[PATCH v2 3/3] riscv: dts: thead: Add TH1520 ethernet nodes

[Drew Fustini]

On Thu, Sep 26, 2024 at 09:30:32PM +0200, Andrew Lunn wrote:
> On Thu, Sep 26, 2024 at 12:13:06PM -0700, Drew Fustini wrote:
> > On Thu, Sep 26, 2024 at 08:39:29PM +0200, Andrew Lunn wrote:
> > > > +&mdio0 {
> > > > +	phy0: ethernet-phy at 1 {
> > > > +		reg = <1>;
> > > > +	};
> > > > +
> > > > +	phy1: ethernet-phy at 2 {
> > > > +		reg = <2>;
> > > > +	};
> > > > +};
> > > 
> > > Two PHYs on one bus...
> > 
> > Thanks for pointing this out. I will move phy1 to mdio1.
> 
> ???
> 
> Are you saying the two PHYs are not on the same bus?

Sorry, this is my first time working on an Ethernet driver and I
misunderstood.

Sipeed only shares the schematic of the baseboard for the LPi4a [1].
There are pages for GMAC Ethernet0 and GMAC Ethernet1. Each shows 4 MDIO
differential pairs going into a SG4301G transformer.

I believe that RTL8211F-CG phy chips are on the LM4A SoM board which
contains the TH1520 SoC. Unfortunately, Sipeed does not provide a
schematic of the SoM so its hard for me to inspect how the phy chips are
wired up.

Vendor kernel [2] that Sipeed uses has:

	mdio0 {
		#address-cells = <1>;
		#size-cells = <0>;
		compatible = "snps,dwmac-mdio";

		phy_88E1111_0: ethernet-phy at 0 {
			reg = <0x1>;
		};

		phy_88E1111_1: ethernet-phy at 1 {
			reg = <0x2>;
		};
	};

so I think that does mean they are on the same MDIO bus.

> 
> > > > +		gmac1: ethernet at ffe7060000 {
> > > > +			compatible = "thead,th1520-gmac", "snps,dwmac-3.70a";
> > > > +			reg = <0xff 0xe7060000 0x0 0x2000>, <0xff 0xec004000 0x0 0x1000>;
> > > > +			reg-names = "dwmac", "apb";
> > > > +			interrupts = <67 IRQ_TYPE_LEVEL_HIGH>;
> > > > +			interrupt-names = "macirq";
> > > > +			clocks = <&clk CLK_GMAC_AXI>, <&clk CLK_GMAC_AXI>;
> > > > +			clock-names = "stmmaceth", "pclk";
> > > > +			snps,pbl = <32>;
> > > > +			snps,fixed-burst;
> > > > +			snps,multicast-filter-bins = <64>;
> > > > +			snps,perfect-filter-entries = <32>;
> > > > +			snps,axi-config = <&stmmac_axi_config>;
> > > > +			status = "disabled";
> > > > +
> > > > +			mdio1: mdio {
> > > > +				compatible = "snps,dwmac-mdio";
> > > > +				#address-cells = <1>;
> > > > +				#size-cells = <0>;
> > > > +			};
> > > > +		};
> > > > +
> > > > +		gmac0: ethernet at ffe7070000 {
> > > > +			compatible = "thead,th1520-gmac", "snps,dwmac-3.70a";
> > > > +			reg = <0xff 0xe7070000 0x0 0x2000>, <0xff 0xec003000 0x0 0x1000>;
> > > > +			reg-names = "dwmac", "apb";
> > > > +			interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
> > > > +			interrupt-names = "macirq";
> > > > +			clocks = <&clk CLK_GMAC_AXI>, <&clk CLK_GMAC_AXI>;
> > > 
> > > And the MACs are listed in opposite order. Does gmac1 probe first,
> > > find the PHY does not exist, and return -EPROBE_DEFER. Then gmac0
> > > probes successfully, and then sometime later gmac1 then reprobes?
> > > 
> > > I know it is normal to list nodes in address order, but you might be
> > > able to avoid the EPROBE_DEFER if you reverse the order.
> > 
> > The probe order seems to always be the ethernet at ffe7060000 (gmac1) first
> > and then ethernet at ffe7070000 (gmac0). I do not see any probe deferral
> > in the boot log [1].
> 
> > [1] https://gist.github.com/pdp7/02a44b024bdb6be5fe61ac21303ab29a
> 
> So two PHYs are found, so they must be on the same bus.
> 
> It could well be that this MAC driver does not connect to the PHY
> until the interface is opened. That is a good 30 seconds after the
> driver probes in this log message. So there has been plenty of time
> for the PHYs to be found.
> 
> What would be interesting is if you used NFS root. Then the interface
> would be opened much faster, and you might see an EPROBE_DEFER. But
> i'm just speculating. If it works for you, there is no need to do
> more.
> 
>       Andrew

I tried to setup an nfs server with a rootfs on my local network. I can
mount it okay from my laptop so I think it is working okay. However, it
does not seem to work on the lpi4a [3]. It appears the rgmii-id
validation fails and the dwmac driver can not open the phy:

 thead-dwmac ffe7060000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0
 thead-dwmac ffe7060000.ethernet eth0: validation of rgmii-id with support \
             00,00000000,00000000,00006280 and advertisementa \
	     00,00000000,00000000,00006280 failed: -EINVAL
 thead-dwmac ffe7060000.ethernet eth0: __stmmac_open: Cannot attach to PHY (error: -22)

I suppose that this is what you were talking about that NFS will cause
the interface to be opened much faster.

Thanks,
Drew

[1] https://dl.sipeed.com/shareURL/LICHEE/licheepi4a/02_Schematic
[2] https://github.com/revyos/thead-kernel/blob/lpi4a/arch/riscv/boot/dts/thead/th1520-b-product.dts#L758
[3] https://gist.github.com/pdp7/458eb93509548383beabeb21c8ffc43a