[PATCH v2 2/4] pinctrl: spacemit: add support for SpacemiT K1 SoC
Yixun Lan
dlan at gentoo.org
Mon Aug 26 20:30:57 PDT 2024
Hi Inochi:
On 16:16 Mon 26 Aug , Inochi Amaoto wrote:
> On Sun, Aug 25, 2024 at 01:10:03PM GMT, Yixun Lan wrote:
> > SpacemiT's K1 SoC has a pinctrl controller which use single register
> > to describe all functions, which include bias pull up/down, drive
> > strength, schmitter trigger, slew rate, strong pull up, mux mode.
> >
> > Signed-off-by: Yixun Lan <dlan at gentoo.org>
> > ---
> > drivers/pinctrl/Kconfig | 1 +
> > drivers/pinctrl/Makefile | 1 +
> > drivers/pinctrl/spacemit/Kconfig | 17 +
> > drivers/pinctrl/spacemit/Makefile | 3 +
> > drivers/pinctrl/spacemit/pinctrl-k1.c | 1012 +++++++++++++++++++++++++++++++++
> > drivers/pinctrl/spacemit/pinctrl-k1.h | 36 ++
> > 6 files changed, 1070 insertions(+)
> >
> > diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
> > index 7e4f93a3bc7ac..8358da47cd00d 100644
> > --- a/drivers/pinctrl/Kconfig
> > +++ b/drivers/pinctrl/Kconfig
> > @@ -583,6 +583,7 @@ source "drivers/pinctrl/qcom/Kconfig"
> > source "drivers/pinctrl/realtek/Kconfig"
> > source "drivers/pinctrl/renesas/Kconfig"
> > source "drivers/pinctrl/samsung/Kconfig"
> > +source "drivers/pinctrl/spacemit/Kconfig"
> > source "drivers/pinctrl/spear/Kconfig"
> > source "drivers/pinctrl/sprd/Kconfig"
> > source "drivers/pinctrl/starfive/Kconfig"
> > diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
> > index cc809669405ab..553beead7ffa0 100644
> > --- a/drivers/pinctrl/Makefile
> > +++ b/drivers/pinctrl/Makefile
> > @@ -73,6 +73,7 @@ obj-y += qcom/
> > obj-$(CONFIG_ARCH_REALTEK) += realtek/
> > obj-$(CONFIG_PINCTRL_RENESAS) += renesas/
> > obj-$(CONFIG_PINCTRL_SAMSUNG) += samsung/
> > +obj-y += spacemit/
> > obj-$(CONFIG_PINCTRL_SPEAR) += spear/
> > obj-y += sprd/
> > obj-$(CONFIG_SOC_STARFIVE) += starfive/
> > diff --git a/drivers/pinctrl/spacemit/Kconfig b/drivers/pinctrl/spacemit/Kconfig
> > new file mode 100644
> > index 0000000000000..168f8a5ffbb95
> > --- /dev/null
> > +++ b/drivers/pinctrl/spacemit/Kconfig
> > @@ -0,0 +1,17 @@
> > +# SPDX-License-Identifier: GPL-2.0-only
> > +#
> > +# Sophgo SoC PINCTRL drivers
> > +#
> > +
> > +config PINCTRL_SPACEMIT_K1
> > + tristate "SpacemiT K1 SoC Pinctrl driver"
> > + depends on ARCH_SPACEMIT || COMPILE_TEST
> > + depends on OF
> > + select GENERIC_PINCTRL_GROUPS
> > + select GENERIC_PINMUX_FUNCTIONS
> > + select GENERIC_PINCONF
> > + help
> > + Say Y to select the pinctrl driver for K1 SoC.
> > + This pin controller allows selecting the mux function for
> > + each pin. This driver can also be built as a module called
> > + pinctrl-k1.
> > diff --git a/drivers/pinctrl/spacemit/Makefile b/drivers/pinctrl/spacemit/Makefile
> > new file mode 100644
> > index 0000000000000..fede1e80fe0ff
> > --- /dev/null
> > +++ b/drivers/pinctrl/spacemit/Makefile
> > @@ -0,0 +1,3 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +
> > +obj-$(CONFIG_PINCTRL_SPACEMIT_K1) += pinctrl-k1.o
> > diff --git a/drivers/pinctrl/spacemit/pinctrl-k1.c b/drivers/pinctrl/spacemit/pinctrl-k1.c
> > new file mode 100644
> > index 0000000000000..9ed9530c78150
> > --- /dev/null
> > +++ b/drivers/pinctrl/spacemit/pinctrl-k1.c
> > @@ -0,0 +1,1012 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/* Copyright (c) 2024 Yixun Lan <dlan at gentoo.org> */
> > +
> > +#include <linux/bitfield.h>
> > +#include <linux/export.h>
> > +#include <linux/io.h>
> > +#include <linux/of.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/seq_file.h>
> > +#include <linux/spinlock.h>
> > +#include <linux/module.h>
> > +
> > +#include <linux/pinctrl/consumer.h>
> > +#include <linux/pinctrl/machine.h>
> > +#include <linux/pinctrl/pinconf-generic.h>
> > +#include <linux/pinctrl/pinconf.h>
> > +#include <linux/pinctrl/pinctrl.h>
> > +#include <linux/pinctrl/pinmux.h>
> > +
> > +#include <dt-bindings/pinctrl/spacemit,k1-pinctrl.h>
> > +
> > +#include "../core.h"
> > +#include "../pinctrl-utils.h"
> > +#include "../pinconf.h"
> > +#include "../pinmux.h"
> > +#include "pinctrl-k1.h"
> > +
> > +/*
> > + * +---------+----------+-----------+--------+--------+----------+--------+
> > + * | pull | drive | schmitter | slew | edge | strong | mux |
> > + * | up/down | strength | trigger | rate | detect | pull | mode |
> > + * +---------+----------+-----------+--------+--------+----------+--------+
> > + * 3 bits 3 bits 2 bits 1 bit 3 bits 1 bit 3 bits
> > + */
> > +
> > +#define PAD_MUX GENMASK(2, 0)
> > +#define PAD_STRONG_PULL BIT(3)
> > +#define PAD_EDGE_RISE BIT(4)
> > +#define PAD_EDGE_FALL BIT(5)
> > +#define PAD_EDGE_CLEAR BIT(6)
> > +#define PAD_SLEW_RATE GENMASK(12, 11)
> > +#define PAD_SLEW_RATE_EN BIT(7)
> > +#define PAD_SCHMITT GENMASK(9, 8)
> > +#define PAD_DRIVE GENMASK(12, 10)
> > +#define PAD_PULLDOWN BIT(13)
> > +#define PAD_PULLUP BIT(14)
> > +#define PAD_PULL_EN BIT(15)
> > +
> > +#define spacemit_pin_to_reg(pctrl, pin) ((pctrl)->regs + (pin << 2))
> > +
> > +struct spacemit_pin {
> > + u16 pin;
> > + u16 flags;
> > +};
> > +
> > +struct spacemit_pinctrl {
> > + struct device *dev;
> > + struct pinctrl_dev *pctl_dev;
> > + const struct spacemit_pinctrl_data *data;
> > + struct pinctrl_desc pdesc;
> > +
> > + struct list_head gpiofuncs;
> > +
> > + struct mutex mutex;
> > + raw_spinlock_t lock;
> > +
> > + void __iomem *regs;
> > +};
> > +
> > +struct spacemit_pinctrl_data {
> > + const struct pinctrl_pin_desc *pins;
> > + const struct spacemit_pin *data;
> > + u16 npins;
> > +};
> > +
> > +struct spacemit_gpiofunc_range {
> > + u32 offset;
> > + u32 npins;
> > + u32 gpiofunc;
> > + struct list_head node;
> > +};
> > +
> > +struct spacemit_pin_mux_config {
> > + const struct spacemit_pin *pin;
> > + u32 config;
> > +};
> > +
> > +struct spacemit_pin_drv_strength {
> > + u8 val;
> > + u32 mA;
> > +};
> > +
> > +static unsigned int spacemit_dt_get_pin(u32 value)
> > +{
> > + return (value >> 16) & GENMASK(15, 0);
> > +}
> > +
> > +static unsigned int spacemit_dt_get_pin_mux(u32 value)
> > +{
> > + return value & GENMASK(15, 0);
> > +}
> > +
> > +static const struct spacemit_pin *spacemit_get_pin(struct spacemit_pinctrl *pctrl,
> > + unsigned long pin)
> > +{
> > + const struct spacemit_pin *pdata = pctrl->data->data;
> > + int i;
> > +
> > + for (i = 0; i < pctrl->data->npins; i++) {
> > + if (pin == pdata[i].pin)
> > + return &pdata[i];
> > + }
> > +
> > + return NULL;
> > +}
> > +
> > +static inline enum spacemit_pin_io_type spacemit_to_pin_io_type(
> > + const struct spacemit_pin *pin)
> > +{
> > + return K1_PIN_GET_IO_TYPE(pin->flags);
> > +}
> > +
> > +/* External: IO voltage via external source, can be 1.8V or 3.3V */
> > +static const char * const io_type_desc[] = {
> > + "None",
> > + "Fixed/1V8",
> > + "Fixed/3V3",
> > + "External",
> > +};
> > +
> > +static void spacemit_pctrl_dbg_show(struct pinctrl_dev *pctldev,
> > + struct seq_file *seq, unsigned int pin)
> > +{
> > + struct spacemit_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
> > + const struct spacemit_pin *spin = spacemit_get_pin(pctrl, pin);
> > + enum spacemit_pin_io_type type = spacemit_to_pin_io_type(spin);
> > + void __iomem *reg;
> > + u32 value;
> > +
> > + seq_printf(seq, "pin: %u ", spin->pin);
> > +
> > + seq_printf(seq, "type: %s ", io_type_desc[type]);
> > +
> > + reg = spacemit_pin_to_reg(pctrl, spin->pin);
> > + value = readl(reg);
> > + seq_printf(seq, "mux: 0x%08x ", value);
> > +}
> > +
>
> > +/* use IO high level output current as the table */
> > +static struct spacemit_pin_drv_strength spacemit_ds_1v8_tbl[4] = {
> > + { (0 << 1), 11 },
> > + { (1 << 1), 21 },
> > + { (2 << 1), 32 },
> > + { (3 << 1), 42 },
> > +};
> > +
> > +static struct spacemit_pin_drv_strength spacemit_ds_3v3_tbl[8] = {
> > + { 0, 7 },
> > + { 2, 10 },
> > + { 4, 13 },
> > + { 6, 16 },
> > + { 1, 19 },
> > + { 3, 23 },
> > + { 5, 26 },
> > + { 7, 29 },
> > +};
>
> Why these two use different format?
>
I can adjust it, but personally no preference here, it's not much different
the underlying logic is for 1v8 table it's using bit[12:11], while 3v3 table
using bit[12:10], with MASK bit[12:10], there is one bit shift for 1v8
> > +
> > +static inline u8 spacemit_get_ds_value(struct spacemit_pin_drv_strength *tbl,
> > + u32 num, u32 mA)
> > +{
> > + int i;
> > +
> > + for (i = 0; i < num; i++)
> > + if (mA <= tbl[i].mA)
> > + return tbl[i].val;
> > +
> > + return tbl[num - 1].val;
> > +}
> > +
> > +static inline u8 spacemit_get_driver_strength(enum spacemit_pin_io_type type,
> > + u32 mA)
> > +{
> > + switch (type) {
> > + case IO_TYPE_1V8:
> > + return spacemit_get_ds_value(spacemit_ds_1v8_tbl,
> > + ARRAY_SIZE(spacemit_ds_1v8_tbl),
> > + mA);
> > + case IO_TYPE_3V3:
> > + return spacemit_get_ds_value(spacemit_ds_3v3_tbl,
> > + ARRAY_SIZE(spacemit_ds_3v3_tbl),
> > + mA);
> > + default:
> > + return 0;
> > + }
> > +}
> > +
> > +static int spacemit_pctrl_dt_node_to_map(struct pinctrl_dev *pctldev,
> > + struct device_node *np,
> > + struct pinctrl_map **maps,
> > + unsigned int *num_maps)
> > +{
> > + struct spacemit_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
> > + struct device *dev = pctrl->dev;
> > + struct device_node *child;
> > + struct pinctrl_map *map;
> > + const char **grpnames;
> > + const char *grpname;
> > + int ngroups = 0;
> > + int nmaps = 0;
> > + int ret;
> > +
> > + for_each_available_child_of_node(np, child)
> > + ngroups += 1;
> > +
> > + grpnames = devm_kcalloc(dev, ngroups, sizeof(*grpnames), GFP_KERNEL);
> > + if (!grpnames)
> > + return -ENOMEM;
> > +
> > + map = devm_kcalloc(dev, ngroups * 2, sizeof(*map), GFP_KERNEL);
> > + if (!map)
> > + return -ENOMEM;
> > +
> > + ngroups = 0;
> > + mutex_lock(&pctrl->mutex);
> > + for_each_available_child_of_node(np, child) {
> > + int npins = of_property_count_u32_elems(child, "pinmux");
> > + unsigned int *pins;
> > + struct spacemit_pin_mux_config *pinmuxs;
> > + u32 config;
> > + int i;
> > +
> > + if (npins < 1) {
> > + dev_err(dev, "invalid pinctrl group %pOFn.%pOFn\n",
> > + np, child);
> > + ret = -EINVAL;
> > + goto dt_failed;
> > + }
> > +
> > + grpname = devm_kasprintf(dev, GFP_KERNEL, "%pOFn.%pOFn",
> > + np, child);
> > + if (!grpname) {
> > + ret = -ENOMEM;
> > + goto dt_failed;
> > + }
> > +
> > + grpnames[ngroups++] = grpname;
> > +
> > + pins = devm_kcalloc(dev, npins, sizeof(*pins), GFP_KERNEL);
> > + if (!pins) {
> > + ret = -ENOMEM;
> > + goto dt_failed;
> > + }
> > +
> > + pinmuxs = devm_kcalloc(dev, npins, sizeof(*pinmuxs), GFP_KERNEL);
> > + if (!pinmuxs) {
> > + ret = -ENOMEM;
> > + goto dt_failed;
> > + }
> > +
> > + for (i = 0; i < npins; i++) {
> > + ret = of_property_read_u32_index(child, "pinmux",
> > + i, &config);
> > +
> > + if (ret)
> > + goto dt_failed;
> > +
> > + pins[i] = spacemit_dt_get_pin(config);
> > + pinmuxs[i].config = config;
> > + pinmuxs[i].pin = spacemit_get_pin(pctrl, pins[i]);
> > +
> > + if (!pinmuxs[i].pin) {
> > + dev_err(dev, "failed to get pin %d\n", pins[i]);
> > + ret = -ENODEV;
> > + goto dt_failed;
> > + }
> > + }
> > +
>
> It will be better to check the power-source before inserting a map.
>
Ok, I will think about this, maybe a more generic sanity checking function
> > + map[nmaps].type = PIN_MAP_TYPE_MUX_GROUP;
> > + map[nmaps].data.mux.function = np->name;
> > + map[nmaps].data.mux.group = grpname;
> > + nmaps += 1;
> > +
> > + ret = pinctrl_generic_add_group(pctldev, grpname,
> > + pins, npins, pinmuxs);
> > + if (ret < 0) {
> > + dev_err(dev, "failed to add group %s: %d\n", grpname, ret);
> > + goto dt_failed;
> > + }
> > +
> > + ret = pinconf_generic_parse_dt_config(child, pctldev,
> > + &map[nmaps].data.configs.configs,
> > + &map[nmaps].data.configs.num_configs);
> > + if (ret) {
> > + dev_err(dev, "failed to parse pin config of group %s: %d\n",
> > + grpname, ret);
> > + goto dt_failed;
> > + }
> > +
> > + if (map[nmaps].data.configs.num_configs == 0)
> > + continue;
> > +
> > + map[nmaps].type = PIN_MAP_TYPE_CONFIGS_GROUP;
> > + map[nmaps].data.configs.group_or_pin = grpname;
> > + nmaps += 1;
> > + }
> > +
> > + ret = pinmux_generic_add_function(pctldev, np->name,
> > + grpnames, ngroups, NULL);
> > + if (ret < 0) {
> > + dev_err(dev, "error adding function %s: %d\n", np->name, ret);
> > + goto function_failed;
> > + }
> > +
> > + *maps = map;
> > + *num_maps = nmaps;
> > + mutex_unlock(&pctrl->mutex);
> > +
> > + return 0;
> > +
> > +dt_failed:
> > + of_node_put(child);
> > +function_failed:
> > + pinctrl_utils_free_map(pctldev, map, nmaps);
> > + mutex_unlock(&pctrl->mutex);
> > + return ret;
> > +}
> > +
> > +static const struct pinctrl_ops spacemit_pctrl_ops = {
> > + .get_groups_count = pinctrl_generic_get_group_count,
> > + .get_group_name = pinctrl_generic_get_group_name,
> > + .get_group_pins = pinctrl_generic_get_group_pins,
> > + .pin_dbg_show = spacemit_pctrl_dbg_show,
> > + .dt_node_to_map = spacemit_pctrl_dt_node_to_map,
> > + .dt_free_map = pinctrl_utils_free_map,
> > +};
> > +
> > +static int spacemit_pmx_set_mux(struct pinctrl_dev *pctldev,
> > + unsigned int fsel, unsigned int gsel)
> > +{
> > + struct spacemit_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
> > + const struct group_desc *group;
> > + const struct spacemit_pin_mux_config *configs;
> > + unsigned int i, mux;
> > + void __iomem *reg;
> > +
> > + group = pinctrl_generic_get_group(pctldev, gsel);
> > + if (!group)
> > + return -EINVAL;
> > +
> > + configs = group->data;
> > +
> > + for (i = 0; i < group->grp.npins; i++) {
> > + const struct spacemit_pin *spin = configs[i].pin;
> > + u32 value = configs[i].config;
> > + unsigned long flags;
> > +
> > + reg = spacemit_pin_to_reg(pctrl, spin->pin);
> > + mux = spacemit_dt_get_pin_mux(value);
> > +
> > + raw_spin_lock_irqsave(&pctrl->lock, flags);
> > + value = readl_relaxed(reg) & ~PAD_MUX;
> > + writel_relaxed(mux | value, reg);
> > + raw_spin_unlock_irqrestore(&pctrl->lock, flags);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int spacemit_request_gpio(struct pinctrl_dev *pctldev,
> > + struct pinctrl_gpio_range *range,
> > + unsigned int pin)
> > +{
> > + struct spacemit_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
> > + struct spacemit_gpiofunc_range *frange = NULL;
> > + struct list_head *pos, *tmp;
> > + void __iomem *reg;
> > +
> > + list_for_each_safe(pos, tmp, &pctrl->gpiofuncs) {
> > + frange = list_entry(pos, struct spacemit_gpiofunc_range, node);
> > + if (pin >= frange->offset + frange->npins
> > + || pin < frange->offset)
> > + continue;
> > +
> > + reg = spacemit_pin_to_reg(pctrl, pin);
> > + writel(frange->gpiofunc | PAD_EDGE_CLEAR, reg);
> > +
> > + break;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static const struct pinmux_ops spacemit_pmx_ops = {
> > + .get_functions_count = pinmux_generic_get_function_count,
> > + .get_function_name = pinmux_generic_get_function_name,
> > + .get_function_groups = pinmux_generic_get_function_groups,
> > + .set_mux = spacemit_pmx_set_mux,
> > + .gpio_request_enable = spacemit_request_gpio,
> > +};
> > +
> > +#define PIN_CONFIG_K1_SLEW_RATE_ENABLE (PIN_CONFIG_END + 1)
> > +#define PIN_CONFIG_K1_STRONG_PULL_UP (PIN_CONFIG_END + 2)
> > +
> > +static const struct pinconf_generic_params spacemit_pinconf_custom_params[] = {
> > + { "spacemit,slew-rate-disable", PIN_CONFIG_K1_SLEW_RATE_ENABLE, 0 },
> > + { "spacemit,slew-rate-enable", PIN_CONFIG_K1_SLEW_RATE_ENABLE, 1 },
>
> > + { "spacemit,strong-pull-up", PIN_CONFIG_K1_STRONG_PULL_UP, 1 },
>
> default enable?
>
default value is 0 if this property not added, otherwise 1
but, as suggested by Krzysztof, will drop this property and fold it into bias-pull-up
> > +};
> > +
> > +static int spacemit_add_gpio_func(struct device_node *node, struct spacemit_pinctrl *pctrl)
> > +{
> > + const char *propname = "spacemit,gpio-range";
> > + const char *cellname = "#spacemit,gpio-range-cells";
> > + struct of_phandle_args gpiospec;
> > + struct spacemit_gpiofunc_range *range;
> > + int ret, i;
> > +
> > + for (i = 0; ; i++) {
> > + ret = of_parse_phandle_with_args(node, propname, cellname,
> > + i, &gpiospec);
> > + /* Do not treat it as error. Only treat it as end condition. */
> > + if (ret) {
> > + ret = 0;
> > + break;
> > + }
> > + range = devm_kzalloc(pctrl->dev, sizeof(*range), GFP_KERNEL);
> > + if (!range) {
> > + ret = -ENOMEM;
> > + break;
> > + }
> > + range->offset = gpiospec.args[0];
> > + range->npins = gpiospec.args[1];
> > + range->gpiofunc = gpiospec.args[2];
> > + mutex_lock(&pctrl->mutex);
> > + list_add_tail(&range->node, &pctrl->gpiofuncs);
> > + mutex_unlock(&pctrl->mutex);
> > + }
> > +
> > + return ret;
> > +}
> > +
> > +static int spacemit_pinconf_get(struct pinctrl_dev *pctldev,
> > + unsigned int pin, unsigned long *config)
> > +{
> > + struct spacemit_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
> > + int param = pinconf_to_config_param(*config);
> > + u32 value, arg;
> > +
> > + if (!pin)
> > + return -EINVAL;
> > +
> > + value = readl(spacemit_pin_to_reg(pctrl, pin));
> > +
> > + switch (param) {
> > + case PIN_CONFIG_BIAS_DISABLE:
> > + arg = !FIELD_GET(PAD_PULL_EN, value);
> > + break;
> > + case PIN_CONFIG_BIAS_PULL_DOWN:
> > + arg = FIELD_GET(PAD_PULLDOWN, value);
> > + break;
> > + case PIN_CONFIG_BIAS_PULL_UP:
> > + arg = FIELD_GET(PAD_PULLUP, value);
> > + break;
> > + case PIN_CONFIG_DRIVE_STRENGTH_UA:
> > + arg = FIELD_GET(PAD_DRIVE, value);
> > + break;
> > + case PIN_CONFIG_INPUT_SCHMITT:
> > + arg = FIELD_GET(PAD_SCHMITT, value);
> > + break;
> > + case PIN_CONFIG_SLEW_RATE:
> > + arg = FIELD_GET(PAD_SLEW_RATE, value);
> > + break;
> > + case PIN_CONFIG_K1_SLEW_RATE_ENABLE:
> > + arg = FIELD_GET(PAD_SLEW_RATE_EN, value);
> > + break;
> > + case PIN_CONFIG_K1_STRONG_PULL_UP:
> > + arg = FIELD_GET(PAD_STRONG_PULL, value);
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + *config = pinconf_to_config_packed(param, arg);
> > +
> > + return 0;
> > +}
> > +
> > +static int spacemit_pinconf_generate_config(const struct spacemit_pin *spin,
> > + unsigned long *configs,
> > + unsigned int num_configs,
> > + u32 *value)
> > +{
> > + enum spacemit_pin_io_type type;
> > + int i, param;
> > + u32 v = 0, voltage = 0, arg, val;
>
> > +#define ENABLE_DRV_STRENGTH BIT(1)
> > +#define ENABLE_SLEW_RATE BIT(2)
>
> move this before the function.
>
Ok
> > + u32 flag = 0, drv_strength, slew_rate;
> > +
> > + if (!spin)
> > + return -EINVAL;
> > +
> > + for (i = 0; i < num_configs; i++) {
> > + param = pinconf_to_config_param(configs[i]);
> > + arg = pinconf_to_config_argument(configs[i]);
> > +
> > + switch (param) {
> > + case PIN_CONFIG_BIAS_DISABLE:
> > + v &= ~(PAD_PULL_EN | PAD_PULLDOWN | PAD_PULLUP);
> > + break;
> > + case PIN_CONFIG_BIAS_PULL_DOWN:
> > + v &= ~PAD_PULLDOWN;
> > + v |= PAD_PULL_EN;
> > + v |= FIELD_PREP(PAD_PULLDOWN, arg);
> > + break;
> > + case PIN_CONFIG_BIAS_PULL_UP:
> > + v &= ~PAD_PULLUP;
> > + v |= PAD_PULL_EN;
> > + v |= FIELD_PREP(PAD_PULLUP, arg);
> > + break;
> > + case PIN_CONFIG_DRIVE_STRENGTH_UA:
> > + flag |= ENABLE_DRV_STRENGTH;
> > + drv_strength = arg;
> > + break;
> > + case PIN_CONFIG_INPUT_SCHMITT:
> > + slew_rate = arg;
> > + break;
> > + case PIN_CONFIG_POWER_SOURCE:
> > + voltage = arg;
> > + break;
> > + case PIN_CONFIG_SLEW_RATE:
> > + flag |= ENABLE_SLEW_RATE;
> > + break;
> > + case PIN_CONFIG_K1_SLEW_RATE_ENABLE:
> > + if (arg)
> > + v |= PAD_SLEW_RATE_EN;
> > + else
> > + v &= ~PAD_SLEW_RATE_EN;
> > + break;
> > + case PIN_CONFIG_K1_STRONG_PULL_UP:
> > + v &= ~PAD_STRONG_PULL;
> > + v |= FIELD_PREP(PAD_STRONG_PULL, arg);
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > + }
> > +
> > + if (flag & ENABLE_DRV_STRENGTH) {
> > + type = spacemit_to_pin_io_type(spin);
> > +
> > + /* fix external io type */
> > + if (type == IO_TYPE_EXTERNAL) {
> > + switch (voltage) {
> > + case 1800:
> > + type = IO_TYPE_1V8;
> > + break;
> > + case 3300:
> > + type = IO_TYPE_3V3;
> > + break;
> > + default:
> > + pr_err("pin(%d) lack power source\n", spin->pin);
> > + return -EINVAL;
> > + }
> > + }
> > +
> > + val = spacemit_get_driver_strength(type, drv_strength);
> > +
> > + v &= ~PAD_DRIVE;
> > + v |= FIELD_PREP(PAD_DRIVE, val);
> > + }
> > +
>
> > + if (flag & ENABLE_SLEW_RATE) {
> > + v &= ~PAD_SLEW_RATE;
> > + v |= FIELD_PREP(PAD_SLEW_RATE, arg);
> > + /* check, driver strength & slew rate */
> > + if (flag & ENABLE_DRV_STRENGTH) {
> > + if (slew_rate != FIELD_GET(PAD_SLEW_RATE, v))
> > + pr_warn("%s: slew rate conflict with driver strength\n", __func__);
>
> Should this return -EINVAL?
>
due to slew rate share same register bits with drive strength (bit[12:11]),
there is always value of slew rate setting implicitly, so I would like to
just give a warning instead of failure if there is value conflicts, which mean
the drive favor settings from drive strength.. and the design logic from hw is
that higher drive strength lead to more fast slew rate.
> > + } else {
> > + v &= ~PAD_SCHMITT;
> > + v |= FIELD_PREP(PAD_SCHMITT, slew_rate);
I have some typo here while doing copy & paste, will fix it
> > + }
> > + }
> > +
> > + *value = v;
> > +
> > + return 0;
> > +}
> > +
> > +static int spacemit_pin_set_config(struct spacemit_pinctrl *pctrl,
> > + unsigned int pin,
> > + u32 value)
> > +{
> > + const struct spacemit_pin *spin = spacemit_get_pin(pctrl, pin);
> > + void __iomem *reg;
> > + unsigned long flags;
> > + unsigned int mux;
> > +
> > + if (!pin)
> > + return -EINVAL;
> > +
> > + reg = spacemit_pin_to_reg(pctrl, spin->pin);
> > +
> > + raw_spin_lock_irqsave(&pctrl->lock, flags);
> > + mux = readl_relaxed(reg) & PAD_MUX;
> > + writel_relaxed(mux | value, reg);
> > + raw_spin_unlock_irqrestore(&pctrl->lock, flags);
> > +
> > + return 0;
> > +}
> > +
> > +static int spacemit_pinconf_set(struct pinctrl_dev *pctldev,
> > + unsigned int pin, unsigned long *configs,
> > + unsigned int num_configs)
> > +{
> > + struct spacemit_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
> > + const struct spacemit_pin *spin = spacemit_get_pin(pctrl, pin);
> > + u32 value;
> > +
> > + if (spacemit_pinconf_generate_config(spin, configs, num_configs, &value))
> > + return -EINVAL;
> > +
> > + return spacemit_pin_set_config(pctrl, pin, value);
> > +}
> > +
> > +static int spacemit_pinconf_group_set(struct pinctrl_dev *pctldev,
> > + unsigned int gsel,
> > + unsigned long *configs,
> > + unsigned int num_configs)
> > +{
> > + struct spacemit_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
> > + const struct spacemit_pin *spin;
> > + const struct group_desc *group;
> > + u32 value;
> > + int i;
> > +
> > + group = pinctrl_generic_get_group(pctldev, gsel);
> > + if (!group)
> > + return -EINVAL;
> > +
> > + spin = spacemit_get_pin(pctrl, group->grp.pins[0]);
> > + if (spacemit_pinconf_generate_config(spin, configs, num_configs, &value))
> > + return -EINVAL;
> > +
> > + for (i = 0; i < group->grp.npins; i++)
> > + spacemit_pin_set_config(pctrl, group->grp.pins[i], value);
> > +
> > + return 0;
> > +}
> > +
>
> > +static void spacemit_pinconf_dbg_show(struct pinctrl_dev *pctldev,
> > + struct seq_file *seq, unsigned int pin)
> > +{
> > + struct spacemit_pinctrl *pctrl = pinctrl_dev_get_drvdata(pctldev);
> > + const struct spacemit_pin *spin = spacemit_get_pin(pctrl, pin);
> > + enum spacemit_pin_io_type type = spacemit_to_pin_io_type(spin);
> > + void __iomem *reg;
> > +
> > + reg = spacemit_pin_to_reg(pctrl, pin);
> > + seq_printf(seq, " reg (0x%x), io (%d)\n", readl(reg), type);
> > +}
> > +
>
> I think this is a duplicate of "spacemit_pctrl_dbg_show".
>
yes, right
that's due to the hw using single register to provide all conf & mux,
I would drop this function, or improve it to describe more underlying pinconf bits
> > +static const struct pinconf_ops spacemit_pinconf_ops = {
> > + .pin_config_get = spacemit_pinconf_get,
> > + .pin_config_set = spacemit_pinconf_set,
> > + .pin_config_group_set = spacemit_pinconf_group_set,
> > + .pin_config_dbg_show = spacemit_pinconf_dbg_show,
> > + .is_generic = true,
> > +};
> > +
> > +static int spacemit_pinctrl_probe(struct platform_device *pdev)
> > +{
> > + struct device_node *np = pdev->dev.of_node;
> > + struct device *dev = &pdev->dev;
> > + struct spacemit_pinctrl *pctrl;
> > + const struct spacemit_pinctrl_data *pctrl_data;
> > + int ret;
> > +
> > + pctrl_data = device_get_match_data(dev);
> > + if (!pctrl_data)
> > + return -ENODEV;
> > +
> > + if (pctrl_data->npins == 0)
> > + return dev_err_probe(dev, -EINVAL, "invalid pin data\n");
> > +
> > + pctrl = devm_kzalloc(dev, sizeof(*pctrl), GFP_KERNEL);
> > + if (!pctrl)
> > + return -ENOMEM;
> > +
> > + pctrl->regs = devm_platform_ioremap_resource(pdev, 0);
> > + if (IS_ERR(pctrl->regs))
> > + return PTR_ERR(pctrl->regs);
> > +
> > + pctrl->pdesc.name = dev_name(dev);
> > + pctrl->pdesc.pins = pctrl_data->pins;
> > + pctrl->pdesc.npins = pctrl_data->npins;
> > + pctrl->pdesc.pctlops = &spacemit_pctrl_ops;
> > + pctrl->pdesc.pmxops = &spacemit_pmx_ops;
> > + pctrl->pdesc.confops = &spacemit_pinconf_ops;
> > + pctrl->pdesc.num_custom_params = ARRAY_SIZE(spacemit_pinconf_custom_params);
> > + pctrl->pdesc.custom_params = spacemit_pinconf_custom_params;
> > + pctrl->pdesc.owner = THIS_MODULE;
> > +
> > + pctrl->data = pctrl_data;
> > + pctrl->dev = dev;
> > + raw_spin_lock_init(&pctrl->lock);
> > + INIT_LIST_HEAD(&pctrl->gpiofuncs);
> > + mutex_init(&pctrl->mutex);
> > +
> > + platform_set_drvdata(pdev, pctrl);
> > +
> > + ret = devm_pinctrl_register_and_init(dev, &pctrl->pdesc,
> > + pctrl, &pctrl->pctl_dev);
> > + if (ret)
> > + return dev_err_probe(dev, ret,
> > + "fail to register pinctrl driver\n");
> > + ret = spacemit_add_gpio_func(np, pctrl);
> > + if (ret < 0)
> > + return dev_err_probe(dev, ret,
> > + "fail to get gpio function\n");
> > +
> > + return pinctrl_enable(pctrl->pctl_dev);
> > +}
> > +
> > +static const struct pinctrl_pin_desc k1_pin_desc[] = {
> > + PINCTRL_PIN(GPIO_00, "GPIO_00"),
> > + PINCTRL_PIN(GPIO_01, "GPIO_01"),
> > + PINCTRL_PIN(GPIO_02, "GPIO_02"),
> > + PINCTRL_PIN(GPIO_03, "GPIO_03"),
> > + PINCTRL_PIN(GPIO_04, "GPIO_04"),
> > + PINCTRL_PIN(GPIO_05, "GPIO_05"),
> > + PINCTRL_PIN(GPIO_06, "GPIO_06"),
> > + PINCTRL_PIN(GPIO_07, "GPIO_07"),
> > + PINCTRL_PIN(GPIO_08, "GPIO_08"),
> > + PINCTRL_PIN(GPIO_09, "GPIO_09"),
> > + PINCTRL_PIN(GPIO_10, "GPIO_10"),
> > + PINCTRL_PIN(GPIO_11, "GPIO_11"),
> > + PINCTRL_PIN(GPIO_12, "GPIO_12"),
> > + PINCTRL_PIN(GPIO_13, "GPIO_13"),
> > + PINCTRL_PIN(GPIO_14, "GPIO_14"),
> > + PINCTRL_PIN(GPIO_15, "GPIO_15"),
> > + PINCTRL_PIN(GPIO_16, "GPIO_16"),
> > + PINCTRL_PIN(GPIO_17, "GPIO_17"),
> > + PINCTRL_PIN(GPIO_18, "GPIO_18"),
> > + PINCTRL_PIN(GPIO_19, "GPIO_19"),
> > + PINCTRL_PIN(GPIO_20, "GPIO_20"),
> > + PINCTRL_PIN(GPIO_21, "GPIO_21"),
> > + PINCTRL_PIN(GPIO_22, "GPIO_22"),
> > + PINCTRL_PIN(GPIO_23, "GPIO_23"),
> > + PINCTRL_PIN(GPIO_24, "GPIO_24"),
> > + PINCTRL_PIN(GPIO_25, "GPIO_25"),
> > + PINCTRL_PIN(GPIO_26, "GPIO_26"),
> > + PINCTRL_PIN(GPIO_27, "GPIO_27"),
> > + PINCTRL_PIN(GPIO_28, "GPIO_28"),
> > + PINCTRL_PIN(GPIO_29, "GPIO_29"),
> > + PINCTRL_PIN(GPIO_30, "GPIO_30"),
> > + PINCTRL_PIN(GPIO_31, "GPIO_31"),
> > + PINCTRL_PIN(GPIO_32, "GPIO_32"),
> > + PINCTRL_PIN(GPIO_33, "GPIO_33"),
> > + PINCTRL_PIN(GPIO_34, "GPIO_34"),
> > + PINCTRL_PIN(GPIO_35, "GPIO_35"),
> > + PINCTRL_PIN(GPIO_36, "GPIO_36"),
> > + PINCTRL_PIN(GPIO_37, "GPIO_37"),
> > + PINCTRL_PIN(GPIO_38, "GPIO_38"),
> > + PINCTRL_PIN(GPIO_39, "GPIO_39"),
> > + PINCTRL_PIN(GPIO_40, "GPIO_40"),
> > + PINCTRL_PIN(GPIO_41, "GPIO_41"),
> > + PINCTRL_PIN(GPIO_42, "GPIO_42"),
> > + PINCTRL_PIN(GPIO_43, "GPIO_43"),
> > + PINCTRL_PIN(GPIO_44, "GPIO_44"),
> > + PINCTRL_PIN(GPIO_45, "GPIO_45"),
> > + PINCTRL_PIN(GPIO_46, "GPIO_46"),
> > + PINCTRL_PIN(GPIO_47, "GPIO_47"),
> > + PINCTRL_PIN(GPIO_48, "GPIO_48"),
> > + PINCTRL_PIN(GPIO_49, "GPIO_49"),
> > + PINCTRL_PIN(GPIO_50, "GPIO_50"),
> > + PINCTRL_PIN(GPIO_51, "GPIO_51"),
> > + PINCTRL_PIN(GPIO_52, "GPIO_52"),
> > + PINCTRL_PIN(GPIO_53, "GPIO_53"),
> > + PINCTRL_PIN(GPIO_54, "GPIO_54"),
> > + PINCTRL_PIN(GPIO_55, "GPIO_55"),
> > + PINCTRL_PIN(GPIO_56, "GPIO_56"),
> > + PINCTRL_PIN(GPIO_57, "GPIO_57"),
> > + PINCTRL_PIN(GPIO_58, "GPIO_58"),
> > + PINCTRL_PIN(GPIO_59, "GPIO_59"),
> > + PINCTRL_PIN(GPIO_60, "GPIO_60"),
> > + PINCTRL_PIN(GPIO_61, "GPIO_61"),
> > + PINCTRL_PIN(GPIO_62, "GPIO_62"),
> > + PINCTRL_PIN(GPIO_63, "GPIO_63"),
> > + PINCTRL_PIN(GPIO_64, "GPIO_64"),
> > + PINCTRL_PIN(GPIO_65, "GPIO_65"),
> > + PINCTRL_PIN(GPIO_66, "GPIO_66"),
> > + PINCTRL_PIN(GPIO_67, "GPIO_67"),
> > + PINCTRL_PIN(GPIO_68, "GPIO_68"),
> > + PINCTRL_PIN(GPIO_69, "GPIO_69"),
> > + PINCTRL_PIN(GPIO_70, "GPIO_70/PRI_DTI"),
> > + PINCTRL_PIN(GPIO_71, "GPIO_71/PRI_TMS"),
> > + PINCTRL_PIN(GPIO_72, "GPIO_72/PRI_TCK"),
> > + PINCTRL_PIN(GPIO_73, "GPIO_73/PRI_TDO"),
> > + PINCTRL_PIN(GPIO_74, "GPIO_74"),
> > + PINCTRL_PIN(GPIO_75, "GPIO_75"),
> > + PINCTRL_PIN(GPIO_76, "GPIO_76"),
> > + PINCTRL_PIN(GPIO_77, "GPIO_77"),
> > + PINCTRL_PIN(GPIO_78, "GPIO_78"),
> > + PINCTRL_PIN(GPIO_79, "GPIO_79"),
> > + PINCTRL_PIN(GPIO_80, "GPIO_80"),
> > + PINCTRL_PIN(GPIO_81, "GPIO_81"),
> > + PINCTRL_PIN(GPIO_82, "GPIO_82"),
> > + PINCTRL_PIN(GPIO_83, "GPIO_83"),
> > + PINCTRL_PIN(GPIO_84, "GPIO_84"),
> > + PINCTRL_PIN(GPIO_85, "GPIO_85"),
> > + PINCTRL_PIN(GPIO_86, "GPIO_86"),
> > + PINCTRL_PIN(GPIO_87, "GPIO_87"),
> > + PINCTRL_PIN(GPIO_88, "GPIO_88"),
> > + PINCTRL_PIN(GPIO_89, "GPIO_89"),
> > + PINCTRL_PIN(GPIO_90, "GPIO_90"),
> > + PINCTRL_PIN(GPIO_91, "GPIO_91"),
> > + PINCTRL_PIN(GPIO_92, "GPIO_92"),
> > + PINCTRL_PIN(GPIO_93, "GPIO_93/PWR_SCL"),
> > + PINCTRL_PIN(GPIO_94, "GPIO_94/PWR_SDA"),
> > + PINCTRL_PIN(GPIO_95, "GPIO_95/VCX0_EN"),
> > + PINCTRL_PIN(GPIO_96, "GPIO_96/DVL0"),
> > + PINCTRL_PIN(GPIO_97, "GPIO_97/DVL1"),
> > + PINCTRL_PIN(GPIO_98, "GPIO_98/QSPI_DAT3"),
> > + PINCTRL_PIN(GPIO_99, "GPIO_99/QSPI_DAT2"),
> > + PINCTRL_PIN(GPIO_100, "GPIO_100/QSPI_DAT1"),
> > + PINCTRL_PIN(GPIO_101, "GPIO_101/QSPI_DAT0"),
> > + PINCTRL_PIN(GPIO_102, "GPIO_102/QSPI_CLK"),
> > + PINCTRL_PIN(GPIO_103, "GPIO_103/QSPI_CSI"),
> > + PINCTRL_PIN(GPIO_104, "GPIO_104/MMC1_DAT3"),
> > + PINCTRL_PIN(GPIO_105, "GPIO_105/MMC1_DAT2"),
> > + PINCTRL_PIN(GPIO_106, "GPIO_106/MMC1_DAT1"),
> > + PINCTRL_PIN(GPIO_107, "GPIO_107/MMC1_DAT0"),
> > + PINCTRL_PIN(GPIO_108, "GPIO_108/MMC1_CMD"),
> > + PINCTRL_PIN(GPIO_109, "GPIO_109/MMC1_CLK"),
> > + PINCTRL_PIN(GPIO_110, "GPIO_110"),
> > + PINCTRL_PIN(GPIO_111, "GPIO_111"),
> > + PINCTRL_PIN(GPIO_112, "GPIO_112"),
> > + PINCTRL_PIN(GPIO_113, "GPIO_113"),
> > + PINCTRL_PIN(GPIO_114, "GPIO_114"),
> > + PINCTRL_PIN(GPIO_115, "GPIO_115"),
> > + PINCTRL_PIN(GPIO_116, "GPIO_116"),
> > + PINCTRL_PIN(GPIO_117, "GPIO_117"),
> > + PINCTRL_PIN(GPIO_118, "GPIO_118"),
> > + PINCTRL_PIN(GPIO_119, "GPIO_119"),
> > + PINCTRL_PIN(GPIO_120, "GPIO_120"),
> > + PINCTRL_PIN(GPIO_121, "GPIO_121"),
> > + PINCTRL_PIN(GPIO_122, "GPIO_122"),
> > + PINCTRL_PIN(GPIO_123, "GPIO_123"),
> > + PINCTRL_PIN(GPIO_124, "GPIO_124"),
> > + PINCTRL_PIN(GPIO_125, "GPIO_125"),
> > + PINCTRL_PIN(GPIO_126, "GPIO_126"),
> > + PINCTRL_PIN(GPIO_127, "GPIO_127"),
> > +};
> > +
> > +static const struct spacemit_pin k1_pin_data[ARRAY_SIZE(k1_pin_desc)] = {
> > + K1_FUNC_PIN(GPIO_00, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_01, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_02, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_03, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_04, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_05, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_06, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_07, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_08, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_09, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_10, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_11, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_12, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_13, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_14, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_15, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_16, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_17, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_18, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_19, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_20, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_21, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_22, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_23, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_24, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_25, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_26, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_27, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_28, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_29, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_30, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_31, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_32, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_33, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_34, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_35, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_36, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_37, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_38, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_39, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_40, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_41, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_42, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_43, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_44, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_45, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_46, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_47, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_48, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_49, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_50, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_51, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_52, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_53, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_54, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_55, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_56, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_57, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_58, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_59, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_60, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_61, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_62, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_63, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_64, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_65, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_66, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_67, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_68, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_69, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_70, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_71, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_72, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_73, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_74, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_75, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_76, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_77, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_78, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_79, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_80, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_81, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_82, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_83, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_84, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_85, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_86, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_87, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_88, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_89, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_90, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_91, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_92, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_93, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_94, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_95, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_96, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_97, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_98, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_99, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_100, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_101, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_102, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_103, IO_TYPE_EXTERNAL),
> > + K1_FUNC_PIN(GPIO_104, IO_TYPE_3V3),
> > + K1_FUNC_PIN(GPIO_105, IO_TYPE_3V3),
> > + K1_FUNC_PIN(GPIO_106, IO_TYPE_3V3),
> > + K1_FUNC_PIN(GPIO_107, IO_TYPE_3V3),
> > + K1_FUNC_PIN(GPIO_108, IO_TYPE_3V3),
> > + K1_FUNC_PIN(GPIO_109, IO_TYPE_3V3),
> > + K1_FUNC_PIN(GPIO_110, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_111, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_112, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_113, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_114, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_115, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_116, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_117, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_118, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_119, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_120, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_121, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_122, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_123, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_124, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_125, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_126, IO_TYPE_1V8),
> > + K1_FUNC_PIN(GPIO_127, IO_TYPE_1V8),
> > +};
> > +
> > +static const struct spacemit_pinctrl_data k1_pinctrl_data = {
> > + .pins = k1_pin_desc,
> > + .data = k1_pin_data,
> > + .npins = ARRAY_SIZE(k1_pin_desc),
> > +};
> > +
> > +static const struct of_device_id k1_pinctrl_ids[] = {
> > + { .compatible = "spacemit,k1-pinctrl", .data = &k1_pinctrl_data },
> > + { /* sentinel */ }
> > +};
> > +MODULE_DEVICE_TABLE(of, k1_pinctrl_ids);
> > +
> > +static struct platform_driver k1_pinctrl_driver = {
> > + .probe = spacemit_pinctrl_probe,
> > + .driver = {
> > + .name = "k1-pinctrl",
> > + .suppress_bind_attrs = true,
> > + .of_match_table = k1_pinctrl_ids,
> > + },
> > +};
> > +module_platform_driver(k1_pinctrl_driver);
> > +
> > +MODULE_AUTHOR("Yixun Lan <dlan at gentoo.org>");
> > +MODULE_DESCRIPTION("Pinctrl driver for the SpacemiT K1 SoC");
> > +MODULE_LICENSE("GPL");
> > diff --git a/drivers/pinctrl/spacemit/pinctrl-k1.h b/drivers/pinctrl/spacemit/pinctrl-k1.h
> > new file mode 100644
> > index 0000000000000..9d6589b626e9d
> > --- /dev/null
> > +++ b/drivers/pinctrl/spacemit/pinctrl-k1.h
> > @@ -0,0 +1,36 @@
> > +/* SPDX-License-Identifier: GPL-2.0 */
> > +/* Copyright (c) 2024 Yixun Lan <dlan at gentoo.org> */
> > +
> > +#ifndef _PINCTRL_SPACEMIT_K1_H
> > +#define _PINCTRL_SPACEMIT_K1_H
> > +
> > +#include <linux/bits.h>
> > +#include <linux/bitfield.h>
> > +#include <linux/device.h>
> > +#include <linux/mutex.h>
> > +#include <linux/spinlock.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/pinctrl/pinctrl.h>
> > +#include <linux/pinctrl/pinconf.h>
> > +
> > +enum spacemit_pin_io_type {
> > + IO_TYPE_NONE = 0,
> > + IO_TYPE_1V8,
> > + IO_TYPE_3V3,
> > + IO_TYPE_EXTERNAL,
> > +};
> > +
> > +#define K1_PIN_IO_TYPE GENMASK(2, 1)
> > +
> > +#define K1_PIN_CAP_IO_TYPE(type) \
> > + FIELD_PREP_CONST(K1_PIN_IO_TYPE, type)
> > +#define K1_PIN_GET_IO_TYPE(val) \
> > + FIELD_GET(K1_PIN_IO_TYPE, val)
> > +
> > +#define K1_FUNC_PIN(_id, _io) \
> > + { \
> > + .pin = (_id), \
> > + .flags = (K1_PIN_CAP_IO_TYPE(_io)) \
> > + }
> > +
> > +#endif /* _PINCTRL_SPACEMIT_K1_H */
> >
> > --
> > 2.45.2
> >
--
Yixun Lan (dlan)
Gentoo Linux Developer
GPG Key ID AABEFD55
More information about the linux-riscv
mailing list