[RFC PATCH 1/6] dt-bindings: pinctrl: starfive: add JH8100 pinctrl bindings

Krzysztof Kozlowski krzysztof.kozlowski at linaro.org
Tue Feb 20 00:09:39 PST 2024


On 07/02/2024 03:42, Yuklin Soo wrote:
>>
>>> +    type: object
>>> +    additionalProperties: false
>>> +    patternProperties:
>>> +      '-pins$':
>>> +        type: object
>>> +        description: |
>>> +          A pinctrl node should contain at least one subnode representing the
>>> +          pinctrl groups available in the domain. Each subnode will list the
>>> +          pins it needs, and how they should be configured, with regard to
>>> +          muxer configuration, bias, input enable/disable, input schmitt
>>> +          trigger enable/disable, slew-rate and drive strength.
>>> +        allOf:
>>> +          - $ref: /schemas/pinctrl/pincfg-node.yaml
>>> +          - $ref: /schemas/pinctrl/pinmux-node.yaml
>>> +        additionalProperties: false
>>
>> Why the rest of the properties is not applicable?
> 
> The regex “-pins$” make sure all client subnode names end with suffix “-pins” (e.g, i2c0-scl-pins, i2c-sda-pins)

I did not talk about subnodes.

I asked why the rest of pincfg and pinmux schema properties are not allowed.


>>> +#define PAD_GPIO9_E				9
>>> +#define PAD_GPIO10_E				10
>>> +#define PAD_GPIO11_E				11
>>> +#define PAD_GPIO12_E				12
>>> +#define PAD_GPIO13_E				13
>>> +#define PAD_GPIO14_E				14
>>> +#define PAD_GPIO15_E				15
>>> +#define PAD_GPIO16_E				16
>>> +#define PAD_GPIO17_E				17
>>> +#define PAD_GPIO18_E				18
>>> +#define PAD_GPIO19_E				19
>>> +#define PAD_GPIO20_E				20
>>> +#define PAD_GPIO21_E				21
>>> +#define PAD_GPIO22_E				22
>>> +#define PAD_GPIO23_E				23
>>> +#define PAD_GPIO24_E				24
>>> +#define PAD_GPIO25_E				25
>>> +#define PAD_GPIO26_E				26
>>> +#define PAD_GPIO27_E				27
>>> +#define PAD_GPIO28_E				28
>>> +#define PAD_GPIO29_E				29
>>> +#define PAD_GPIO30_E				30
>>> +#define PAD_GPIO31_E				31
>>> +#define PAD_GPIO32_E				32
>>> +#define PAD_GPIO33_E				33
>>> +#define PAD_GPIO34_E				34
>>> +#define PAD_GPIO35_E				35
>>> +#define PAD_GPIO36_E				36
>>> +#define PAD_GPIO37_E				37
>>> +#define PAD_GPIO38_E				38
>>> +#define PAD_GPIO39_E				39
>>> +#define PAD_GPIO40_E				40
>>> +#define PAD_GPIO41_E				41
>>> +#define PAD_GPIO42_E				42
>>> +#define PAD_GPIO43_E				43
>>> +#define PAD_GPIO44_E				44
>>> +#define PAD_GPIO45_E				45
>>> +#define PAD_GPIO46_E				46
>>> +#define PAD_GPIO47_E				47
>>
>> Please explain why do you think these are bindings?
> 
> The “PAD_GPIO*_*” represent the pin numbers of the PAD_GPIO pins in each domain.

So not bindings.

> It is part of the pinmux value. The pinmux value is generated by macro GPIOMUX as follow:
> 
> pinmux = <GPIOMUX(Pin_Number, Output_Signal_Index,
>                    Output_Enable_Signal_Index,
>                    Input_Signal_Index)>;
> 
> Use I2C0 as example,
> pinmux = <GPIOMUX(PAD_GPIO9_E, GPOUT_SYS_I2C0_CLK,
>                     GPOEN_SYS_I2C0_CLK,
>                     GPI_SYS_I2C0_CLK)>;

So not bindings. Read my question - I did not ask what are these. I
asked why these are bindings. Your explanation suggests these are not. Drop.

You can always store some defines in DTS headers.

> 
>>
>>> +
>>> +/* sys_iomux_east syscon */
>>> +#define SYS_E_VREF_GPIO_E0_SYSCON_REG		0x0fc
>>> +#define SYS_E_VREF_GPIO_E0_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_E_VREF_GPIO_E0_SYSCON_SHIFT		0
>>> +#define SYS_E_VREF_GPIO_E1_SYSCON_REG		0x100
>>> +#define SYS_E_VREF_GPIO_E1_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_E_VREF_GPIO_E1_SYSCON_SHIFT		0
>>> +#define SYS_E_VREF_GPIO_E2_SYSCON_REG		0x104
>>> +#define SYS_E_VREF_GPIO_E2_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_E_VREF_GPIO_E2_SYSCON_SHIFT		0
>>> +#define SYS_E_VREF_GPIO_E3_SYSCON_REG		0x108
>>> +#define SYS_E_VREF_GPIO_E3_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_E_VREF_GPIO_E3_SYSCON_SHIFT		0
>>> +#define SYS_E_VREF_ATB_STG1_SYSCON_REG		0x10c
>>> +#define SYS_E_VREF_ATB_STG1_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_E_VREF_ATB_STG1_SYSCON_SHIFT	0
>>> +#define SYS_E_VREF_ATB_USB_SYSCON_REG		0x110
>>> +#define SYS_E_VREF_ATB_USB_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_E_VREF_ATB_USB_SYSCON_SHIFT		0
>>
>> Drop all of this, not bindings.
> 
> All the SYSCON macros will be removed.
> 
>>
>>> +
>>> +/* sys_iomux_gmac pins */
>>> +#define PAD_GMAC1_MDC				0
>>> +#define PAD_GMAC1_MDIO				1
>>> +#define PAD_GMAC1_RXD0				2
>>> +#define PAD_GMAC1_RXD1				3
>>> +#define PAD_GMAC1_RXD2				4
>>> +#define PAD_GMAC1_RXD3				5
>>> +#define PAD_GMAC1_RXDV				6
>>> +#define PAD_GMAC1_RXC				7
>>> +#define PAD_GMAC1_TXD0				8
>>> +#define PAD_GMAC1_TXD1				9
>>> +#define PAD_GMAC1_TXD2				10
>>> +#define PAD_GMAC1_TXD3				11
>>> +#define PAD_GMAC1_TXEN				12
>>> +#define PAD_GMAC1_TXC				13
>>> +
>>> +/* sys_iomux_gmac vref syscon registers */
>>> +#define SYS_G_VREF_GMAC1_SYSCON_REG		0x08
>>> +#define SYS_G_VREF_GMAC1_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_VREF_GMAC1_SYSCON_SHIFT		0
>>> +#define SYS_G_VREF_SDIO1_SYSCON_REG		0x0c
>>> +#define SYS_G_VREF_SDIO1_SYSCON_MASK		GENMASK(1, 0)
>>> +#define SYS_G_VREF_SDIO1_SYSCON_SHIFT		0
>>
>> Drop all this.
> 
> All the GMAC and SYSCON macros will be removed.
> 
>>
>>> +
>>> +/* sys_iomux_gmac interface (rmii/rgmii) syscon registers */
>>> +#define SYS_G_GMAC1_MDC_SYSCON_REG		0x10
>>> +#define SYS_G_GMAC1_MDC_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_GMAC1_MDC_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_MDIO_SYSCON_REG		0x14
>>> +#define SYS_G_GMAC1_MDIO_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_GMAC1_MDIO_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_RXD0_SYSCON_REG		0x18
>>> +#define SYS_G_GMAC1_RXD0_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_GMAC1_RXD0_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_RXD1_SYSCON_REG		0x1c
>>> +#define SYS_G_GMAC1_RXD1_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_GMAC1_RXD1_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_RXD2_SYSCON_REG		0x20
>>> +#define SYS_G_GMAC1_RXD2_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_GMAC1_RXD2_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_RXD3_SYSCON_REG		0x24
>>> +#define SYS_G_GMAC1_RXD3_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_GMAC1_RXD3_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_RXDV_SYSCON_REG		0x28
>>> +#define SYS_G_GMAC1_RXDV_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_GMAC1_RXDV_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_RXC_SYSCON_REG		0x2c
>>> +#define SYS_G_GMAC1_RXC_SYSCON_MASK		GENMASK(1, 0)
>>> +#define SYS_G_GMAC1_RXC_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_TXD0_SYSCON_REG		0x30
>>> +#define SYS_G_GMAC1_TXD0_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_GMAC1_TXD0_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_TXD1_SYSCON_REG		0x34
>>> +#define SYS_G_GMAC1_TXD1_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_GMAC1_TXD1_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_TXD2_SYSCON_REG		0x38
>>> +#define SYS_G_GMAC1_TXD2_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_GMAC1_TXD2_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_TXD3_SYSCON_REG		0x3c
>>> +#define SYS_G_GMAC1_TXD3_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_GMAC1_TXD3_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_TXEN_SYSCON_REG		0x40
>>> +#define SYS_G_GMAC1_TXEN_SYSCON_MASK		GENMASK(1,
>> 0)
>>> +#define SYS_G_GMAC1_TXEN_SYSCON_SHIFT		0
>>> +#define SYS_G_GMAC1_TXC_SYSCON_REG		0x44
>>> +#define SYS_G_GMAC1_TXC_SYSCON_MASK		GENMASK(1, 0)
>>> +#define SYS_G_GMAC1_TXC_SYSCON_SHIFT		0
>>
>> Drop all this.
> 
> All the SYSCON macros will be removed.
> 
>>
>>
>>> +
>>> +/* sys_iomux_gmac timing (slew rate) registers */
>>
>> Srsly, "registers", so not bindings.
> 
> All these will be removed.
> 
>>
>>
>>> +
>>> +#define GPOUT_LOW				0
>>> +#define GPOUT_HIGH				1
>>
>> That's it. Really. Please do not redefine existing bindings.
>>
>>> +
>>> +#define GPOEN_ENABLE				0
>>> +#define GPOEN_DISABLE				1
>>> +
>>> +#define GPI_NONE				255
>>> +
>>> +/* vref syscon value  */
>>> +#define PAD_VREF_SYSCON_IO_3V3			0
>>> +#define PAD_VREF_SYSCON_IO_1V8			2
>>> +
>>> +/* gmac interface (rmii/rgmii) syscon value */
>>> +#define GMAC_RMII_MODE				0	/* RMII
>> mode,  DVDD 2.5V/3.3V */
>>> +#define GMAC_RGMII_MODE				1	/*
>> RGMII mode, DVDD 1.8V/2.5V */
>>> +
>>> +/* gmac timing syscon value */
>>> +#define GMAC_SLEW_RATE_FAST			0
>>> +#define GMAC_SLEW_RATE_SLOW			1
>>
>> Drop all above.
> 
> All SYSCON macros will be dropped.
> However, the following will be kept in the header file,
> #define GPOUT_LOW                               0
> #define GPOUT_HIGH                              1
> 
> #define GPOEN_ENABLE                            0
> #define GPOEN_DISABLE                           1
> 
> #define GPI_NONE                                255

No, why?

I think I commented quite strongly about it.

Best regards,
Krzysztof




More information about the linux-riscv mailing list