[PATCH v5 2/7] iommu/riscv: Add RISC-V IOMMU platform device driver
Anup Patel
apatel at ventanamicro.com
Fri May 24 09:32:23 PDT 2024
On Thu, May 23, 2024 at 9:43 PM Tomasz Jeznach <tjeznach at rivosinc.com> wrote:
>
> On Fri, May 17, 2024 at 8:51 PM Anup Patel <apatel at ventanamicro.com> wrote:
> >
> > On Sat, May 18, 2024 at 1:11 AM Tomasz Jeznach <tjeznach at rivosinc.com> wrote:
> > >
> > > On Fri, May 17, 2024 at 9:28 AM Anup Patel <apatel at ventanamicro.com> wrote:
> > > >
> > > > Hi Tomasz,
> > > >
> > > > On Fri, May 17, 2024 at 9:16 PM Tomasz Jeznach <tjeznach at rivosinc.com> wrote:
> > > > >
> > > > > On Fri, May 17, 2024 at 12:22 AM Zong Li <zong.li at sifive.com> wrote:
> > > > > >
> > > > > > On Wed, May 15, 2024 at 2:17 AM Tomasz Jeznach <tjeznach at rivosinc.com> wrote:
> > > > > > >
> > > > > > > Introduce platform device driver for implementation of RISC-V IOMMU
> > > > > > > architected hardware.
> > > > > > >
> > > > > > > Hardware interface definition located in file iommu-bits.h is based on
> > > > > > > ratified RISC-V IOMMU Architecture Specification version 1.0.0.
> > > > > > >
> > > > > > > This patch implements platform device initialization, early check and
> > > > > > > configuration of the IOMMU interfaces and enables global pass-through
> > > > > > > address translation mode (iommu_mode == BARE), without registering
> > > > > > > hardware instance in the IOMMU subsystem.
> > > > > > >
> > > > > > > Link: https://github.com/riscv-non-isa/riscv-iommu
> > > > > > > Co-developed-by: Nick Kossifidis <mick at ics.forth.gr>
> > > > > > > Signed-off-by: Nick Kossifidis <mick at ics.forth.gr>
> > > > > > > Co-developed-by: Sebastien Boeuf <seb at rivosinc.com>
> > > > > > > Signed-off-by: Sebastien Boeuf <seb at rivosinc.com>
> > > > > > > Reviewed-by: Lu Baolu <baolu.lu at linux.intel.com>
> > > > > > > Signed-off-by: Tomasz Jeznach <tjeznach at rivosinc.com>
> > > > > > > ---
> > > > > > > MAINTAINERS | 1 +
> > > > > > > drivers/iommu/Kconfig | 1 +
> > > > > > > drivers/iommu/Makefile | 2 +-
> > > > > > > drivers/iommu/riscv/Kconfig | 15 +
> > > > > > > drivers/iommu/riscv/Makefile | 2 +
> > > > > > > drivers/iommu/riscv/iommu-bits.h | 707 +++++++++++++++++++++++++++
> > > > > > > drivers/iommu/riscv/iommu-platform.c | 92 ++++
> > > > > > > drivers/iommu/riscv/iommu.c | 99 ++++
> > > > > > > drivers/iommu/riscv/iommu.h | 62 +++
> > > > > > > 9 files changed, 980 insertions(+), 1 deletion(-)
> > > > > > > create mode 100644 drivers/iommu/riscv/Kconfig
> > > > > > > create mode 100644 drivers/iommu/riscv/Makefile
> > > > > > > create mode 100644 drivers/iommu/riscv/iommu-bits.h
> > > > > > > create mode 100644 drivers/iommu/riscv/iommu-platform.c
> > > > > > > create mode 100644 drivers/iommu/riscv/iommu.c
> > > > > > > create mode 100644 drivers/iommu/riscv/iommu.h
> > > > > > >
> > > > > > > diff --git a/MAINTAINERS b/MAINTAINERS
> > > > > > > index 7e090f878dc7..c0ef07031d01 100644
> > > > > > > --- a/MAINTAINERS
> > > > > > > +++ b/MAINTAINERS
> > > > > > > @@ -18963,6 +18963,7 @@ L: iommu at lists.linux.dev
> > > > > > > L: linux-riscv at lists.infradead.org
> > > > > > > S: Maintained
> > > > > > > F: Documentation/devicetree/bindings/iommu/riscv,iommu.yaml
> > > > > > > +F: drivers/iommu/riscv/
> > > > > > >
> > > > > > > RISC-V MICROCHIP FPGA SUPPORT
> > > > > > > M: Conor Dooley <conor.dooley at microchip.com>
> > > > > > > diff --git a/drivers/iommu/Kconfig b/drivers/iommu/Kconfig
> > > > > > > index c04584be3089..9359f07fe671 100644
> > > > > > > --- a/drivers/iommu/Kconfig
> > > > > > > +++ b/drivers/iommu/Kconfig
> > > > > > > @@ -195,6 +195,7 @@ config MSM_IOMMU
> > > > > > > source "drivers/iommu/amd/Kconfig"
> > > > > > > source "drivers/iommu/intel/Kconfig"
> > > > > > > source "drivers/iommu/iommufd/Kconfig"
> > > > > > > +source "drivers/iommu/riscv/Kconfig"
> > > > > > >
> > > > > > > config IRQ_REMAP
> > > > > > > bool "Support for Interrupt Remapping"
> > > > > > > diff --git a/drivers/iommu/Makefile b/drivers/iommu/Makefile
> > > > > > > index 542760d963ec..5e5a83c6c2aa 100644
> > > > > > > --- a/drivers/iommu/Makefile
> > > > > > > +++ b/drivers/iommu/Makefile
> > > > > > > @@ -1,5 +1,5 @@
> > > > > > > # SPDX-License-Identifier: GPL-2.0
> > > > > > > -obj-y += amd/ intel/ arm/ iommufd/
> > > > > > > +obj-y += amd/ intel/ arm/ iommufd/ riscv/
> > > > > > > obj-$(CONFIG_IOMMU_API) += iommu.o
> > > > > > > obj-$(CONFIG_IOMMU_API) += iommu-traces.o
> > > > > > > obj-$(CONFIG_IOMMU_API) += iommu-sysfs.o
> > > > > > > diff --git a/drivers/iommu/riscv/Kconfig b/drivers/iommu/riscv/Kconfig
> > > > > > > new file mode 100644
> > > > > > > index 000000000000..5dcc5c45aa50
> > > > > > > --- /dev/null
> > > > > > > +++ b/drivers/iommu/riscv/Kconfig
> > > > > > > @@ -0,0 +1,15 @@
> > > > > > > +# SPDX-License-Identifier: GPL-2.0-only
> > > > > > > +# RISC-V IOMMU support
> > > > > > > +
> > > > > > > +config RISCV_IOMMU
> > > > > > > + bool "RISC-V IOMMU Support"
> > > > > > > + depends on RISCV && 64BIT
> > > > > > > + default y
> > > > > > > + select IOMMU_API
> > > > > >
> > > > > > Hi Tomasz,
> > > > > > Could I know do we need to add RISCV dependency on CONFIG_IOMMU_DMA
> > > > > > due to the patch 'de9f8a91eb32 ("iommu/dma: Clean up Kconfig")'?
> > > > > >
> > > > >
> > > > > Hi Zong,
> > > > >
> > > > > Correct, This series will be followed with actual enablement of the
> > > > > iommu/riscv driver with the change to add IOMMU_DMA for RISCV arch,
> > > > > here is the change:
> > > >
> > > > I understand that this series is intended to be minimal but I suggest
> > > > expanding this series a bit more such that at least a basic EDU device
> > > > works along with MSIs from EDU device. This will give us a more
> > > > usable IOMMU driver sooner and also allow people to do more
> > > > testing.
> > > >
> > > > Subsequent series can add more features (such as IOMMU_DMA,
> > > > HPM, etc) incrementally.
> > > >
> > >
> > > Hi Anup,
> > >
> > > This series introduces a fundamental and practical IOMMU/RISC-V
> > > driver. It is fully testable on simulated, emulated, or real hardware
> > > implementations of the RISC-V architecture. Users can enable
> > > additional kernel configuration options, such as VFIO and IOMMU_DMA,
> > > to facilitate testing.
> >
> > In terms of features, what is fundamental and practical IOMMU
> > driver to you might not be for others.
> >
> > >
> > > The activation of IOMMU_DMA for the RISC-V architecture will be
> > > feasible once the core components achieve compatibility with the DMA
> > > subsystem, which unfortunately is currently not the case. Without
> > > IOMMU_DMA enabled, driver will recognize RISC-V IOMMU hardware,
> > > register itself in the IOMMU core subsystem, and will provide basic
> > > IDENTITY protection domains for connected devices.
> >
> > I am not asking for IOMMU_DMA feature instead I am asking for
> > supporting device MSIs in this series.
> >
>
> Ok. Makes sense.
> I've looked at the option to pull in / add small change to enable MSI
> bypass window for systems with IMSIC enabled. With that, MSIs will be
> supported, however without full interrupt remapping capabilities that
> could IOMMU provide. If that sounds as sufficient change I'll add it
> to this series.
Jason wants to keep this separate so I suggest sending out your
subsequent series based upon this series sooner.
>
> > >
> > > For those interested in testing this series (based on v6.9), with MSI
> > > support (riscv_aia_v17), I have provided a ready to use branch [1]
> > > with necessary fixes/workarounds included for convenience.
> > >
> > > [1] link: https://github.com/tjeznach/linux/tree/riscv_iommu_v5_aia_17
> >
> > Up-streaming the patches is much more useful compared to
> > sharing patches in private branches.
> >
> > It seems you already have subsequent patches so why not just
> > submit another series which depends on this series ?
> >
> > It is very easy to pull patches from mailing list using b4. Waiting
> > for this series to be merged before sending another series will
> > only delay having a usable driver in upstream. People send-out
> > multiple interdependent series all the time. Usually, it takes time
> > to review patches so it is generally better to have patches on the
> > list as soon as possible. This also allows others to test and
> > propose or send fixes on top.
> >
>
> Understood. Next set of features, re-based on this series will go out
> shortly, as the initial set of iommu/riscv changes seams to be in
> stable shape IMHO.
Thanks, that will be very helpful.
Regards,
Anup
>
>
> > Regards,
> > Anup
> >
>
> Best,
> - Tomasz
>
> > >
> > > Best regards,
> > > - Tomasz
> > >
> > >
> > > > Regards,
> > > > Anup
> > > >
> > > > >
> > > > > --- a/drivers/iommu/Kconfig
> > > > > +++ b/drivers/iommu/Kconfig
> > > > > @@ -150,7 +150,7 @@ config OF_IOMMU
> > > > >
> > > > > # IOMMU-agnostic DMA-mapping layer
> > > > > config IOMMU_DMA
> > > > > - def_bool ARM64 || X86 || S390
> > > > > + def_bool ARM64 || X86 || S390 || RISCV
> > > > > select DMA_OPS
> > > > > select IOMMU_API
> > > > > select IOMMU_IOVA
> > > > >
> > > > > Best regards,
> > > > > - Tomasz
> > > > >
> > > > > > > + help
> > > > > > > + Support for implementations of the RISC-V IOMMU architecture that
> > > > > > > + complements the RISC-V MMU capabilities, providing similar address
> > > > > > > + translation and protection functions for accesses from I/O devices.
> > > > > > > +
> > > > > > > + Say Y here if your SoC includes an IOMMU device implementing
> > > > > > > + the RISC-V IOMMU architecture.
> > > > > > > diff --git a/drivers/iommu/riscv/Makefile b/drivers/iommu/riscv/Makefile
> > > > > > > new file mode 100644
> > > > > > > index 000000000000..e4c189de58d3
> > > > > > > --- /dev/null
> > > > > > > +++ b/drivers/iommu/riscv/Makefile
> > > > > > > @@ -0,0 +1,2 @@
> > > > > > > +# SPDX-License-Identifier: GPL-2.0-only
> > > > > > > +obj-$(CONFIG_RISCV_IOMMU) += iommu.o iommu-platform.o
> > > > > > > diff --git a/drivers/iommu/riscv/iommu-bits.h b/drivers/iommu/riscv/iommu-bits.h
> > > > > > > new file mode 100644
> > > > > > > index 000000000000..48f795a0cd10
> > > > > > > --- /dev/null
> > > > > > > +++ b/drivers/iommu/riscv/iommu-bits.h
> > > > > > > @@ -0,0 +1,707 @@
> > > > > > > +/* SPDX-License-Identifier: GPL-2.0-only */
> > > > > > > +/*
> > > > > > > + * Copyright © 2022-2024 Rivos Inc.
> > > > > > > + * Copyright © 2023 FORTH-ICS/CARV
> > > > > > > + * Copyright © 2023 RISC-V IOMMU Task Group
> > > > > > > + *
> > > > > > > + * RISC-V IOMMU - Register Layout and Data Structures.
> > > > > > > + *
> > > > > > > + * Based on the 'RISC-V IOMMU Architecture Specification', Version 1.0
> > > > > > > + * Published at https://github.com/riscv-non-isa/riscv-iommu
> > > > > > > + *
> > > > > > > + */
> > > > > > > +
> > > > > > > +#ifndef _RISCV_IOMMU_BITS_H_
> > > > > > > +#define _RISCV_IOMMU_BITS_H_
> > > > > > > +
> > > > > > > +#include <linux/types.h>
> > > > > > > +#include <linux/bitfield.h>
> > > > > > > +#include <linux/bits.h>
> > > > > > > +
> > > > > > > +/*
> > > > > > > + * Chapter 5: Memory Mapped register interface
> > > > > > > + */
> > > > > > > +
> > > > > > > +/* Common field positions */
> > > > > > > +#define RISCV_IOMMU_PPN_FIELD GENMASK_ULL(53, 10)
> > > > > > > +#define RISCV_IOMMU_QUEUE_LOGSZ_FIELD GENMASK_ULL(4, 0)
> > > > > > > +#define RISCV_IOMMU_QUEUE_INDEX_FIELD GENMASK_ULL(31, 0)
> > > > > > > +#define RISCV_IOMMU_QUEUE_ENABLE BIT(0)
> > > > > > > +#define RISCV_IOMMU_QUEUE_INTR_ENABLE BIT(1)
> > > > > > > +#define RISCV_IOMMU_QUEUE_MEM_FAULT BIT(8)
> > > > > > > +#define RISCV_IOMMU_QUEUE_OVERFLOW BIT(9)
> > > > > > > +#define RISCV_IOMMU_QUEUE_ACTIVE BIT(16)
> > > > > > > +#define RISCV_IOMMU_QUEUE_BUSY BIT(17)
> > > > > > > +
> > > > > > > +#define RISCV_IOMMU_ATP_PPN_FIELD GENMASK_ULL(43, 0)
> > > > > > > +#define RISCV_IOMMU_ATP_MODE_FIELD GENMASK_ULL(63, 60)
> > > > > > > +
> > > > > > > +/* 5.3 IOMMU Capabilities (64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_CAP 0x0000
> > > > > > > +#define RISCV_IOMMU_CAP_VERSION GENMASK_ULL(7, 0)
> > > > > > > +#define RISCV_IOMMU_CAP_S_SV32 BIT_ULL(8)
> > > > > > > +#define RISCV_IOMMU_CAP_S_SV39 BIT_ULL(9)
> > > > > > > +#define RISCV_IOMMU_CAP_S_SV48 BIT_ULL(10)
> > > > > > > +#define RISCV_IOMMU_CAP_S_SV57 BIT_ULL(11)
> > > > > > > +#define RISCV_IOMMU_CAP_SVPBMT BIT_ULL(15)
> > > > > > > +#define RISCV_IOMMU_CAP_G_SV32 BIT_ULL(16)
> > > > > > > +#define RISCV_IOMMU_CAP_G_SV39 BIT_ULL(17)
> > > > > > > +#define RISCV_IOMMU_CAP_G_SV48 BIT_ULL(18)
> > > > > > > +#define RISCV_IOMMU_CAP_G_SV57 BIT_ULL(19)
> > > > > > > +#define RISCV_IOMMU_CAP_AMO_MRIF BIT_ULL(21)
> > > > > > > +#define RISCV_IOMMU_CAP_MSI_FLAT BIT_ULL(22)
> > > > > > > +#define RISCV_IOMMU_CAP_MSI_MRIF BIT_ULL(23)
> > > > > > > +#define RISCV_IOMMU_CAP_AMO_HWAD BIT_ULL(24)
> > > > > > > +#define RISCV_IOMMU_CAP_ATS BIT_ULL(25)
> > > > > > > +#define RISCV_IOMMU_CAP_T2GPA BIT_ULL(26)
> > > > > > > +#define RISCV_IOMMU_CAP_END BIT_ULL(27)
> > > > > > > +#define RISCV_IOMMU_CAP_IGS GENMASK_ULL(29, 28)
> > > > > > > +#define RISCV_IOMMU_CAP_HPM BIT_ULL(30)
> > > > > > > +#define RISCV_IOMMU_CAP_DBG BIT_ULL(31)
> > > > > > > +#define RISCV_IOMMU_CAP_PAS GENMASK_ULL(37, 32)
> > > > > > > +#define RISCV_IOMMU_CAP_PD8 BIT_ULL(38)
> > > > > > > +#define RISCV_IOMMU_CAP_PD17 BIT_ULL(39)
> > > > > > > +#define RISCV_IOMMU_CAP_PD20 BIT_ULL(40)
> > > > > > > +
> > > > > > > +#define RISCV_IOMMU_CAP_VERSION_VER_MASK 0xF0
> > > > > > > +#define RISCV_IOMMU_CAP_VERSION_REV_MASK 0x0F
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * enum riscv_iommu_igs_settings - Interrupt Generation Support Settings
> > > > > > > + * @RISCV_IOMMU_CAP_IGS_MSI: I/O MMU supports only MSI generation
> > > > > > > + * @RISCV_IOMMU_CAP_IGS_WSI: I/O MMU supports only Wired-Signaled interrupt
> > > > > > > + * @RISCV_IOMMU_CAP_IGS_BOTH: I/O MMU supports both MSI and WSI generation
> > > > > > > + * @RISCV_IOMMU_CAP_IGS_RSRV: Reserved for standard use
> > > > > > > + */
> > > > > > > +enum riscv_iommu_igs_settings {
> > > > > > > + RISCV_IOMMU_CAP_IGS_MSI = 0,
> > > > > > > + RISCV_IOMMU_CAP_IGS_WSI = 1,
> > > > > > > + RISCV_IOMMU_CAP_IGS_BOTH = 2,
> > > > > > > + RISCV_IOMMU_CAP_IGS_RSRV = 3
> > > > > > > +};
> > > > > > > +
> > > > > > > +/* 5.4 Features control register (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_FCTL 0x0008
> > > > > > > +#define RISCV_IOMMU_FCTL_BE BIT(0)
> > > > > > > +#define RISCV_IOMMU_FCTL_WSI BIT(1)
> > > > > > > +#define RISCV_IOMMU_FCTL_GXL BIT(2)
> > > > > > > +
> > > > > > > +/* 5.5 Device-directory-table pointer (64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_DDTP 0x0010
> > > > > > > +#define RISCV_IOMMU_DDTP_MODE GENMASK_ULL(3, 0)
> > > > > > > +#define RISCV_IOMMU_DDTP_BUSY BIT_ULL(4)
> > > > > > > +#define RISCV_IOMMU_DDTP_PPN RISCV_IOMMU_PPN_FIELD
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * enum riscv_iommu_ddtp_modes - I/O MMU translation modes
> > > > > > > + * @RISCV_IOMMU_DDTP_MODE_OFF: No inbound transactions allowed
> > > > > > > + * @RISCV_IOMMU_DDTP_MODE_BARE: Pass-through mode
> > > > > > > + * @RISCV_IOMMU_DDTP_MODE_1LVL: One-level DDT
> > > > > > > + * @RISCV_IOMMU_DDTP_MODE_2LVL: Two-level DDT
> > > > > > > + * @RISCV_IOMMU_DDTP_MODE_3LVL: Three-level DDT
> > > > > > > + * @RISCV_IOMMU_DDTP_MODE_MAX: Max value allowed by specification
> > > > > > > + */
> > > > > > > +enum riscv_iommu_ddtp_modes {
> > > > > > > + RISCV_IOMMU_DDTP_MODE_OFF = 0,
> > > > > > > + RISCV_IOMMU_DDTP_MODE_BARE = 1,
> > > > > > > + RISCV_IOMMU_DDTP_MODE_1LVL = 2,
> > > > > > > + RISCV_IOMMU_DDTP_MODE_2LVL = 3,
> > > > > > > + RISCV_IOMMU_DDTP_MODE_3LVL = 4,
> > > > > > > + RISCV_IOMMU_DDTP_MODE_MAX = 4
> > > > > > > +};
> > > > > > > +
> > > > > > > +/* 5.6 Command Queue Base (64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_CQB 0x0018
> > > > > > > +#define RISCV_IOMMU_CQB_ENTRIES RISCV_IOMMU_QUEUE_LOGSZ_FIELD
> > > > > > > +#define RISCV_IOMMU_CQB_PPN RISCV_IOMMU_PPN_FIELD
> > > > > > > +
> > > > > > > +/* 5.7 Command Queue head (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_CQH 0x0020
> > > > > > > +#define RISCV_IOMMU_CQH_INDEX RISCV_IOMMU_QUEUE_INDEX_FIELD
> > > > > > > +
> > > > > > > +/* 5.8 Command Queue tail (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_CQT 0x0024
> > > > > > > +#define RISCV_IOMMU_CQT_INDEX RISCV_IOMMU_QUEUE_INDEX_FIELD
> > > > > > > +
> > > > > > > +/* 5.9 Fault Queue Base (64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_FQB 0x0028
> > > > > > > +#define RISCV_IOMMU_FQB_ENTRIES RISCV_IOMMU_QUEUE_LOGSZ_FIELD
> > > > > > > +#define RISCV_IOMMU_FQB_PPN RISCV_IOMMU_PPN_FIELD
> > > > > > > +
> > > > > > > +/* 5.10 Fault Queue Head (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_FQH 0x0030
> > > > > > > +#define RISCV_IOMMU_FQH_INDEX RISCV_IOMMU_QUEUE_INDEX_FIELD
> > > > > > > +
> > > > > > > +/* 5.11 Fault Queue tail (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_FQT 0x0034
> > > > > > > +#define RISCV_IOMMU_FQT_INDEX RISCV_IOMMU_QUEUE_INDEX_FIELD
> > > > > > > +
> > > > > > > +/* 5.12 Page Request Queue base (64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_PQB 0x0038
> > > > > > > +#define RISCV_IOMMU_PQB_ENTRIES RISCV_IOMMU_QUEUE_LOGSZ_FIELD
> > > > > > > +#define RISCV_IOMMU_PQB_PPN RISCV_IOMMU_PPN_FIELD
> > > > > > > +
> > > > > > > +/* 5.13 Page Request Queue head (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_PQH 0x0040
> > > > > > > +#define RISCV_IOMMU_PQH_INDEX RISCV_IOMMU_QUEUE_INDEX_FIELD
> > > > > > > +
> > > > > > > +/* 5.14 Page Request Queue tail (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_PQT 0x0044
> > > > > > > +#define RISCV_IOMMU_PQT_INDEX_MASK RISCV_IOMMU_QUEUE_INDEX_FIELD
> > > > > > > +
> > > > > > > +/* 5.15 Command Queue CSR (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_CQCSR 0x0048
> > > > > > > +#define RISCV_IOMMU_CQCSR_CQEN RISCV_IOMMU_QUEUE_ENABLE
> > > > > > > +#define RISCV_IOMMU_CQCSR_CIE RISCV_IOMMU_QUEUE_INTR_ENABLE
> > > > > > > +#define RISCV_IOMMU_CQCSR_CQMF RISCV_IOMMU_QUEUE_MEM_FAULT
> > > > > > > +#define RISCV_IOMMU_CQCSR_CMD_TO BIT(9)
> > > > > > > +#define RISCV_IOMMU_CQCSR_CMD_ILL BIT(10)
> > > > > > > +#define RISCV_IOMMU_CQCSR_FENCE_W_IP BIT(11)
> > > > > > > +#define RISCV_IOMMU_CQCSR_CQON RISCV_IOMMU_QUEUE_ACTIVE
> > > > > > > +#define RISCV_IOMMU_CQCSR_BUSY RISCV_IOMMU_QUEUE_BUSY
> > > > > > > +
> > > > > > > +/* 5.16 Fault Queue CSR (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_FQCSR 0x004C
> > > > > > > +#define RISCV_IOMMU_FQCSR_FQEN RISCV_IOMMU_QUEUE_ENABLE
> > > > > > > +#define RISCV_IOMMU_FQCSR_FIE RISCV_IOMMU_QUEUE_INTR_ENABLE
> > > > > > > +#define RISCV_IOMMU_FQCSR_FQMF RISCV_IOMMU_QUEUE_MEM_FAULT
> > > > > > > +#define RISCV_IOMMU_FQCSR_FQOF RISCV_IOMMU_QUEUE_OVERFLOW
> > > > > > > +#define RISCV_IOMMU_FQCSR_FQON RISCV_IOMMU_QUEUE_ACTIVE
> > > > > > > +#define RISCV_IOMMU_FQCSR_BUSY RISCV_IOMMU_QUEUE_BUSY
> > > > > > > +
> > > > > > > +/* 5.17 Page Request Queue CSR (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_PQCSR 0x0050
> > > > > > > +#define RISCV_IOMMU_PQCSR_PQEN RISCV_IOMMU_QUEUE_ENABLE
> > > > > > > +#define RISCV_IOMMU_PQCSR_PIE RISCV_IOMMU_QUEUE_INTR_ENABLE
> > > > > > > +#define RISCV_IOMMU_PQCSR_PQMF RISCV_IOMMU_QUEUE_MEM_FAULT
> > > > > > > +#define RISCV_IOMMU_PQCSR_PQOF RISCV_IOMMU_QUEUE_OVERFLOW
> > > > > > > +#define RISCV_IOMMU_PQCSR_PQON RISCV_IOMMU_QUEUE_ACTIVE
> > > > > > > +#define RISCV_IOMMU_PQCSR_BUSY RISCV_IOMMU_QUEUE_BUSY
> > > > > > > +
> > > > > > > +/* 5.18 Interrupt Pending Status (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_IPSR 0x0054
> > > > > > > +
> > > > > > > +#define RISCV_IOMMU_INTR_CQ 0
> > > > > > > +#define RISCV_IOMMU_INTR_FQ 1
> > > > > > > +#define RISCV_IOMMU_INTR_PM 2
> > > > > > > +#define RISCV_IOMMU_INTR_PQ 3
> > > > > > > +#define RISCV_IOMMU_INTR_COUNT 4
> > > > > > > +
> > > > > > > +#define RISCV_IOMMU_IPSR_CIP BIT(RISCV_IOMMU_INTR_CQ)
> > > > > > > +#define RISCV_IOMMU_IPSR_FIP BIT(RISCV_IOMMU_INTR_FQ)
> > > > > > > +#define RISCV_IOMMU_IPSR_PMIP BIT(RISCV_IOMMU_INTR_PM)
> > > > > > > +#define RISCV_IOMMU_IPSR_PIP BIT(RISCV_IOMMU_INTR_PQ)
> > > > > > > +
> > > > > > > +/* 5.19 Performance monitoring counter overflow status (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_IOCOUNTOVF 0x0058
> > > > > > > +#define RISCV_IOMMU_IOCOUNTOVF_CY BIT(0)
> > > > > > > +#define RISCV_IOMMU_IOCOUNTOVF_HPM GENMASK_ULL(31, 1)
> > > > > > > +
> > > > > > > +/* 5.20 Performance monitoring counter inhibits (32bits) */
> > > > > > > +#define RISCV_IOMMU_REG_IOCOUNTINH 0x005C
> > > > > > > +#define RISCV_IOMMU_IOCOUNTINH_CY BIT(0)
> > > > > > > +#define RISCV_IOMMU_IOCOUNTINH_HPM GENMASK(31, 1)
> > > > > > > +
> > > > > > > +/* 5.21 Performance monitoring cycles counter (64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_IOHPMCYCLES 0x0060
> > > > > > > +#define RISCV_IOMMU_IOHPMCYCLES_COUNTER GENMASK_ULL(62, 0)
> > > > > > > +#define RISCV_IOMMU_IOHPMCYCLES_OVF BIT_ULL(63)
> > > > > > > +
> > > > > > > +/* 5.22 Performance monitoring event counters (31 * 64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_IOHPMCTR_BASE 0x0068
> > > > > > > +#define RISCV_IOMMU_REG_IOHPMCTR(_n) (RISCV_IOMMU_REG_IOHPMCTR_BASE + ((_n) * 0x8))
> > > > > > > +
> > > > > > > +/* 5.23 Performance monitoring event selectors (31 * 64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_IOHPMEVT_BASE 0x0160
> > > > > > > +#define RISCV_IOMMU_REG_IOHPMEVT(_n) (RISCV_IOMMU_REG_IOHPMEVT_BASE + ((_n) * 0x8))
> > > > > > > +#define RISCV_IOMMU_IOHPMEVT_CNT 31
> > > > > > > +#define RISCV_IOMMU_IOHPMEVT_EVENT_ID GENMASK_ULL(14, 0)
> > > > > > > +#define RISCV_IOMMU_IOHPMEVT_DMASK BIT_ULL(15)
> > > > > > > +#define RISCV_IOMMU_IOHPMEVT_PID_PSCID GENMASK_ULL(35, 16)
> > > > > > > +#define RISCV_IOMMU_IOHPMEVT_DID_GSCID GENMASK_ULL(59, 36)
> > > > > > > +#define RISCV_IOMMU_IOHPMEVT_PV_PSCV BIT_ULL(60)
> > > > > > > +#define RISCV_IOMMU_IOHPMEVT_DV_GSCV BIT_ULL(61)
> > > > > > > +#define RISCV_IOMMU_IOHPMEVT_IDT BIT_ULL(62)
> > > > > > > +#define RISCV_IOMMU_IOHPMEVT_OF BIT_ULL(63)
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * enum riscv_iommu_hpmevent_id - Performance-monitoring event identifier
> > > > > > > + *
> > > > > > > + * @RISCV_IOMMU_HPMEVENT_INVALID: Invalid event, do not count
> > > > > > > + * @RISCV_IOMMU_HPMEVENT_URQ: Untranslated requests
> > > > > > > + * @RISCV_IOMMU_HPMEVENT_TRQ: Translated requests
> > > > > > > + * @RISCV_IOMMU_HPMEVENT_ATS_RQ: ATS translation requests
> > > > > > > + * @RISCV_IOMMU_HPMEVENT_TLB_MISS: TLB misses
> > > > > > > + * @RISCV_IOMMU_HPMEVENT_DD_WALK: Device directory walks
> > > > > > > + * @RISCV_IOMMU_HPMEVENT_PD_WALK: Process directory walks
> > > > > > > + * @RISCV_IOMMU_HPMEVENT_S_VS_WALKS: S/VS-Stage page table walks
> > > > > > > + * @RISCV_IOMMU_HPMEVENT_G_WALKS: G-Stage page table walks
> > > > > > > + * @RISCV_IOMMU_HPMEVENT_MAX: Value to denote maximum Event IDs
> > > > > > > + */
> > > > > > > +enum riscv_iommu_hpmevent_id {
> > > > > > > + RISCV_IOMMU_HPMEVENT_INVALID = 0,
> > > > > > > + RISCV_IOMMU_HPMEVENT_URQ = 1,
> > > > > > > + RISCV_IOMMU_HPMEVENT_TRQ = 2,
> > > > > > > + RISCV_IOMMU_HPMEVENT_ATS_RQ = 3,
> > > > > > > + RISCV_IOMMU_HPMEVENT_TLB_MISS = 4,
> > > > > > > + RISCV_IOMMU_HPMEVENT_DD_WALK = 5,
> > > > > > > + RISCV_IOMMU_HPMEVENT_PD_WALK = 6,
> > > > > > > + RISCV_IOMMU_HPMEVENT_S_VS_WALKS = 7,
> > > > > > > + RISCV_IOMMU_HPMEVENT_G_WALKS = 8,
> > > > > > > + RISCV_IOMMU_HPMEVENT_MAX = 9
> > > > > > > +};
> > > > > > > +
> > > > > > > +/* 5.24 Translation request IOVA (64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_TR_REQ_IOVA 0x0258
> > > > > > > +#define RISCV_IOMMU_TR_REQ_IOVA_VPN GENMASK_ULL(63, 12)
> > > > > > > +
> > > > > > > +/* 5.25 Translation request control (64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_TR_REQ_CTL 0x0260
> > > > > > > +#define RISCV_IOMMU_TR_REQ_CTL_GO_BUSY BIT_ULL(0)
> > > > > > > +#define RISCV_IOMMU_TR_REQ_CTL_PRIV BIT_ULL(1)
> > > > > > > +#define RISCV_IOMMU_TR_REQ_CTL_EXE BIT_ULL(2)
> > > > > > > +#define RISCV_IOMMU_TR_REQ_CTL_NW BIT_ULL(3)
> > > > > > > +#define RISCV_IOMMU_TR_REQ_CTL_PID GENMASK_ULL(31, 12)
> > > > > > > +#define RISCV_IOMMU_TR_REQ_CTL_PV BIT_ULL(32)
> > > > > > > +#define RISCV_IOMMU_TR_REQ_CTL_DID GENMASK_ULL(63, 40)
> > > > > > > +
> > > > > > > +/* 5.26 Translation request response (64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_TR_RESPONSE 0x0268
> > > > > > > +#define RISCV_IOMMU_TR_RESPONSE_FAULT BIT_ULL(0)
> > > > > > > +#define RISCV_IOMMU_TR_RESPONSE_PBMT GENMASK_ULL(8, 7)
> > > > > > > +#define RISCV_IOMMU_TR_RESPONSE_SZ BIT_ULL(9)
> > > > > > > +#define RISCV_IOMMU_TR_RESPONSE_PPN RISCV_IOMMU_PPN_FIELD
> > > > > > > +
> > > > > > > +/* 5.27 Interrupt cause to vector (64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_ICVEC 0x02F8
> > > > > > > +#define RISCV_IOMMU_ICVEC_CIV GENMASK_ULL(3, 0)
> > > > > > > +#define RISCV_IOMMU_ICVEC_FIV GENMASK_ULL(7, 4)
> > > > > > > +#define RISCV_IOMMU_ICVEC_PMIV GENMASK_ULL(11, 8)
> > > > > > > +#define RISCV_IOMMU_ICVEC_PIV GENMASK_ULL(15, 12)
> > > > > > > +
> > > > > > > +/* 5.28 MSI Configuration table (32 * 64bits) */
> > > > > > > +#define RISCV_IOMMU_REG_MSI_CONFIG 0x0300
> > > > > > > +#define RISCV_IOMMU_REG_MSI_ADDR(_n) (RISCV_IOMMU_REG_MSI_CONFIG + ((_n) * 0x10))
> > > > > > > +#define RISCV_IOMMU_MSI_ADDR GENMASK_ULL(55, 2)
> > > > > > > +#define RISCV_IOMMU_REG_MSI_DATA(_n) (RISCV_IOMMU_REG_MSI_CONFIG + ((_n) * 0x10) + 0x08)
> > > > > > > +#define RISCV_IOMMU_MSI_DATA GENMASK_ULL(31, 0)
> > > > > > > +#define RISCV_IOMMU_REG_MSI_VEC_CTL(_n) (RISCV_IOMMU_REG_MSI_CONFIG + ((_n) * 0x10) + 0x0C)
> > > > > > > +#define RISCV_IOMMU_MSI_VEC_CTL_M BIT_ULL(0)
> > > > > > > +
> > > > > > > +#define RISCV_IOMMU_REG_SIZE 0x1000
> > > > > > > +
> > > > > > > +/*
> > > > > > > + * Chapter 2: Data structures
> > > > > > > + */
> > > > > > > +
> > > > > > > +/*
> > > > > > > + * Device Directory Table macros for non-leaf nodes
> > > > > > > + */
> > > > > > > +#define RISCV_IOMMU_DDTE_VALID BIT_ULL(0)
> > > > > > > +#define RISCV_IOMMU_DDTE_PPN RISCV_IOMMU_PPN_FIELD
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * struct riscv_iommu_dc - Device Context
> > > > > > > + * @tc: Translation Control
> > > > > > > + * @iohgatp: I/O Hypervisor guest address translation and protection
> > > > > > > + * (Second stage context)
> > > > > > > + * @ta: Translation Attributes
> > > > > > > + * @fsc: First stage context
> > > > > > > + * @msiptp: MSI page table pointer
> > > > > > > + * @msi_addr_mask: MSI address mask
> > > > > > > + * @msi_addr_pattern: MSI address pattern
> > > > > > > + * @_reserved: Reserved for future use, padding
> > > > > > > + *
> > > > > > > + * This structure is used for leaf nodes on the Device Directory Table,
> > > > > > > + * in case RISCV_IOMMU_CAP_MSI_FLAT is not set, the bottom 4 fields are
> > > > > > > + * not present and are skipped with pointer arithmetic to avoid
> > > > > > > + * casting, check out riscv_iommu_get_dc().
> > > > > > > + * See section 2.1 for more details
> > > > > > > + */
> > > > > > > +struct riscv_iommu_dc {
> > > > > > > + u64 tc;
> > > > > > > + u64 iohgatp;
> > > > > > > + u64 ta;
> > > > > > > + u64 fsc;
> > > > > > > + u64 msiptp;
> > > > > > > + u64 msi_addr_mask;
> > > > > > > + u64 msi_addr_pattern;
> > > > > > > + u64 _reserved;
> > > > > > > +};
> > > > > > > +
> > > > > > > +/* Translation control fields */
> > > > > > > +#define RISCV_IOMMU_DC_TC_V BIT_ULL(0)
> > > > > > > +#define RISCV_IOMMU_DC_TC_EN_ATS BIT_ULL(1)
> > > > > > > +#define RISCV_IOMMU_DC_TC_EN_PRI BIT_ULL(2)
> > > > > > > +#define RISCV_IOMMU_DC_TC_T2GPA BIT_ULL(3)
> > > > > > > +#define RISCV_IOMMU_DC_TC_DTF BIT_ULL(4)
> > > > > > > +#define RISCV_IOMMU_DC_TC_PDTV BIT_ULL(5)
> > > > > > > +#define RISCV_IOMMU_DC_TC_PRPR BIT_ULL(6)
> > > > > > > +#define RISCV_IOMMU_DC_TC_GADE BIT_ULL(7)
> > > > > > > +#define RISCV_IOMMU_DC_TC_SADE BIT_ULL(8)
> > > > > > > +#define RISCV_IOMMU_DC_TC_DPE BIT_ULL(9)
> > > > > > > +#define RISCV_IOMMU_DC_TC_SBE BIT_ULL(10)
> > > > > > > +#define RISCV_IOMMU_DC_TC_SXL BIT_ULL(11)
> > > > > > > +
> > > > > > > +/* Second-stage (aka G-stage) context fields */
> > > > > > > +#define RISCV_IOMMU_DC_IOHGATP_PPN RISCV_IOMMU_ATP_PPN_FIELD
> > > > > > > +#define RISCV_IOMMU_DC_IOHGATP_GSCID GENMASK_ULL(59, 44)
> > > > > > > +#define RISCV_IOMMU_DC_IOHGATP_MODE RISCV_IOMMU_ATP_MODE_FIELD
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * enum riscv_iommu_dc_iohgatp_modes - Guest address translation/protection modes
> > > > > > > + * @RISCV_IOMMU_DC_IOHGATP_MODE_BARE: No translation/protection
> > > > > > > + * @RISCV_IOMMU_DC_IOHGATP_MODE_SV32X4: Sv32x4 (2-bit extension of Sv32), when fctl.GXL == 1
> > > > > > > + * @RISCV_IOMMU_DC_IOHGATP_MODE_SV39X4: Sv39x4 (2-bit extension of Sv39), when fctl.GXL == 0
> > > > > > > + * @RISCV_IOMMU_DC_IOHGATP_MODE_SV48X4: Sv48x4 (2-bit extension of Sv48), when fctl.GXL == 0
> > > > > > > + * @RISCV_IOMMU_DC_IOHGATP_MODE_SV57X4: Sv57x4 (2-bit extension of Sv57), when fctl.GXL == 0
> > > > > > > + */
> > > > > > > +enum riscv_iommu_dc_iohgatp_modes {
> > > > > > > + RISCV_IOMMU_DC_IOHGATP_MODE_BARE = 0,
> > > > > > > + RISCV_IOMMU_DC_IOHGATP_MODE_SV32X4 = 8,
> > > > > > > + RISCV_IOMMU_DC_IOHGATP_MODE_SV39X4 = 8,
> > > > > > > + RISCV_IOMMU_DC_IOHGATP_MODE_SV48X4 = 9,
> > > > > > > + RISCV_IOMMU_DC_IOHGATP_MODE_SV57X4 = 10
> > > > > > > +};
> > > > > > > +
> > > > > > > +/* Translation attributes fields */
> > > > > > > +#define RISCV_IOMMU_DC_TA_PSCID GENMASK_ULL(31, 12)
> > > > > > > +
> > > > > > > +/* First-stage context fields */
> > > > > > > +#define RISCV_IOMMU_DC_FSC_PPN RISCV_IOMMU_ATP_PPN_FIELD
> > > > > > > +#define RISCV_IOMMU_DC_FSC_MODE RISCV_IOMMU_ATP_MODE_FIELD
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * enum riscv_iommu_dc_fsc_atp_modes - First stage address translation/protection modes
> > > > > > > + * @RISCV_IOMMU_DC_FSC_MODE_BARE: No translation/protection
> > > > > > > + * @RISCV_IOMMU_DC_FSC_IOSATP_MODE_SV32: Sv32, when dc.tc.SXL == 1
> > > > > > > + * @RISCV_IOMMU_DC_FSC_IOSATP_MODE_SV39: Sv39, when dc.tc.SXL == 0
> > > > > > > + * @RISCV_IOMMU_DC_FSC_IOSATP_MODE_SV48: Sv48, when dc.tc.SXL == 0
> > > > > > > + * @RISCV_IOMMU_DC_FSC_IOSATP_MODE_SV57: Sv57, when dc.tc.SXL == 0
> > > > > > > + * @RISCV_IOMMU_DC_FSC_PDTP_MODE_PD8: 1lvl PDT, 8bit process ids
> > > > > > > + * @RISCV_IOMMU_DC_FSC_PDTP_MODE_PD17: 2lvl PDT, 17bit process ids
> > > > > > > + * @RISCV_IOMMU_DC_FSC_PDTP_MODE_PD20: 3lvl PDT, 20bit process ids
> > > > > > > + *
> > > > > > > + * FSC holds IOSATP when RISCV_IOMMU_DC_TC_PDTV is 0 and PDTP otherwise.
> > > > > > > + * IOSATP controls the first stage address translation (same as the satp register on
> > > > > > > + * the RISC-V MMU), and PDTP holds the process directory table, used to select a
> > > > > > > + * first stage page table based on a process id (for devices that support multiple
> > > > > > > + * process ids).
> > > > > > > + */
> > > > > > > +enum riscv_iommu_dc_fsc_atp_modes {
> > > > > > > + RISCV_IOMMU_DC_FSC_MODE_BARE = 0,
> > > > > > > + RISCV_IOMMU_DC_FSC_IOSATP_MODE_SV32 = 8,
> > > > > > > + RISCV_IOMMU_DC_FSC_IOSATP_MODE_SV39 = 8,
> > > > > > > + RISCV_IOMMU_DC_FSC_IOSATP_MODE_SV48 = 9,
> > > > > > > + RISCV_IOMMU_DC_FSC_IOSATP_MODE_SV57 = 10,
> > > > > > > + RISCV_IOMMU_DC_FSC_PDTP_MODE_PD8 = 1,
> > > > > > > + RISCV_IOMMU_DC_FSC_PDTP_MODE_PD17 = 2,
> > > > > > > + RISCV_IOMMU_DC_FSC_PDTP_MODE_PD20 = 3
> > > > > > > +};
> > > > > > > +
> > > > > > > +/* MSI page table pointer */
> > > > > > > +#define RISCV_IOMMU_DC_MSIPTP_PPN RISCV_IOMMU_ATP_PPN_FIELD
> > > > > > > +#define RISCV_IOMMU_DC_MSIPTP_MODE RISCV_IOMMU_ATP_MODE_FIELD
> > > > > > > +#define RISCV_IOMMU_DC_MSIPTP_MODE_OFF 0
> > > > > > > +#define RISCV_IOMMU_DC_MSIPTP_MODE_FLAT 1
> > > > > > > +
> > > > > > > +/* MSI address mask */
> > > > > > > +#define RISCV_IOMMU_DC_MSI_ADDR_MASK GENMASK_ULL(51, 0)
> > > > > > > +
> > > > > > > +/* MSI address pattern */
> > > > > > > +#define RISCV_IOMMU_DC_MSI_PATTERN GENMASK_ULL(51, 0)
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * struct riscv_iommu_pc - Process Context
> > > > > > > + * @ta: Translation Attributes
> > > > > > > + * @fsc: First stage context
> > > > > > > + *
> > > > > > > + * This structure is used for leaf nodes on the Process Directory Table
> > > > > > > + * See section 2.3 for more details
> > > > > > > + */
> > > > > > > +struct riscv_iommu_pc {
> > > > > > > + u64 ta;
> > > > > > > + u64 fsc;
> > > > > > > +};
> > > > > > > +
> > > > > > > +/* Translation attributes fields */
> > > > > > > +#define RISCV_IOMMU_PC_TA_V BIT_ULL(0)
> > > > > > > +#define RISCV_IOMMU_PC_TA_ENS BIT_ULL(1)
> > > > > > > +#define RISCV_IOMMU_PC_TA_SUM BIT_ULL(2)
> > > > > > > +#define RISCV_IOMMU_PC_TA_PSCID GENMASK_ULL(31, 12)
> > > > > > > +
> > > > > > > +/* First stage context fields */
> > > > > > > +#define RISCV_IOMMU_PC_FSC_PPN RISCV_IOMMU_ATP_PPN_FIELD
> > > > > > > +#define RISCV_IOMMU_PC_FSC_MODE RISCV_IOMMU_ATP_MODE_FIELD
> > > > > > > +
> > > > > > > +/*
> > > > > > > + * Chapter 3: In-memory queue interface
> > > > > > > + */
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * struct riscv_iommu_command - Generic I/O MMU command structure
> > > > > > > + * @dword0: Includes the opcode and the function identifier
> > > > > > > + * @dword1: Opcode specific data
> > > > > > > + *
> > > > > > > + * The commands are interpreted as two 64bit fields, where the first
> > > > > > > + * 7bits of the first field are the opcode which also defines the
> > > > > > > + * command's format, followed by a 3bit field that specifies the
> > > > > > > + * function invoked by that command, and the rest is opcode-specific.
> > > > > > > + * This is a generic struct which will be populated differently
> > > > > > > + * according to each command. For more infos on the commands and
> > > > > > > + * the command queue check section 3.1.
> > > > > > > + */
> > > > > > > +struct riscv_iommu_command {
> > > > > > > + u64 dword0;
> > > > > > > + u64 dword1;
> > > > > > > +};
> > > > > > > +
> > > > > > > +/* Fields on dword0, common for all commands */
> > > > > > > +#define RISCV_IOMMU_CMD_OPCODE GENMASK_ULL(6, 0)
> > > > > > > +#define RISCV_IOMMU_CMD_FUNC GENMASK_ULL(9, 7)
> > > > > > > +
> > > > > > > +/* 3.1.1 I/O MMU Page-table cache invalidation */
> > > > > > > +/* Fields on dword0 */
> > > > > > > +#define RISCV_IOMMU_CMD_IOTINVAL_OPCODE 1
> > > > > > > +#define RISCV_IOMMU_CMD_IOTINVAL_FUNC_VMA 0
> > > > > > > +#define RISCV_IOMMU_CMD_IOTINVAL_FUNC_GVMA 1
> > > > > > > +#define RISCV_IOMMU_CMD_IOTINVAL_AV BIT_ULL(10)
> > > > > > > +#define RISCV_IOMMU_CMD_IOTINVAL_PSCID GENMASK_ULL(31, 12)
> > > > > > > +#define RISCV_IOMMU_CMD_IOTINVAL_PSCV BIT_ULL(32)
> > > > > > > +#define RISCV_IOMMU_CMD_IOTINVAL_GV BIT_ULL(33)
> > > > > > > +#define RISCV_IOMMU_CMD_IOTINVAL_GSCID GENMASK_ULL(59, 44)
> > > > > > > +/* dword1[61:10] is the 4K-aligned page address */
> > > > > > > +#define RISCV_IOMMU_CMD_IOTINVAL_ADDR GENMASK_ULL(61, 10)
> > > > > > > +
> > > > > > > +/* 3.1.2 I/O MMU Command Queue Fences */
> > > > > > > +/* Fields on dword0 */
> > > > > > > +#define RISCV_IOMMU_CMD_IOFENCE_OPCODE 2
> > > > > > > +#define RISCV_IOMMU_CMD_IOFENCE_FUNC_C 0
> > > > > > > +#define RISCV_IOMMU_CMD_IOFENCE_AV BIT_ULL(10)
> > > > > > > +#define RISCV_IOMMU_CMD_IOFENCE_WSI BIT_ULL(11)
> > > > > > > +#define RISCV_IOMMU_CMD_IOFENCE_PR BIT_ULL(12)
> > > > > > > +#define RISCV_IOMMU_CMD_IOFENCE_PW BIT_ULL(13)
> > > > > > > +#define RISCV_IOMMU_CMD_IOFENCE_DATA GENMASK_ULL(63, 32)
> > > > > > > +/* dword1 is the address, word-size aligned and shifted to the right by two bits. */
> > > > > > > +
> > > > > > > +/* 3.1.3 I/O MMU Directory cache invalidation */
> > > > > > > +/* Fields on dword0 */
> > > > > > > +#define RISCV_IOMMU_CMD_IODIR_OPCODE 3
> > > > > > > +#define RISCV_IOMMU_CMD_IODIR_FUNC_INVAL_DDT 0
> > > > > > > +#define RISCV_IOMMU_CMD_IODIR_FUNC_INVAL_PDT 1
> > > > > > > +#define RISCV_IOMMU_CMD_IODIR_PID GENMASK_ULL(31, 12)
> > > > > > > +#define RISCV_IOMMU_CMD_IODIR_DV BIT_ULL(33)
> > > > > > > +#define RISCV_IOMMU_CMD_IODIR_DID GENMASK_ULL(63, 40)
> > > > > > > +/* dword1 is reserved for standard use */
> > > > > > > +
> > > > > > > +/* 3.1.4 I/O MMU PCIe ATS */
> > > > > > > +/* Fields on dword0 */
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_OPCODE 4
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_FUNC_INVAL 0
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_FUNC_PRGR 1
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_PID GENMASK_ULL(31, 12)
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_PV BIT_ULL(32)
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_DSV BIT_ULL(33)
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_RID GENMASK_ULL(55, 40)
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_DSEG GENMASK_ULL(63, 56)
> > > > > > > +/* dword1 is the ATS payload, two different payload types for INVAL and PRGR */
> > > > > > > +
> > > > > > > +/* ATS.INVAL payload*/
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_INVAL_G BIT_ULL(0)
> > > > > > > +/* Bits 1 - 10 are zeroed */
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_INVAL_S BIT_ULL(11)
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_INVAL_UADDR GENMASK_ULL(63, 12)
> > > > > > > +
> > > > > > > +/* ATS.PRGR payload */
> > > > > > > +/* Bits 0 - 31 are zeroed */
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_PRGR_PRG_INDEX GENMASK_ULL(40, 32)
> > > > > > > +/* Bits 41 - 43 are zeroed */
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_PRGR_RESP_CODE GENMASK_ULL(47, 44)
> > > > > > > +#define RISCV_IOMMU_CMD_ATS_PRGR_DST_ID GENMASK_ULL(63, 48)
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * struct riscv_iommu_fq_record - Fault/Event Queue Record
> > > > > > > + * @hdr: Header, includes fault/event cause, PID/DID, transaction type etc
> > > > > > > + * @_reserved: Low 32bits for custom use, high 32bits for standard use
> > > > > > > + * @iotval: Transaction-type/cause specific format
> > > > > > > + * @iotval2: Cause specific format
> > > > > > > + *
> > > > > > > + * The fault/event queue reports events and failures raised when
> > > > > > > + * processing transactions. Each record is a 32byte structure where
> > > > > > > + * the first dword has a fixed format for providing generic infos
> > > > > > > + * regarding the fault/event, and two more dwords are there for
> > > > > > > + * fault/event-specific information. For more details see section
> > > > > > > + * 3.2.
> > > > > > > + */
> > > > > > > +struct riscv_iommu_fq_record {
> > > > > > > + u64 hdr;
> > > > > > > + u64 _reserved;
> > > > > > > + u64 iotval;
> > > > > > > + u64 iotval2;
> > > > > > > +};
> > > > > > > +
> > > > > > > +/* Fields on header */
> > > > > > > +#define RISCV_IOMMU_FQ_HDR_CAUSE GENMASK_ULL(11, 0)
> > > > > > > +#define RISCV_IOMMU_FQ_HDR_PID GENMASK_ULL(31, 12)
> > > > > > > +#define RISCV_IOMMU_FQ_HDR_PV BIT_ULL(32)
> > > > > > > +#define RISCV_IOMMU_FQ_HDR_PRIV BIT_ULL(33)
> > > > > > > +#define RISCV_IOMMU_FQ_HDR_TTYPE GENMASK_ULL(39, 34)
> > > > > > > +#define RISCV_IOMMU_FQ_HDR_DID GENMASK_ULL(63, 40)
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * enum riscv_iommu_fq_causes - Fault/event cause values
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_INST_FAULT: Instruction access fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_RD_ADDR_MISALIGNED: Read address misaligned
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_RD_FAULT: Read load fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_WR_ADDR_MISALIGNED: Write/AMO address misaligned
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_WR_FAULT: Write/AMO access fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_INST_FAULT_S: Instruction page fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_RD_FAULT_S: Read page fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_WR_FAULT_S: Write/AMO page fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_INST_FAULT_VS: Instruction guest page fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_RD_FAULT_VS: Read guest page fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_WR_FAULT_VS: Write/AMO guest page fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_DMA_DISABLED: All inbound transactions disallowed
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_DDT_LOAD_FAULT: DDT entry load access fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_DDT_INVALID: DDT entry invalid
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_DDT_MISCONFIGURED: DDT entry misconfigured
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_TTYPE_BLOCKED: Transaction type disallowed
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_MSI_LOAD_FAULT: MSI PTE load access fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_MSI_INVALID: MSI PTE invalid
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_MSI_MISCONFIGURED: MSI PTE misconfigured
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_MRIF_FAULT: MRIF access fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_PDT_LOAD_FAULT: PDT entry load access fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_PDT_INVALID: PDT entry invalid
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_PDT_MISCONFIGURED: PDT entry misconfigured
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_DDT_CORRUPTED: DDT data corruption
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_PDT_CORRUPTED: PDT data corruption
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_MSI_PT_CORRUPTED: MSI page table data corruption
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_MRIF_CORRUIPTED: MRIF data corruption
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_INTERNAL_DP_ERROR: Internal data path error
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_MSI_WR_FAULT: IOMMU MSI write access fault
> > > > > > > + * @RISCV_IOMMU_FQ_CAUSE_PT_CORRUPTED: First/second stage page table data corruption
> > > > > > > + *
> > > > > > > + * Values are on table 11 of the spec, encodings 275 - 2047 are reserved for standard
> > > > > > > + * use, and 2048 - 4095 for custom use.
> > > > > > > + */
> > > > > > > +enum riscv_iommu_fq_causes {
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_INST_FAULT = 1,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_RD_ADDR_MISALIGNED = 4,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_RD_FAULT = 5,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_WR_ADDR_MISALIGNED = 6,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_WR_FAULT = 7,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_INST_FAULT_S = 12,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_RD_FAULT_S = 13,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_WR_FAULT_S = 15,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_INST_FAULT_VS = 20,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_RD_FAULT_VS = 21,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_WR_FAULT_VS = 23,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_DMA_DISABLED = 256,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_DDT_LOAD_FAULT = 257,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_DDT_INVALID = 258,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_DDT_MISCONFIGURED = 259,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_TTYPE_BLOCKED = 260,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_MSI_LOAD_FAULT = 261,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_MSI_INVALID = 262,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_MSI_MISCONFIGURED = 263,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_MRIF_FAULT = 264,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_PDT_LOAD_FAULT = 265,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_PDT_INVALID = 266,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_PDT_MISCONFIGURED = 267,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_DDT_CORRUPTED = 268,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_PDT_CORRUPTED = 269,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_MSI_PT_CORRUPTED = 270,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_MRIF_CORRUIPTED = 271,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_INTERNAL_DP_ERROR = 272,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_MSI_WR_FAULT = 273,
> > > > > > > + RISCV_IOMMU_FQ_CAUSE_PT_CORRUPTED = 274
> > > > > > > +};
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * enum riscv_iommu_fq_ttypes: Fault/event transaction types
> > > > > > > + * @RISCV_IOMMU_FQ_TTYPE_NONE: None. Fault not caused by an inbound transaction.
> > > > > > > + * @RISCV_IOMMU_FQ_TTYPE_UADDR_INST_FETCH: Instruction fetch from untranslated address
> > > > > > > + * @RISCV_IOMMU_FQ_TTYPE_UADDR_RD: Read from untranslated address
> > > > > > > + * @RISCV_IOMMU_FQ_TTYPE_UADDR_WR: Write/AMO to untranslated address
> > > > > > > + * @RISCV_IOMMU_FQ_TTYPE_TADDR_INST_FETCH: Instruction fetch from translated address
> > > > > > > + * @RISCV_IOMMU_FQ_TTYPE_TADDR_RD: Read from translated address
> > > > > > > + * @RISCV_IOMMU_FQ_TTYPE_TADDR_WR: Write/AMO to translated address
> > > > > > > + * @RISCV_IOMMU_FQ_TTYPE_PCIE_ATS_REQ: PCIe ATS translation request
> > > > > > > + * @RISCV_IOMMU_FW_TTYPE_PCIE_MSG_REQ: PCIe message request
> > > > > > > + *
> > > > > > > + * Values are on table 12 of the spec, type 4 and 10 - 31 are reserved for standard use
> > > > > > > + * and 31 - 63 for custom use.
> > > > > > > + */
> > > > > > > +enum riscv_iommu_fq_ttypes {
> > > > > > > + RISCV_IOMMU_FQ_TTYPE_NONE = 0,
> > > > > > > + RISCV_IOMMU_FQ_TTYPE_UADDR_INST_FETCH = 1,
> > > > > > > + RISCV_IOMMU_FQ_TTYPE_UADDR_RD = 2,
> > > > > > > + RISCV_IOMMU_FQ_TTYPE_UADDR_WR = 3,
> > > > > > > + RISCV_IOMMU_FQ_TTYPE_TADDR_INST_FETCH = 5,
> > > > > > > + RISCV_IOMMU_FQ_TTYPE_TADDR_RD = 6,
> > > > > > > + RISCV_IOMMU_FQ_TTYPE_TADDR_WR = 7,
> > > > > > > + RISCV_IOMMU_FQ_TTYPE_PCIE_ATS_REQ = 8,
> > > > > > > + RISCV_IOMMU_FW_TTYPE_PCIE_MSG_REQ = 9,
> > > > > > > +};
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * struct riscv_iommu_pq_record - PCIe Page Request record
> > > > > > > + * @hdr: Header, includes PID, DID etc
> > > > > > > + * @payload: Holds the page address, request group and permission bits
> > > > > > > + *
> > > > > > > + * For more infos on the PCIe Page Request queue see chapter 3.3.
> > > > > > > + */
> > > > > > > +struct riscv_iommu_pq_record {
> > > > > > > + u64 hdr;
> > > > > > > + u64 payload;
> > > > > > > +};
> > > > > > > +
> > > > > > > +/* Header fields */
> > > > > > > +#define RISCV_IOMMU_PREQ_HDR_PID GENMASK_ULL(31, 12)
> > > > > > > +#define RISCV_IOMMU_PREQ_HDR_PV BIT_ULL(32)
> > > > > > > +#define RISCV_IOMMU_PREQ_HDR_PRIV BIT_ULL(33)
> > > > > > > +#define RISCV_IOMMU_PREQ_HDR_EXEC BIT_ULL(34)
> > > > > > > +#define RISCV_IOMMU_PREQ_HDR_DID GENMASK_ULL(63, 40)
> > > > > > > +
> > > > > > > +/* Payload fields */
> > > > > > > +#define RISCV_IOMMU_PREQ_PAYLOAD_R BIT_ULL(0)
> > > > > > > +#define RISCV_IOMMU_PREQ_PAYLOAD_W BIT_ULL(1)
> > > > > > > +#define RISCV_IOMMU_PREQ_PAYLOAD_L BIT_ULL(2)
> > > > > > > +#define RISCV_IOMMU_PREQ_PAYLOAD_M GENMASK_ULL(2, 0) /* Mask of RWL for convenience */
> > > > > > > +#define RISCV_IOMMU_PREQ_PRG_INDEX GENMASK_ULL(11, 3)
> > > > > > > +#define RISCV_IOMMU_PREQ_UADDR GENMASK_ULL(63, 12)
> > > > > > > +
> > > > > > > +/**
> > > > > > > + * struct riscv_iommu_msi_pte - MSI Page Table Entry
> > > > > > > + * @pte: MSI PTE
> > > > > > > + * @mrif_info: Memory-resident interrupt file info
> > > > > > > + *
> > > > > > > + * The MSI Page Table is used for virtualizing MSIs, so that when
> > > > > > > + * a device sends an MSI to a guest, the IOMMU can reroute it
> > > > > > > + * by translating the MSI address, either to a guest interrupt file
> > > > > > > + * or a memory resident interrupt file (MRIF). Note that this page table
> > > > > > > + * is an array of MSI PTEs, not a multi-level pt, each entry
> > > > > > > + * is a leaf entry. For more infos check out the AIA spec, chapter 9.5.
> > > > > > > + *
> > > > > > > + * Also in basic mode the mrif_info field is ignored by the IOMMU and can
> > > > > > > + * be used by software, any other reserved fields on pte must be zeroed-out
> > > > > > > + * by software.
> > > > > > > + */
> > > > > > > +struct riscv_iommu_msi_pte {
> > > > > > > + u64 pte;
> > > > > > > + u64 mrif_info;
> > > > > > > +};
> > > > > > > +
> > > > > > > +/* Fields on pte */
> > > > > > > +#define RISCV_IOMMU_MSI_PTE_V BIT_ULL(0)
> > > > > > > +#define RISCV_IOMMU_MSI_PTE_M GENMASK_ULL(2, 1)
> > > > > > > +#define RISCV_IOMMU_MSI_PTE_MRIF_ADDR GENMASK_ULL(53, 7) /* When M == 1 (MRIF mode) */
> > > > > > > +#define RISCV_IOMMU_MSI_PTE_PPN RISCV_IOMMU_PPN_FIELD /* When M == 3 (basic mode) */
> > > > > > > +#define RISCV_IOMMU_MSI_PTE_C BIT_ULL(63)
> > > > > > > +
> > > > > > > +/* Fields on mrif_info */
> > > > > > > +#define RISCV_IOMMU_MSI_MRIF_NID GENMASK_ULL(9, 0)
> > > > > > > +#define RISCV_IOMMU_MSI_MRIF_NPPN RISCV_IOMMU_PPN_FIELD
> > > > > > > +#define RISCV_IOMMU_MSI_MRIF_NID_MSB BIT_ULL(60)
> > > > > > > +
> > > > > > > +#endif /* _RISCV_IOMMU_BITS_H_ */
> > > > > > > diff --git a/drivers/iommu/riscv/iommu-platform.c b/drivers/iommu/riscv/iommu-platform.c
> > > > > > > new file mode 100644
> > > > > > > index 000000000000..1b453334fbbe
> > > > > > > --- /dev/null
> > > > > > > +++ b/drivers/iommu/riscv/iommu-platform.c
> > > > > > > @@ -0,0 +1,92 @@
> > > > > > > +// SPDX-License-Identifier: GPL-2.0-only
> > > > > > > +/*
> > > > > > > + * RISC-V IOMMU as a platform device
> > > > > > > + *
> > > > > > > + * Copyright © 2023 FORTH-ICS/CARV
> > > > > > > + * Copyright © 2023-2024 Rivos Inc.
> > > > > > > + *
> > > > > > > + * Authors
> > > > > > > + * Nick Kossifidis <mick at ics.forth.gr>
> > > > > > > + * Tomasz Jeznach <tjeznach at rivosinc.com>
> > > > > > > + */
> > > > > > > +
> > > > > > > +#include <linux/kernel.h>
> > > > > > > +#include <linux/of_platform.h>
> > > > > > > +#include <linux/platform_device.h>
> > > > > > > +
> > > > > > > +#include "iommu-bits.h"
> > > > > > > +#include "iommu.h"
> > > > > > > +
> > > > > > > +static int riscv_iommu_platform_probe(struct platform_device *pdev)
> > > > > > > +{
> > > > > > > + struct device *dev = &pdev->dev;
> > > > > > > + struct riscv_iommu_device *iommu = NULL;
> > > > > > > + struct resource *res = NULL;
> > > > > > > + int vec;
> > > > > > > +
> > > > > > > + iommu = devm_kzalloc(dev, sizeof(*iommu), GFP_KERNEL);
> > > > > > > + if (!iommu)
> > > > > > > + return -ENOMEM;
> > > > > > > +
> > > > > > > + iommu->dev = dev;
> > > > > > > + iommu->reg = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
> > > > > > > + if (IS_ERR(iommu->reg))
> > > > > > > + return dev_err_probe(dev, PTR_ERR(iommu->reg),
> > > > > > > + "could not map register region\n");
> > > > > > > +
> > > > > > > + dev_set_drvdata(dev, iommu);
> > > > > > > +
> > > > > > > + /* Check device reported capabilities / features. */
> > > > > > > + iommu->caps = riscv_iommu_readq(iommu, RISCV_IOMMU_REG_CAP);
> > > > > > > + iommu->fctl = riscv_iommu_readl(iommu, RISCV_IOMMU_REG_FCTL);
> > > > > > > +
> > > > > > > + /* For now we only support WSI */
> > > > > > > + switch (FIELD_GET(RISCV_IOMMU_CAP_IGS, iommu->caps)) {
> > > > > > > + case RISCV_IOMMU_CAP_IGS_WSI:
> > > > > > > + case RISCV_IOMMU_CAP_IGS_BOTH:
> > > > > > > + break;
> > > > > > > + default:
> > > > > > > + return dev_err_probe(dev, -ENODEV,
> > > > > > > + "unable to use wire-signaled interrupts\n");
> > > > > > > + }
> > > > > > > +
> > > > > > > + iommu->irqs_count = platform_irq_count(pdev);
> > > > > > > + if (iommu->irqs_count <= 0)
> > > > > > > + return dev_err_probe(dev, -ENODEV,
> > > > > > > + "no IRQ resources provided\n");
> > > > > > > + if (iommu->irqs_count > RISCV_IOMMU_INTR_COUNT)
> > > > > > > + iommu->irqs_count = RISCV_IOMMU_INTR_COUNT;
> > > > > > > +
> > > > > > > + for (vec = 0; vec < iommu->irqs_count; vec++)
> > > > > > > + iommu->irqs[vec] = platform_get_irq(pdev, vec);
> > > > > > > +
> > > > > > > + /* Enable wire-signaled interrupts, fctl.WSI */
> > > > > > > + if (!(iommu->fctl & RISCV_IOMMU_FCTL_WSI)) {
> > > > > > > + iommu->fctl |= RISCV_IOMMU_FCTL_WSI;
> > > > > > > + riscv_iommu_writel(iommu, RISCV_IOMMU_REG_FCTL, iommu->fctl);
> > > > > > > + }
> > > > > > > +
> > > > > > > + return riscv_iommu_init(iommu);
> > > > > > > +};
> > > > > > > +
> > > > > > > +static void riscv_iommu_platform_remove(struct platform_device *pdev)
> > > > > > > +{
> > > > > > > + riscv_iommu_remove(dev_get_drvdata(&pdev->dev));
> > > > > > > +};
> > > > > > > +
> > > > > > > +static const struct of_device_id riscv_iommu_of_match[] = {
> > > > > > > + {.compatible = "riscv,iommu",},
> > > > > > > + {},
> > > > > > > +};
> > > > > > > +
> > > > > > > +static struct platform_driver riscv_iommu_platform_driver = {
> > > > > > > + .probe = riscv_iommu_platform_probe,
> > > > > > > + .remove_new = riscv_iommu_platform_remove,
> > > > > > > + .driver = {
> > > > > > > + .name = "riscv,iommu",
> > > > > > > + .of_match_table = riscv_iommu_of_match,
> > > > > > > + .suppress_bind_attrs = true,
> > > > > > > + },
> > > > > > > +};
> > > > > > > +
> > > > > > > +builtin_platform_driver(riscv_iommu_platform_driver);
> > > > > > > diff --git a/drivers/iommu/riscv/iommu.c b/drivers/iommu/riscv/iommu.c
> > > > > > > new file mode 100644
> > > > > > > index 000000000000..3c5a6b49669d
> > > > > > > --- /dev/null
> > > > > > > +++ b/drivers/iommu/riscv/iommu.c
> > > > > > > @@ -0,0 +1,99 @@
> > > > > > > +// SPDX-License-Identifier: GPL-2.0-only
> > > > > > > +/*
> > > > > > > + * IOMMU API for RISC-V IOMMU implementations.
> > > > > > > + *
> > > > > > > + * Copyright © 2022-2024 Rivos Inc.
> > > > > > > + * Copyright © 2023 FORTH-ICS/CARV
> > > > > > > + *
> > > > > > > + * Authors
> > > > > > > + * Tomasz Jeznach <tjeznach at rivosinc.com>
> > > > > > > + * Nick Kossifidis <mick at ics.forth.gr>
> > > > > > > + */
> > > > > > > +
> > > > > > > +#define pr_fmt(fmt) "riscv-iommu: " fmt
> > > > > > > +
> > > > > > > +#include <linux/compiler.h>
> > > > > > > +#include <linux/crash_dump.h>
> > > > > > > +#include <linux/init.h>
> > > > > > > +#include <linux/iommu.h>
> > > > > > > +#include <linux/kernel.h>
> > > > > > > +
> > > > > > > +#include "iommu-bits.h"
> > > > > > > +#include "iommu.h"
> > > > > > > +
> > > > > > > +/* Timeouts in [us] */
> > > > > > > +#define RISCV_IOMMU_DDTP_TIMEOUT 50000
> > > > > > > +
> > > > > > > +/*
> > > > > > > + * This is best effort IOMMU translation shutdown flow.
> > > > > > > + * Disable IOMMU without waiting for hardware response.
> > > > > > > + */
> > > > > > > +static void riscv_iommu_disable(struct riscv_iommu_device *iommu)
> > > > > > > +{
> > > > > > > + riscv_iommu_writeq(iommu, RISCV_IOMMU_REG_DDTP, 0);
> > > > > > > + riscv_iommu_writel(iommu, RISCV_IOMMU_REG_CQCSR, 0);
> > > > > > > + riscv_iommu_writel(iommu, RISCV_IOMMU_REG_FQCSR, 0);
> > > > > > > + riscv_iommu_writel(iommu, RISCV_IOMMU_REG_PQCSR, 0);
> > > > > > > +}
> > > > > > > +
> > > > > > > +static int riscv_iommu_init_check(struct riscv_iommu_device *iommu)
> > > > > > > +{
> > > > > > > + u64 ddtp;
> > > > > > > +
> > > > > > > + /*
> > > > > > > + * Make sure the IOMMU is switched off or in pass-through mode during
> > > > > > > + * regular boot flow and disable translation when we boot into a kexec
> > > > > > > + * kernel and the previous kernel left them enabled.
> > > > > > > + */
> > > > > > > + ddtp = riscv_iommu_readq(iommu, RISCV_IOMMU_REG_DDTP);
> > > > > > > + if (ddtp & RISCV_IOMMU_DDTP_BUSY)
> > > > > > > + return -EBUSY;
> > > > > > > +
> > > > > > > + if (FIELD_GET(RISCV_IOMMU_DDTP_MODE, ddtp) > RISCV_IOMMU_DDTP_MODE_BARE) {
> > > > > > > + if (!is_kdump_kernel())
> > > > > > > + return -EBUSY;
> > > > > > > + riscv_iommu_disable(iommu);
> > > > > > > + }
> > > > > > > +
> > > > > > > + /* Configure accesses to in-memory data structures for CPU-native byte order. */
> > > > > > > + if (IS_ENABLED(CONFIG_CPU_BIG_ENDIAN) != !!(iommu->fctl & RISCV_IOMMU_FCTL_BE)) {
> > > > > > > + if (!(iommu->caps & RISCV_IOMMU_CAP_END))
> > > > > > > + return -EINVAL;
> > > > > > > + riscv_iommu_writel(iommu, RISCV_IOMMU_REG_FCTL,
> > > > > > > + iommu->fctl ^ RISCV_IOMMU_FCTL_BE);
> > > > > > > + iommu->fctl = riscv_iommu_readl(iommu, RISCV_IOMMU_REG_FCTL);
> > > > > > > + if (IS_ENABLED(CONFIG_CPU_BIG_ENDIAN) != !!(iommu->fctl & RISCV_IOMMU_FCTL_BE))
> > > > > > > + return -EINVAL;
> > > > > > > + }
> > > > > > > +
> > > > > > > + return 0;
> > > > > > > +}
> > > > > > > +
> > > > > > > +void riscv_iommu_remove(struct riscv_iommu_device *iommu)
> > > > > > > +{
> > > > > > > + iommu_device_sysfs_remove(&iommu->iommu);
> > > > > > > +}
> > > > > > > +
> > > > > > > +int riscv_iommu_init(struct riscv_iommu_device *iommu)
> > > > > > > +{
> > > > > > > + int rc;
> > > > > > > +
> > > > > > > + rc = riscv_iommu_init_check(iommu);
> > > > > > > + if (rc)
> > > > > > > + return dev_err_probe(iommu->dev, rc, "unexpected device state\n");
> > > > > > > +
> > > > > > > + /*
> > > > > > > + * Placeholder for a complete IOMMU device initialization. For now,
> > > > > > > + * only bare minimum: enable global identity mapping mode and register sysfs.
> > > > > > > + */
> > > > > > > + riscv_iommu_writeq(iommu, RISCV_IOMMU_REG_DDTP,
> > > > > > > + FIELD_PREP(RISCV_IOMMU_DDTP_MODE, RISCV_IOMMU_DDTP_MODE_BARE));
> > > > > > > +
> > > > > > > + rc = iommu_device_sysfs_add(&iommu->iommu, NULL, NULL, "riscv-iommu@%s",
> > > > > > > + dev_name(iommu->dev));
> > > > > > > + if (rc)
> > > > > > > + return dev_err_probe(iommu->dev, rc,
> > > > > > > + "cannot register sysfs interface\n");
> > > > > > > +
> > > > > > > + return 0;
> > > > > > > +}
> > > > > > > diff --git a/drivers/iommu/riscv/iommu.h b/drivers/iommu/riscv/iommu.h
> > > > > > > new file mode 100644
> > > > > > > index 000000000000..700e33dc2446
> > > > > > > --- /dev/null
> > > > > > > +++ b/drivers/iommu/riscv/iommu.h
> > > > > > > @@ -0,0 +1,62 @@
> > > > > > > +/* SPDX-License-Identifier: GPL-2.0-only */
> > > > > > > +/*
> > > > > > > + * Copyright © 2022-2024 Rivos Inc.
> > > > > > > + * Copyright © 2023 FORTH-ICS/CARV
> > > > > > > + *
> > > > > > > + * Authors
> > > > > > > + * Tomasz Jeznach <tjeznach at rivosinc.com>
> > > > > > > + * Nick Kossifidis <mick at ics.forth.gr>
> > > > > > > + */
> > > > > > > +
> > > > > > > +#ifndef _RISCV_IOMMU_H_
> > > > > > > +#define _RISCV_IOMMU_H_
> > > > > > > +
> > > > > > > +#include <linux/iommu.h>
> > > > > > > +#include <linux/types.h>
> > > > > > > +#include <linux/iopoll.h>
> > > > > > > +
> > > > > > > +#include "iommu-bits.h"
> > > > > > > +
> > > > > > > +struct riscv_iommu_device {
> > > > > > > + /* iommu core interface */
> > > > > > > + struct iommu_device iommu;
> > > > > > > +
> > > > > > > + /* iommu hardware */
> > > > > > > + struct device *dev;
> > > > > > > +
> > > > > > > + /* hardware control register space */
> > > > > > > + void __iomem *reg;
> > > > > > > +
> > > > > > > + /* supported and enabled hardware capabilities */
> > > > > > > + u64 caps;
> > > > > > > + u32 fctl;
> > > > > > > +
> > > > > > > + /* available interrupt numbers, MSI or WSI */
> > > > > > > + unsigned int irqs[RISCV_IOMMU_INTR_COUNT];
> > > > > > > + unsigned int irqs_count;
> > > > > > > +};
> > > > > > > +
> > > > > > > +int riscv_iommu_init(struct riscv_iommu_device *iommu);
> > > > > > > +void riscv_iommu_remove(struct riscv_iommu_device *iommu);
> > > > > > > +
> > > > > > > +#define riscv_iommu_readl(iommu, addr) \
> > > > > > > + readl_relaxed((iommu)->reg + (addr))
> > > > > > > +
> > > > > > > +#define riscv_iommu_readq(iommu, addr) \
> > > > > > > + readq_relaxed((iommu)->reg + (addr))
> > > > > > > +
> > > > > > > +#define riscv_iommu_writel(iommu, addr, val) \
> > > > > > > + writel_relaxed((val), (iommu)->reg + (addr))
> > > > > > > +
> > > > > > > +#define riscv_iommu_writeq(iommu, addr, val) \
> > > > > > > + writeq_relaxed((val), (iommu)->reg + (addr))
> > > > > > > +
> > > > > > > +#define riscv_iommu_readq_timeout(iommu, addr, val, cond, delay_us, timeout_us) \
> > > > > > > + readx_poll_timeout(readq_relaxed, (iommu)->reg + (addr), val, cond, \
> > > > > > > + delay_us, timeout_us)
> > > > > > > +
> > > > > > > +#define riscv_iommu_readl_timeout(iommu, addr, val, cond, delay_us, timeout_us) \
> > > > > > > + readx_poll_timeout(readl_relaxed, (iommu)->reg + (addr), val, cond, \
> > > > > > > + delay_us, timeout_us)
> > > > > > > +
> > > > > > > +#endif
> > > > > > > --
> > > > > > > 2.34.1
> > > > > > >
> > > > > > >
> > > > > > > _______________________________________________
> > > > > > > linux-riscv mailing list
> > > > > > > linux-riscv at lists.infradead.org
> > > > > > > http://lists.infradead.org/mailman/listinfo/linux-riscv
More information about the linux-riscv
mailing list