[PATCH v14 01/18] irqchip/sifive-plic: Convert PLIC driver into a platform driver

[Emil Renner Berthing]

Anup Patel wrote:
> On Wed, Jun 19, 2024 at 11:16 PM Emil Renner Berthing
> <emil.renner.berthing at canonical.com> wrote:
> >
> > Anup Patel wrote:
> > > On Tue, Jun 18, 2024 at 7:00 PM Emil Renner Berthing
> > > <emil.renner.berthing at canonical.com> wrote:
> > > >
> > > > Anup Patel wrote:
> > > > > The PLIC driver does not require very early initialization so convert
> > > > > it into a platform driver.
> > > > >
> > > > > After conversion, the PLIC driver is probed after CPUs are brought-up
> > > > > so setup cpuhp state after context handler of all online CPUs are
> > > > > initialized otherwise PLIC driver crashes for platforms with multiple
> > > > > PLIC instances.
> > > > >
> > > > > Signed-off-by: Anup Patel <apatel at ventanamicro.com>
> > > >
> > > > Hi Anup,
> > > >
> > > > Sorry for the late reply to the mailing list, but ever since 6.9 where this was
> > > > applied my Allwinner D1 based boards no longer boot. This is the log of my
> > > > LicheeRV Dock booting plain 6.10-rc4, locking up and then rebooting due to the
> > > > the watchdog timing out:
> > > >
> > > > https://pastebin.com/raw/nsbzgEKW
> > > >
> > > > On 6.10-rc4 I can bring the same board to boot by reverting this patch and all
> > > > patches building on it. Eg.:
> > > >
> > > >   git revert e306a894bd51 a7fb69ffd7ce abb720579490 \
> > > >              956521064780 a15587277a24 6c725f33d67b \
> > > >              b68d0ff529a9 25d862e183d4 8ec99b033147
> > >
> > > Does your board boot with only SBI timer driver enabled ?
> >
> > I'm not 100% sure this is what you mean, but with this change I can disable
> > CONFIG_SUN4I_TIMER:
> >
> > diff --git a/arch/riscv/Kconfig.socs b/arch/riscv/Kconfig.socs
> > index f51bb24bc84c..0143545348eb 100644
> > --- a/arch/riscv/Kconfig.socs
> > +++ b/arch/riscv/Kconfig.socs
> > @@ -39,7 +39,6 @@ config ARCH_SUNXI
> >         bool "Allwinner sun20i SoCs"
> >         depends on MMU && !XIP_KERNEL
> >         select ERRATA_THEAD
> > -       select SUN4I_TIMER
> >         help
> >           This enables support for Allwinner sun20i platform hardware,
> >           including boards based on the D1 and D1s SoCs.
> >
> >
> > But unfortunately the board still doesn't boot:
> > https://pastebin.com/raw/AwRxcfeu
>
> I think we should enable debug prints in DD core and see
> which device is not getting probed due to lack of a provider.
>
> Just add "#define DEBUG" at the top in drivers/base/core.c
> and boot again with "loglevel=8" kernel parameter (along with
> the above change).

With the above changes this is what I get:
https://pastebin.com/raw/JfRrEahT

/Emil