[PATCH 04/47] arm64: dts: qcom: qcs9100: Add QCS9100 RIDE board dts

[Tengfei Fan]

On 7/3/2024 12:39 PM, Krzysztof Kozlowski wrote:
> On 03/07/2024 04:58, Tengfei Fan wrote:
>> Add support for the QCS9100 RIDE board dts. The current QCS9100 RIDE
>> board dts is directly renamed from the SA8775p RIDE board dts.
>> The difference between the current QCS9100 RIDE board and the SA8775p
>> RIDE board lies solely in the replacement of the SA8775p SoC with the
>> QCS9100 SoC, all other board resources remain the same.
>> The following items have been updated:
>>    - use QCS9100-related compatible names for this board dts.
>>    - replace the inclusion of sa8775p.dtsi with qcs9100.dtsi.
>>    - replace the inclusion of sa8775p-pmics.dtsi with qcs9100-pmics.dtsi
>>
>> Signed-off-by: Tengfei Fan <quic_tengfan at quicinc.com>
>> ---
>>   arch/arm64/boot/dts/qcom/Makefile                         | 2 +-
>>   .../boot/dts/qcom/{sa8775p-ride.dts => qcs9100-ride.dts}  | 8 ++++----
>>   2 files changed, 5 insertions(+), 5 deletions(-)
>>   rename arch/arm64/boot/dts/qcom/{sa8775p-ride.dts => qcs9100-ride.dts} (99%)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> index 5576c7d6ea06..a7a3792b0691 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -103,6 +103,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-1000.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= qcs404-evb-4000.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= qcs6490-rb3gen2.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= qcs8550-aim300-aiot.dtb
>> +dtb-$(CONFIG_ARCH_QCOM)	+= qcs9100-ride.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= qdu1000-idp.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= qrb2210-rb1.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= qrb4210-rb2.dtb
>> @@ -112,7 +113,6 @@ dtb-$(CONFIG_ARCH_QCOM)	+= qru1000-idp.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= sa8155p-adp.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= sa8295p-adp.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= sa8540p-ride.dtb
>> -dtb-$(CONFIG_ARCH_QCOM)	+= sa8775p-ride.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-acer-aspire1.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-idp.dtb
>>   dtb-$(CONFIG_ARCH_QCOM)	+= sc7180-trogdor-coachz-r1.dtb
>> diff --git a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts b/arch/arm64/boot/dts/qcom/qcs9100-ride.dts
>> similarity index 99%
>> rename from arch/arm64/boot/dts/qcom/sa8775p-ride.dts
>> rename to arch/arm64/boot/dts/qcom/qcs9100-ride.dts
>> index 26ad05bd3b3f..2415d34b8aa5 100644
>> --- a/arch/arm64/boot/dts/qcom/sa8775p-ride.dts
>> +++ b/arch/arm64/boot/dts/qcom/qcs9100-ride.dts
>> @@ -8,12 +8,12 @@
>>   #include <dt-bindings/gpio/gpio.h>
>>   #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
>>   
>> -#include "sa8775p.dtsi"
>> -#include "sa8775p-pmics.dtsi"
>> +#include "qcs9100.dtsi"
>> +#include "qcs9100-pmics.dtsi"
>>   
>>   / {
>> -	model = "Qualcomm SA8775P Ride";
>> -	compatible = "qcom,sa8775p-ride", "qcom,sa8775p";
>> +	model = "Qualcomm QCS9100 Ride";
>> +	compatible = "qcom,qcs9100-ride", "qcom,qcs9100";
> 
> It does not look like you tested the DTS against bindings. Please run
> `make dtbs_check W=1` (see
> Documentation/devicetree/bindings/writing-schema.rst or
> https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
> for instructions).
> 
> Your own internal guideline tells you to perform above tests, doesn't it?
> 
> Best regards,
> Krzysztof
> 

I have performed relevant check, and it's possible that there are some 
issues about the parameters used. I will follow your advice and refer to 
the relevant documentation to perform DTBS check again, ensuring that 
similar issues do not arise in the future.

-- 
Thx and BRs,
Tengfei Fan