[PATCH 1/3] dt-bindings: gpio: spacemit: add support for K1 SoC

[Krzysztof Kozlowski]

On Wed, Sep 04, 2024 at 12:27:23AM +0000, Yixun Lan wrote:
> The GPIO controller of K1 support basic functions as input/output,
> all pins can be used as interrupt which route to one IRQ line,
> trigger type can be select between rising edge, failing edge, or both.
> There are four GPIO banks, each consisting of 32 pins.
> 
> Signed-off-by: Yixun Lan <dlan at gentoo.org>
> ---
>  .../devicetree/bindings/gpio/spacemit,k1-gpio.yaml | 95 ++++++++++++++++++++++
>  1 file changed, 95 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/gpio/spacemit,k1-gpio.yaml b/Documentation/devicetree/bindings/gpio/spacemit,k1-gpio.yaml
> new file mode 100644
> index 0000000000000..db2e62fb452fd
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/spacemit,k1-gpio.yaml
> @@ -0,0 +1,95 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/gpio/spacemit,k1-gpio.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: SpacemiT K1 GPIO controller
> +
> +description: >

Drop >

> +  The controller's registers are organized as sets of eight 32-bit
> +  registers with each set controlling a bank of up to 32 pins.  A single
> +  interrupt is shared for all of the banks handled by the controller.
> +
> +maintainers:
> +  - Yixun Lan <dlan at gentoo.org>

Maintainers go before description. Use example-schema as template.

> +
> +properties:
> +  $nodename:
> +    pattern: '^gpio@[0-9a-f]+$'


No, why? Drop.

> +
> +  compatible:
> +    items:

and you can drop items as well.

> +      - const: spacemit,k1-gpio
> +
> +  reg:
> +    maxItems: 1
> +    description: >

Drop >. Everywhere.

> +      Define the base and range of the I/O address space containing
> +      the SpacemiT K1 GPIO controller registers

Redundant description, drop.

> +
> +  ranges: true
> +
> +  "#gpio-cells":
> +    const: 2
> +    description: >
> +      The first cell is the pin number (within the controller's
> +      pin space), and the second is used for the following:
> +      bit[0]: polarity (0 for active-high, 1 for active-low)

Rather refer to standard GPIO bindings header.

> +
> +  gpio-controller: true
> +
> +  gpio-ranges: true
> +
> +  interrupts:
> +    maxItems: 1
> +    description:
> +      The interrupt shared by all GPIO lines for this controller.
> +
> +  interrupt-names:
> +    items:
> +      - const: gpio_mux
> +
> +  "#interrupt-cells":
> +    const: 2
> +    description: |
> +      The first cell is the GPIO number, the second should specify
> +      flags.  The following subset of flags is supported:
> +      - bits[3:0] trigger type flags (no level trigger type support)
> +        1 = low-to-high edge triggered
> +        2 = high-to-low edge triggered
> +      Valid combinations are 1, 2, 3

Hm? No, you must use standard interrupt flags, not custom ones.

> +
> +  interrupt-controller: true
> +
> +required:
> +  - compatible
> +  - reg
> +  - gpio-controller
> +  - '#gpio-cells'
> +  - interrupts
> +  - interrupt-names
> +  - interrupt-controller
> +  - '#interrupt-cells'

Use consistent quotes. Either ' or ".

> +
> +additionalProperties: false

Best regards,
Krzysztof