[PATCH v3 0/4] riscv: dts: starfive: jh7110-common: Sync downstream U-Boot changes

[Emil Renner Berthing]

E Shattow wrote:
> U-Boot boot loader has adopted using the Linux dt-rebasing tree for dts
> with StarFive VisionFive2 board target (and related JH7110 common boards).
> Sync the minimum changes from jh7110-common.dtsi needed for boot so these
> can be dropped from U-Boot.
>
> Changes since v2:
>
> - 1/5 -> 1/4: Do not replace assigned CPU core or PLL0 clock when adding new
>   assignments. Adjust patch name and commit message accordingly.
> - 2/5 -> 2/4: Detail reason for qspi setting changes in commit message
> - 3/5 -> Drop uart0 clock-frequency patch
> - 4/5 -> 3/4: Add reviewed by tag (no change)
> - 5/5 -> 4/4: Follow dts coding style sort order. Add bootph-pre-ram hint
>   for mmc interfaces
>
> Note: mmc boot source modes of JH7110 loader on mask ROM are deprecated as
> of StarFive JH7110 User Guide 1.2 revision. The loader expects data within
> range of LBA 0 and LBA 1 in conflict with GUID Partition Table.
>
> SD Card and eMMC boot media are prepared as follows:
>
> # GPT partition SD Card or eMMC as
> # 1: Secondary Program Loader @ 0x200000
> # 2: Main payload area for use by SPL
> # 3: EFI System Partition
> sgdisk --clear \
>   --new=1:2M:+2M --typecode=1:2E54B353-1271-4842-806F-E436D6AF6985 \
>   --new=2:4M:+4M --typecode=2:5B193300-FC78-40CD-8002-E86C45580B47 \
>   --new=3:8M:+100M --typecode=3:EF00 /dev/sdX
>
> # Write offset value in bytes of loader 'backup section' SPL as part1 @ 2M
> python3 <<-EOF
> with open("/dev/sdX", "r+b") as f:
>   f.seek(0x0004)
>   f.write((0x200000).to_bytes(4, "little"))
> EOF
>
> # Write invalid CRC to trigger 'Main section boot fail,use backup section'
> python3 <<-EOF
> with open("/dev/sdX", "r+b") as f:
>   f.seek(0x0290)
>   f.write((0x5A5A5A5A).to_bytes(4, "little"))
> EOF

This series looks good to me now. Thank you.

/Emil

>
> E Shattow (4):
>   riscv: dts: starfive: jh7110-common: add CPU BUS PERH QSPI clocks to
>     syscrg
>   riscv: dts: starfive: jh7110-common: qspi flash setting read-delay 2
>     cycles max 100MHz
>   riscv: dts: starfive: jh7110-common: add eeprom node to i2c5
>   riscv: dts: starfive: jh7110-common: bootph-pre-ram hinting needed by
>     boot loader
>
>  .../boot/dts/starfive/jh7110-common.dtsi      | 31 ++++++++++++++++---
>  1 file changed, 27 insertions(+), 4 deletions(-)
>
>
> base-commit: ebd297a2affadb6f6f4d2e5d975c1eda18ac762d
> --
> 2.49.0
>
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv