[PATCH v2 3/3] riscv: dts: thead: Add TH1520 ethernet nodes
Drew Fustini
dfustini at tenstorrent.com
Thu Sep 26 11:15:52 PDT 2024
From: Emil Renner Berthing <emil.renner.berthing at canonical.com>
Signed-off-by: Emil Renner Berthing <emil.renner.berthing at canonical.com>
[drew: change apb registers from syscon to second reg of gmac node]
[drew: add phy reset delay properties for beaglev ahead]
Signed-off-by: Drew Fustini <dfustini at tenstorrent.com>
---
arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts | 91 ++++++++++++++
.../boot/dts/thead/th1520-lichee-module-4a.dtsi | 135 +++++++++++++++++++++
arch/riscv/boot/dts/thead/th1520.dtsi | 50 ++++++++
3 files changed, 276 insertions(+)
diff --git a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
index 5a5888f4eda6..ddcee6298939 100644
--- a/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
+++ b/arch/riscv/boot/dts/thead/th1520-beaglev-ahead.dts
@@ -15,6 +15,7 @@ / {
compatible = "beagle,beaglev-ahead", "thead,th1520";
aliases {
+ ethernet0 = &gmac0;
gpio0 = &gpio0;
gpio1 = &gpio1;
gpio2 = &gpio2;
@@ -108,6 +109,25 @@ &sdio0 {
status = "okay";
};
+&gmac0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_pins>;
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+};
+
+&mdio0 {
+ phy0: ethernet-phy at 1 {
+ reg = <1>;
+ interrupt-parent = <&gpio3>;
+ interrupts = <22 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio3 21 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <10000>;
+ reset-post-delay-us = <50000>;
+ };
+};
+
&padctrl_aosys {
led_pins: led-0 {
led-pins {
@@ -127,6 +147,77 @@ led-pins {
};
&padctrl0_apsys {
+ gmac0_pins: gmac0-0 {
+ tx-pins {
+ pins = "GMAC0_TX_CLK",
+ "GMAC0_TXEN",
+ "GMAC0_TXD0",
+ "GMAC0_TXD1",
+ "GMAC0_TXD2",
+ "GMAC0_TXD3";
+ function = "gmac0";
+ bias-disable;
+ drive-strength = <25>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ rx-pins {
+ pins = "GMAC0_RX_CLK",
+ "GMAC0_RXDV",
+ "GMAC0_RXD0",
+ "GMAC0_RXD1",
+ "GMAC0_RXD2",
+ "GMAC0_RXD3";
+ function = "gmac0";
+ bias-disable;
+ drive-strength = <1>;
+ input-enable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ mdc-pins {
+ pins = "GMAC0_MDC";
+ function = "gmac0";
+ bias-disable;
+ drive-strength = <13>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ mdio-pins {
+ pins = "GMAC0_MDIO";
+ function = "gmac0";
+ bias-disable;
+ drive-strength = <13>;
+ input-enable;
+ input-schmitt-enable;
+ slew-rate = <0>;
+ };
+
+ phy-reset-pins {
+ pins = "GMAC0_COL"; /* GPIO3_21 */
+ bias-disable;
+ drive-strength = <3>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ phy-interrupt-pins {
+ pins = "GMAC0_CRS"; /* GPIO3_22 */
+ function = "gpio";
+ bias-pull-up;
+ drive-strength = <1>;
+ input-enable;
+ input-schmitt-enable;
+ slew-rate = <0>;
+ };
+ };
+
uart0_pins: uart0-0 {
tx-pins {
pins = "UART0_TXD";
diff --git a/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi b/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
index ca84bc2039ef..d9d2e1f4dc68 100644
--- a/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
+++ b/arch/riscv/boot/dts/thead/th1520-lichee-module-4a.dtsi
@@ -11,6 +11,11 @@ / {
model = "Sipeed Lichee Module 4A";
compatible = "sipeed,lichee-module-4a", "thead,th1520";
+ aliases {
+ ethernet0 = &gmac0;
+ ethernet1 = &gmac1;
+ };
+
memory at 0 {
device_type = "memory";
reg = <0x0 0x00000000 0x2 0x00000000>;
@@ -25,6 +30,16 @@ &osc_32k {
clock-frequency = <32768>;
};
+&dmac0 {
+ status = "okay";
+};
+
+&aogpio {
+ gpio-line-names = "", "", "",
+ "GPIO00",
+ "GPIO04";
+};
+
&aonsys_clk {
clock-frequency = <73728000>;
};
@@ -55,6 +70,22 @@ &sdio0 {
status = "okay";
};
+&gmac0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac0_pins>, <&mdio0_pins>;
+ phy-handle = <&phy0>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+};
+
+&gmac1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&gmac1_pins>;
+ phy-handle = <&phy1>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+};
+
&gpio0 {
gpio-line-names = "", "", "", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "", "", "",
@@ -87,3 +118,107 @@ &gpio3 {
"GPIO09",
"GPIO10";
};
+
+&mdio0 {
+ phy0: ethernet-phy at 1 {
+ reg = <1>;
+ };
+
+ phy1: ethernet-phy at 2 {
+ reg = <2>;
+ };
+};
+
+&padctrl0_apsys {
+ gmac0_pins: gmac0-0 {
+ tx-pins {
+ pins = "GMAC0_TX_CLK",
+ "GMAC0_TXEN",
+ "GMAC0_TXD0",
+ "GMAC0_TXD1",
+ "GMAC0_TXD2",
+ "GMAC0_TXD3";
+ function = "gmac0";
+ bias-disable;
+ drive-strength = <25>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ rx-pins {
+ pins = "GMAC0_RX_CLK",
+ "GMAC0_RXDV",
+ "GMAC0_RXD0",
+ "GMAC0_RXD1",
+ "GMAC0_RXD2",
+ "GMAC0_RXD3";
+ function = "gmac0";
+ bias-disable;
+ drive-strength = <1>;
+ input-enable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+ };
+
+ gmac1_pins: gmac1-0 {
+ tx-pins {
+ pins = "GPIO2_18", /* GMAC1_TX_CLK */
+ "GPIO2_20", /* GMAC1_TXEN */
+ "GPIO2_21", /* GMAC1_TXD0 */
+ "GPIO2_22", /* GMAC1_TXD1 */
+ "GPIO2_23", /* GMAC1_TXD2 */
+ "GPIO2_24"; /* GMAC1_TXD3 */
+ function = "gmac1";
+ bias-disable;
+ drive-strength = <25>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ rx-pins {
+ pins = "GPIO2_19", /* GMAC1_RX_CLK */
+ "GPIO2_25", /* GMAC1_RXDV */
+ "GPIO2_30", /* GMAC1_RXD0 */
+ "GPIO2_31", /* GMAC1_RXD1 */
+ "GPIO3_0", /* GMAC1_RXD2 */
+ "GPIO3_1"; /* GMAC1_RXD3 */
+ function = "gmac1";
+ bias-disable;
+ drive-strength = <1>;
+ input-enable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+ };
+
+ mdio0_pins: mdio0-0 {
+ mdc-pins {
+ pins = "GMAC0_MDC";
+ function = "gmac0";
+ bias-disable;
+ drive-strength = <13>;
+ input-disable;
+ input-schmitt-disable;
+ slew-rate = <0>;
+ };
+
+ mdio-pins {
+ pins = "GMAC0_MDIO";
+ function = "gmac0";
+ bias-disable;
+ drive-strength = <13>;
+ input-enable;
+ input-schmitt-enable;
+ slew-rate = <0>;
+ };
+ };
+};
+
+&sdio0 {
+ bus-width = <4>;
+ max-frequency = <198000000>;
+ status = "okay";
+};
diff --git a/arch/riscv/boot/dts/thead/th1520.dtsi b/arch/riscv/boot/dts/thead/th1520.dtsi
index 517a9e2e93a3..f51cc0c465ee 100644
--- a/arch/riscv/boot/dts/thead/th1520.dtsi
+++ b/arch/riscv/boot/dts/thead/th1520.dtsi
@@ -222,6 +222,12 @@ aonsys_clk: aonsys-clk {
#clock-cells = <0>;
};
+ stmmac_axi_config: stmmac-axi-config {
+ snps,wr_osr_lmt = <15>;
+ snps,rd_osr_lmt = <15>;
+ snps,blen = <0 0 64 32 0 0 0>;
+ };
+
soc {
compatible = "simple-bus";
interrupt-parent = <&plic>;
@@ -273,6 +279,50 @@ uart0: serial at ffe7014000 {
status = "disabled";
};
+ gmac1: ethernet at ffe7060000 {
+ compatible = "thead,th1520-gmac", "snps,dwmac-3.70a";
+ reg = <0xff 0xe7060000 0x0 0x2000>, <0xff 0xec004000 0x0 0x1000>;
+ reg-names = "dwmac", "apb";
+ interrupts = <67 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ clocks = <&clk CLK_GMAC_AXI>, <&clk CLK_GMAC_AXI>;
+ clock-names = "stmmaceth", "pclk";
+ snps,pbl = <32>;
+ snps,fixed-burst;
+ snps,multicast-filter-bins = <64>;
+ snps,perfect-filter-entries = <32>;
+ snps,axi-config = <&stmmac_axi_config>;
+ status = "disabled";
+
+ mdio1: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ gmac0: ethernet at ffe7070000 {
+ compatible = "thead,th1520-gmac", "snps,dwmac-3.70a";
+ reg = <0xff 0xe7070000 0x0 0x2000>, <0xff 0xec003000 0x0 0x1000>;
+ reg-names = "dwmac", "apb";
+ interrupts = <66 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "macirq";
+ clocks = <&clk CLK_GMAC_AXI>, <&clk CLK_GMAC_AXI>;
+ clock-names = "stmmaceth", "pclk";
+ snps,pbl = <32>;
+ snps,fixed-burst;
+ snps,multicast-filter-bins = <64>;
+ snps,perfect-filter-entries = <32>;
+ snps,axi-config = <&stmmac_axi_config>;
+ status = "disabled";
+
+ mdio0: mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
emmc: mmc at ffe7080000 {
compatible = "thead,th1520-dwcmshc";
reg = <0xff 0xe7080000 0x0 0x10000>;
--
2.34.1
More information about the linux-riscv
mailing list