[PATCH v9 19/20] PCI: starfive: Add JH7110 PCIe controller

Bjorn Helgaas helgaas at kernel.org
Tue Oct 24 10:52:53 PDT 2023


On Fri, Oct 20, 2023 at 06:43:40PM +0800, Minda Chen wrote:
> Add StarFive JH7110 SoC PCIe controller platform
> driver codes, JH7110 with PLDA host PCIe core.

Wrap all your commit logs to fill about 75 columns (as suggested
before).  "git log" adds a few spaces, so if you fill to 75 columns,
the result will still fit in a default 80 column window.

> +config PCIE_STARFIVE_HOST
> +	tristate "StarFive PCIe host controller"
> +	depends on OF && PCI_MSI
> +	select PCIE_PLDA_HOST
> +	help
> +	  Say Y here if you want to support the StarFive PCIe controller
> +	  in host mode. StarFive PCIe controller uses PLDA PCIe
> +	  core.

Add blank line between paragraphs.  Wrap to fill 75-78 columns.

> +	  If you choose to build this driver as module it will
> +	  be dynamically linked and module will be called
> +	  pcie-starfive.ko

> +++ b/drivers/pci/controller/plda/pcie-plda.h
> @@ -6,14 +6,26 @@
>  #ifndef _PCIE_PLDA_H
>  #define _PCIE_PLDA_H
>  
> +#include <linux/phy/phy.h>

I don't think you need to #include this.  In this file you only use a
pointer to struct phy, so declaring the struct should be enough, e.g.,

  struct phy;

You will have to #include it in pcie-starfive.c where you actually
*use* phy, of course.

> +#define CONFIG_SPACE_ADDR			0x1000u

This looks like an *offset* that you add to ->bridge_addr.  Adding two
addresses together doesn't really make sense.

> +static int starfive_pcie_config_write(struct pci_bus *bus, unsigned int devfn,
> +				      int where, int size, u32 value)
> +{
> +	if (starfive_pcie_hide_rc_bar(bus, devfn, where))
> +		return PCIBIOS_BAD_REGISTER_NUMBER;

I think this should probably return PCIBIOS_SUCCESSFUL.  There's
nothing wrong with the register number; you just want to pretend that
it's hardwired to zero.  That means ignore writes and always return 0
for reads.

> +	return pci_generic_config_write(bus, devfn, where, size, value);
> +}
> +
> +static int starfive_pcie_config_read(struct pci_bus *bus, unsigned int devfn,
> +				     int where, int size, u32 *value)
> +{
> +	if (starfive_pcie_hide_rc_bar(bus, devfn, where))
> +		return PCIBIOS_BAD_REGISTER_NUMBER;

Set *value to zero and return PCIBIOS_SUCCESSFUL.

> +	return pci_generic_config_read(bus, devfn, where, size, value);
> +}
> +
> +static int starfive_pcie_parse_dt(struct starfive_jh7110_pcie *pcie, struct device *dev)

95% of this driver (and the rest of drivers/pci) is wrapped to fit in
80 columns, e.g.,

  static int starfive_pcie_parse_dt(struct starfive_jh7110_pcie *pcie,
                                    struct device *dev)

> +	domain_nr = of_get_pci_domain_nr(dev->of_node);
> +
> +	if (domain_nr < 0 || domain_nr > 1)
> +		return dev_err_probe(dev, -ENODEV,
> +				     "failed to get valid pcie id\n");

"id" is too generic and doesn't hint about where the problem is.
Update the message ("pcie id") to mention "domain" so it corresponds
with the source ("linux,pci-domain" from DT).

> +	ret = reset_control_deassert(pcie->resets);
> +	if (ret) {
> +		clk_bulk_disable_unprepare(pcie->num_clks, pcie->clks);
> +		dev_err_probe(dev, ret, "failed to resets\n");

"failed to ... resets" is missing a word.  "Failed to deassert
resets", I guess?

> +	/* Ensure that PERST has been asserted for at least 100 ms,
> +	 * the sleep value is T_PVPERL from PCIe CEM spec r2.0 (Table 2-4)
> +	 */

Use multiline comment formatting (also below):

  /*
   * Ensure ...
   */

> +	msleep(100);
> +	if (pcie->reset_gpio)
> +		gpiod_set_value_cansleep(pcie->reset_gpio, 0);
> +
> +	/* As the requirement in PCIe base spec r6.0, system (<=5GT/s) must
> +	 * wait a minimum of 100 ms following exit from a conventional reset
> +	 * before sending a configuration request to the device.

Mention sec 6.6.1, where (I think) this value comes from.  Eventually
we should make a #define for this because it's not specific to any one
PCIe controller.

> +	msleep(100);
> +
> +	if (starfive_pcie_host_wait_for_link(pcie))
> +		dev_info(dev, "port link down\n");
> +
> +	return ret;

We know the value here, so return it explicitly:

  return 0;

> +static int starfive_pcie_suspend_noirq(struct device *dev)
> +{
> +	struct starfive_jh7110_pcie *pcie = dev_get_drvdata(dev);
> +
> +	if (!pcie)
> +		return 0;

How could it happen that "pcie" is zero?  I think it could only happen
if there were a driver bug or a memory corruption.  Either way, we
should remove the check so we take a NULL pointer fault and find out
about the problem.

> +static int starfive_pcie_resume_noirq(struct device *dev)
> +{
> +	struct starfive_jh7110_pcie *pcie = dev_get_drvdata(dev);
> +	int ret;
> +
> +	ret = starfive_pcie_enable_phy(dev, &pcie->plda);
> +	if (ret)
> +		return ret;
> +
> +	ret = clk_bulk_prepare_enable(pcie->num_clks, pcie->clks);
> +	if (ret) {
> +		dev_err(dev, "failed to enable clocks\n");
> +		starfive_pcie_disable_phy(&pcie->plda);
> +		return ret;
> +	}
> +
> +	return ret;

  return 0;

Bjorn



More information about the linux-riscv mailing list