at 1 {
> +		compatible = "usb5e3,610";
> +		reg = <0x1>;
> +		peer-hub = <&hub_3_0>;
..
> +		vdd-supply = <&vcc5v0_usb30>;
I think the vdd is vcc_5v0, while vcc5v0_usb30 is the vbus, if we check
page 16 of RV2 schematics, GL3523-QFN75 (USB HUB)'s pin V5, VDDP directly
connect to VCC_5V0

> +	};
> +
> +	hub_3_0: hub at 2 {
> +		compatible = "usb5e3,620";
> +		reg = <0x2>;
> +		peer-hub = <&hub_2_0>;
> +		vdd-supply = <&vcc5v0_usb30>;
> +	};
> +};
> -- 
> 2.47.3
> 
> 

-- 
Yixun Lan (dlan)