[PATCH 2/2] usb: dwc3: add T-HEAD TH1520 usb driver

[Jisheng Zhang]

Adds TH1520 Glue layer to support USB controller on T-HEAD TH1520 SoC.
There is a DesignWare USB3 DRD core in TH1520 SoCs, the dwc3 core is
the child of this USB wrapper module device.

Signed-off-by: Jisheng Zhang <jszhang at kernel.org>
---
 MAINTAINERS                   |   1 +
 drivers/usb/dwc3/Kconfig      |   9 +++
 drivers/usb/dwc3/Makefile     |   1 +
 drivers/usb/dwc3/dwc3-thead.c | 119 ++++++++++++++++++++++++++++++++++
 4 files changed, 130 insertions(+)
 create mode 100644 drivers/usb/dwc3/dwc3-thead.c

diff --git a/MAINTAINERS b/MAINTAINERS
index 90f13281d297..d55e40060c46 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -18481,6 +18481,7 @@ M:	Fu Wei <wefu at redhat.com>
 L:	linux-riscv at lists.infradead.org
 S:	Maintained
 F:	arch/riscv/boot/dts/thead/
+F:	drivers/usb/dwc3/dwc3-thead.c
 
 RNBD BLOCK DRIVERS
 M:	Md. Haris Iqbal <haris.iqbal at ionos.com>
diff --git a/drivers/usb/dwc3/Kconfig b/drivers/usb/dwc3/Kconfig
index 98efcbb76c88..1b02f4f55b47 100644
--- a/drivers/usb/dwc3/Kconfig
+++ b/drivers/usb/dwc3/Kconfig
@@ -178,4 +178,13 @@ config USB_DWC3_OCTEON
 	  Only the host mode is currently supported.
 	  Say 'Y' or 'M' here if you have one such device.
 
+config USB_DWC3_THEAD
+	tristate "T-HEAD Platform"
+	depends on ARCH_THEAD || COMPILE_TEST
+	default USB_DWC3
+	help
+	  Support T-HEAD platform with DesignWare Core USB3 IP.
+	  Only the host mode is currently supported.
+	  Say 'Y' or 'M' here if you have one such device.
+
 endif
diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
index fe1493d4bbe5..9523a51dd279 100644
--- a/drivers/usb/dwc3/Makefile
+++ b/drivers/usb/dwc3/Makefile
@@ -55,3 +55,4 @@ obj-$(CONFIG_USB_DWC3_QCOM)		+= dwc3-qcom.o
 obj-$(CONFIG_USB_DWC3_IMX8MP)		+= dwc3-imx8mp.o
 obj-$(CONFIG_USB_DWC3_XILINX)		+= dwc3-xilinx.o
 obj-$(CONFIG_USB_DWC3_OCTEON)		+= dwc3-octeon.o
+obj-$(CONFIG_USB_DWC3_THEAD)		+= dwc3-thead.o
diff --git a/drivers/usb/dwc3/dwc3-thead.c b/drivers/usb/dwc3/dwc3-thead.c
new file mode 100644
index 000000000000..999b1e319c72
--- /dev/null
+++ b/drivers/usb/dwc3/dwc3-thead.c
@@ -0,0 +1,119 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dwc3-thead.c - T-HEAD platform specific glue layer
+ *
+ * Inspired by dwc3-of-simple.c
+ *
+ * Copyright (C) 2021 Alibaba Group Holding Limited.
+ * Copyright (C) 2023 Jisheng Zhang <jszhang at kernel.org>
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "core.h"
+
+#define USB_SSP_EN		0x34
+#define  REF_SSP_EN		BIT(0)
+#define USB_SYS			0x3c
+#define  COMMONONN		BIT(0)
+
+#define USB3_DRD_SWRST		0x14
+#define  USB3_DRD_PRST		BIT(0)
+#define  USB3_DRD_PHYRST	BIT(1)
+#define  USB3_DRD_VCCRST	BIT(2)
+#define  USB3_DRD_RSTMASK	(USB3_DRD_PRST | USB3_DRD_PHYRST | USB3_DRD_VCCRST)
+
+struct dwc3_thead {
+	void __iomem		*base;
+	struct regmap		*misc_sysreg;
+	struct regulator	*vbus;
+};
+
+static void dwc3_thead_optimize_power(struct dwc3_thead *thead)
+{
+	u32 val;
+
+	/* config usb top within USB ctrl & PHY reset */
+	regmap_update_bits(thead->misc_sysreg, USB3_DRD_SWRST,
+			   USB3_DRD_RSTMASK, USB3_DRD_PRST);
+
+	/*
+	 * dwc reg also need to be configed to save power
+	 * 1. set USB_SYS[COMMONONN]
+	 * 2. set DWC3_GCTL[SOFITPSYNC](done by core.c)
+	 * 3. set GUSB3PIPECTL[SUSPENDEN] (done by core.c)
+	 */
+	val = readl(thead->base + USB_SYS);
+	val |= COMMONONN;
+	writel(val, thead->base + USB_SYS);
+	val = readl(thead->base + USB_SSP_EN);
+	val |= REF_SSP_EN;
+	writel(val, thead->base + USB_SSP_EN);
+
+	regmap_update_bits(thead->misc_sysreg, USB3_DRD_SWRST,
+			   USB3_DRD_RSTMASK, USB3_DRD_RSTMASK);
+}
+
+static int dwc3_thead_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct dwc3_thead *thead;
+	int ret;
+
+	thead = devm_kzalloc(&pdev->dev, sizeof(*thead), GFP_KERNEL);
+	if (!thead)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, thead);
+
+	ret = devm_regulator_get_enable_optional(dev, "vbus");
+	if (ret < 0 && ret != -ENODEV)
+		return ret;
+
+	thead->misc_sysreg = syscon_regmap_lookup_by_phandle(np, "thead,misc-sysreg");
+	if (IS_ERR(thead->misc_sysreg))
+		return PTR_ERR(thead->misc_sysreg);
+
+	thead->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(thead->base))
+		return PTR_ERR(thead->base);
+
+	dwc3_thead_optimize_power(thead);
+
+	return of_platform_populate(np, NULL, NULL, dev);
+}
+
+static void dwc3_thead_remove(struct platform_device *pdev)
+{
+	of_platform_depopulate(&pdev->dev);
+}
+
+static const struct of_device_id dwc3_thead_of_match[] = {
+	{ .compatible = "thead,th1520-usb" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, dwc3_thead_of_match);
+
+static struct platform_driver dwc3_thead_driver = {
+	.probe		= dwc3_thead_probe,
+	.remove_new	= dwc3_thead_remove,
+	.driver		= {
+		.name	= "dwc3-thead",
+		.of_match_table	= dwc3_thead_of_match,
+	},
+};
+module_platform_driver(dwc3_thead_driver);
+
+MODULE_ALIAS("platform:dwc3-thead");
+MODULE_LICENSE("GPL v2");
+MODULE_DESCRIPTION("DesignWare DWC3 T-HEAD Glue Driver");
+MODULE_AUTHOR("Jisheng Zhang <jszhang at kernel.org>");
-- 
2.40.1