[PATCH] riscv: dts: allwinner: d1: Add CPU thermal sensor and zone

[Alex Studer]

On 2/18/25 12:23 PM, Jernej Škrabec wrote:
> Dne torek, 18. februar 2025 ob 03:06:29 Srednjeevropski standardni čas je Alex Studer napisal(a):
>> The sun20i THS (built in CPU thermal sensor) is supported in code, but
>> was never added to the device tree. So, add it to the device tree,
>> along with a thermal zone for the CPU.
>>
>> Signed-off-by: Alex Studer <alex at studer.dev>
>> ---
>>  arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi | 31 +++++++++++++++++++
>>  .../boot/dts/allwinner/sunxi-d1s-t113.dtsi    | 16 ++++++++++
>>  2 files changed, 47 insertions(+)
>>
>> diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi b/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi
>> index 6367112e6..bdde82aa8 100644
>> --- a/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi
>> +++ b/arch/riscv/boot/dts/allwinner/sun20i-d1s.dtsi
>> @@ -3,6 +3,8 @@
>>  
>>  #define SOC_PERIPHERAL_IRQ(nr)	(nr + 16)
>>  
>> +#include <dt-bindings/thermal/thermal.h>
> Put above line on top (before SOC_PERIPHERAL_IRQ()).
Will fix in v2.
>> +
>>  #include "sunxi-d1s-t113.dtsi"
>>  
>>  / {
>> @@ -115,4 +117,33 @@ pmu {
>>  			<0x00000000 0x0000000e 0xffffffff 0xffffffff 0x00010000>,
>>  			<0x00000000 0x0000000f 0xffffffff 0xffffffff 0x00020000>;
>>  	};
>> +
>> +	thermal-zones {
>> +		cpu-thermal {
>> +			polling-delay-passive = <0>;
>> +			polling-delay = <0>;
>> +			thermal-sensors = <&ths>;
>> +
>> +			cooling-maps {
>> +				map0 {
>> +					trip = <&cpu_alert>;
>> +					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
>> +				};
>> +			};
>> +
>> +			trips {
>> +				cpu_alert: cpu-alert {
>> +					temperature = <85000>;
>> +					hysteresis = <2000>;
>> +					type = "passive";
>> +				};
>> +
>> +				cpu-crit {
>> +					temperature = <100000>;
>> +					hysteresis = <0>;
>> +					type = "critical";
>> +				};
> Where do those limits come from?
I took them from the definitions in
arch/arm64/boot/dts/allwinner/sun50i-h6.dtsi, which is what I generally
based this patch on. I checked the D1s datasheet and it does specify a
max "Ambient Operating Temperature" of 70 C and a max "Working Junction
Temperature Range" of 110 C. So I could use those, but the dtsi files
for the other sunxi chips don't seem to follow their respective
datasheets, so I wasn't sure what to do here.
>> +			};
>> +		};
>> +	};
>>  };
>> diff --git a/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi
>> index e4175adb0..fcfcaf06c 100644
>> --- a/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi
>> +++ b/arch/riscv/boot/dts/allwinner/sunxi-d1s-t113.dtsi
>> @@ -426,6 +426,10 @@ sid: efuse at 3006000 {
>>  			reg = <0x3006000 0x1000>;
>>  			#address-cells = <1>;
>>  			#size-cells = <1>;
>> +
>> +			ths_calibration: thermal-sensor-calibration at 14 {
>> +				reg = <0x14 0x8>;
>> +			};
>>  		};
>>  
>>  		crypto: crypto at 3040000 {
>> @@ -934,5 +938,17 @@ rtc: rtc at 7090000 {
>>  			clock-names = "bus", "hosc", "ahb";
>>  			#clock-cells = <1>;
>>  		};
>> +
>> +		ths: thermal-sensor at 2009400 {
>> +			compatible = "allwinner,sun20i-d1-ths";
>> +			reg = <0x2009400 0x100>;
> Size should be 0x400.
Will fix in v2.
>
> Best regards,
> Jernej

Thanks,
Alex

>
>> +			interrupts = <SOC_PERIPHERAL_IRQ(58) IRQ_TYPE_LEVEL_HIGH>;
>> +			clocks = <&ccu CLK_BUS_THS>;
>> +			clock-names = "bus";
>> +			resets = <&ccu RST_BUS_THS>;
>> +			nvmem-cells = <&ths_calibration>;
>> +			nvmem-cell-names = "calibration";
>> +			#thermal-sensor-cells = <0>;
>> +		};
>>  	};
>>  };
>>
>
>
>