[PATCH 3/6] mmc: sdhci-of-dwcmshc: Add support for T-Head TH1520
Jisheng Zhang
jszhang at kernel.org
Wed Oct 4 09:19:03 PDT 2023
On Thu, Sep 21, 2023 at 06:49:50PM -0700, Drew Fustini wrote:
> Add support for the mmc controller in the T-Head TH1520 with the new
> compatible "thead,th1520-dwcmshc". Implement custom sdhci_ops for
> set_uhs_signaling, reset, voltage_switch, and platform_execute_tuning.
>
> Signed-off-by: Drew Fustini <dfustini at baylibre.com>
Hi Drew,
Thanks for doing this and sorry for being late for this code review. Some
comments below.
> ---
> drivers/mmc/host/sdhci-of-dwcmshc.c | 456 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 456 insertions(+)
>
> diff --git a/drivers/mmc/host/sdhci-of-dwcmshc.c b/drivers/mmc/host/sdhci-of-dwcmshc.c
> index 3a3bae6948a8..7294bf1afb7d 100644
> --- a/drivers/mmc/host/sdhci-of-dwcmshc.c
> +++ b/drivers/mmc/host/sdhci-of-dwcmshc.c
> @@ -35,6 +35,26 @@
> #define DWCMSHC_CARD_IS_EMMC BIT(0)
> #define DWCMSHC_ENHANCED_STROBE BIT(8)
> #define DWCMSHC_EMMC_ATCTRL 0x40
> +/* Tuning and auto-tuning fields in AT_CTRL_R control register */
> +#define AT_CTRL_AT_EN 0x1 /* autotuning is enabled */
> +#define AT_CTRL_CI_SEL_SHIFT 0x1 /* bit 1 */
> +#define AT_CTRL_CI_SEL 0x1 /* interval to drive center phase select */
> +#define AT_CTRL_SWIN_TH_EN_SHIFT 0x2 /* bit 2 */
> +#define AT_CTRL_SWIN_TH_EN 0x1 /* sampling window threshold enable */
> +#define AT_CTRL_RPT_TUNE_ERR_SHIFT 0x3 /* bit 3 */
> +#define AT_CTRL_RPT_TUNE_ERR 0x1 /* enable reporting framing errors */
> +#define AT_CTRL_SW_TUNE_EN_SHIFT 0x4 /* bit 4 */
> +#define AT_CTRL_SW_TUNE_EN 0x1 /* enable software managed tuning */
> +#define AT_CTRL_WIN_EDGE_SEL_SHIFT 0x8 /* bits [11:8] */
> +#define AT_CTRL_WIN_EDGE_SEL 0xf /* sampling window edge select */
> +#define AT_CTRL_TUNE_CLK_STOP_EN_SHIFT 0x10 /* bit 16 */
> +#define AT_CTRL_TUNE_CLK_STOP_EN 0x1 /* clocks stopped during phase code change */
> +#define AT_CTRL_PRE_CHANGE_DLY_SHIFT 0x11 /* bits [18:17] */
> +#define AT_CTRL_PRE_CHANGE_DLY 0x1 /* 2-cycle latency */
> +#define AT_CTRL_POST_CHANGE_DLY_SHIFT 0x13 /* bits [20:19] */
> +#define AT_CTRL_POST_CHANGE_DLY 0x3 /* 4-cycle latency */
> +#define AT_CTRL_SWIN_TH_VAL_SHIFT 0x18 /* bits [31:24] */
> +#define AT_CTRL_SWIN_TH_VAL 0x9 /* sampling window threshold */
>
> /* Rockchip specific Registers */
> #define DWCMSHC_EMMC_DLL_CTRL 0x800
> @@ -72,6 +92,84 @@
> (((x) & DWCMSHC_EMMC_DLL_TIMEOUT) == 0))
> #define RK35xx_MAX_CLKS 3
>
> +/* PHY register area pointer */
> +#define DWC_MSHC_PTR_PHY_R 0x300
> +
> +/* PHY general configuration */
> +#define PHY_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x00)
> +#define PHY_CNFG_RSTN_DEASSERT 0x1 /* Deassert PHY reset */
> +#define PHY_CNFG_PAD_SP_SHIFT 0x10 /* bits [16:9] */
> +#define PHY_CNFG_PAD_SP_VALUE 0x0c /* PMOS TX drive strength */
> +#define PHY_CNFG_PAD_SN_SHIFT 0x14 /* bits [23:20] */
> +#define PHY_CNFG_PAD_SN_VALUE 0x0c /* NMOS TX drive strength */
> +
> +/* PHY command/response pad settings */
> +#define PHY_CMDPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x04)
> +
> +/* PHY data pad settings */
> +#define PHY_DATAPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x06)
> +
> +/* PHY clock pad settings */
> +#define PHY_CLKPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x08)
> +
> +/* PHY strobe pad settings */
> +#define PHY_STBPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x0a)
> +
> +/* PHY reset pad settings */
> +#define PHY_RSTNPAD_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x0c)
> +
> +/* Bitfields are common for all pad settings */
> +#define PHY_PAD_RXSEL_1V8 0x1 /* Receiver type select for 1.8V */
> +#define PHY_PAD_RXSEL_3V3 0x2 /* Receiver type select for 3.3V */
> +
> +#define PHY_PAD_WEAKPULL_SHIFT 0x3 /* bits [4:3] */
> +#define PHY_PAD_WEAKPULL_PULLUP 0x1 /* Weak pull down enabled */
> +#define PHY_PAD_WEAKPULL_PULLDOWN 0x2 /* Weak pull down enabled */
> +
> +#define PHY_PAD_TXSLEW_CTRL_P_SHIFT 0x5 /* bits [8:5] */
> +#define PHY_PAD_TXSLEW_CTRL_P_VALUE 0x3 /* Slew control for P-Type pad TX */
> +#define PHY_PAD_TXSLEW_CTRL_N_SHIFT 0x9 /* bits [12:9] */
> +#define PHY_PAD_TXSLEW_CTRL_N_VALUE 0x3 /* Slew control for N-Type pad TX */
> +
> +/* PHY CLK delay line settings */
> +#define PHY_SDCLKDL_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x1d)
> +#define PHY_SDCLKDL_CNFG_UPDATE_SHIFT 0x4 /* bit 4 */
> +#define PHY_SDCLKDL_CNFG_UPDATE_DC 0x1 /* set before writing to SDCLKDL_DC */
> +
> +/* PHY CLK delay line delay code */
> +#define PHY_SDCLKDL_DC_R (DWC_MSHC_PTR_PHY_R + 0x1e)
> +#define PHY_SDCLKDL_DC_INITIAL 0x40 /* initial delay code */
> +#define PHY_SDCLKDL_DC_DEFAULT 0x32 /* default delay code */
> +#define PHY_SDCLKDL_DC_HS400 0x18 /* delay code for HS400 mode */
> +
> +/* PHY drift_cclk_rx delay line configuration setting */
> +#define PHY_ATDL_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x21)
> +#define PHY_ATDL_CNFG_INPSEL_SHIFT 0x2 /* bits [3:2] */
> +#define PHY_ATDL_CNFG_INPSEL_VALUE 0x3 /* delay line input source */
> +
> +/* PHY DLL control settings */
> +#define PHY_DLL_CTRL_R (DWC_MSHC_PTR_PHY_R + 0x24)
> +#define PHY_DLL_CTRL_DISABLE 0x0 /* PHY DLL is enabled */
> +#define PHY_DLL_CTRL_ENABLE 0x1 /* PHY DLL is disabled */
> +
> +/* PHY DLL configuration register 1 */
> +#define PHY_DLL_CNFG1_R (DWC_MSHC_PTR_PHY_R + 0x25)
> +#define PHY_DLL_CNFG1_SLVDLY_SHIFT 0x4 /* bits [5:4] */
> +#define PHY_DLL_CNFG1_SLVDLY_VALUE 0x2 /* DLL slave update delay input */
> +#define PHY_DLL_CNFG1_WAITCYCLE 0x5 /* DLL wait cycle input */
> +
> +/* PHY DLL configuration register 2 */
> +#define PHY_DLL_CNFG2_R (DWC_MSHC_PTR_PHY_R + 0x26)
> +#define PHY_DLL_CNFG2_JUMPSTEP 0xa /* DLL jump step input */
> +
> +/* PHY DLL master and slave delay line configuration settings */
> +#define PHY_DLLDL_CNFG_R (DWC_MSHC_PTR_PHY_R + 0x28)
> +#define PHY_DLLDL_CNFG_SLV_INPSEL_SHIFT 0x5 /* bits [6:5] */
> +#define PHY_DLLDL_CNFG_SLV_INPSEL_VALUE 0x3 /* clock source select for slave DL */
> +
> +#define FLAG_PULL_UP_EN BIT(0)
> +#define FLAG_IO_FIXED_1V8 BIT(1)
> +
> #define BOUNDARY_OK(addr, len) \
> ((addr | (SZ_128M - 1)) == ((addr + len - 1) | (SZ_128M - 1)))
>
> @@ -92,6 +190,8 @@ struct dwcmshc_priv {
> struct clk *bus_clk;
> int vendor_specific_area1; /* P_VENDOR_SPECIFIC_AREA reg */
> void *priv; /* pointer to SoC private stuff */
> + u16 delay_line;
> + u16 flags;
> };
>
> /*
> @@ -157,6 +257,206 @@ static void dwcmshc_request(struct mmc_host *mmc, struct mmc_request *mrq)
> sdhci_request(mmc, mrq);
> }
>
> +static void th1520_phy_1_8v_init_no_pull(struct sdhci_host *host)
> +{
> + u32 val;
> +
> + /* deassert phy reset */
> + sdhci_writel(host, PHY_CNFG_RSTN_DEASSERT, PHY_CNFG_R);
> +
> + /* disable delay line */
> + sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT,
> + PHY_SDCLKDL_CNFG_R);
> +
> + /* set delay line */
> + sdhci_writeb(host, PHY_SDCLKDL_DC_INITIAL, PHY_SDCLKDL_DC_R);
> +
> + /* enable delay lane */
> + val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R);
> + val &= ~(PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT);
> + sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R);
> +
> + /* configure phy pads */
> + val = sdhci_readw(host, PHY_CMDPAD_CNFG_R);
> + sdhci_writew(host, val | PHY_PAD_RXSEL_1V8, PHY_CMDPAD_CNFG_R);
> +
> + val = sdhci_readw(host, PHY_DATAPAD_CNFG_R);
> + sdhci_writew(host, val | PHY_PAD_RXSEL_1V8, PHY_DATAPAD_CNFG_R);
> +
> + val = sdhci_readw(host, PHY_RSTNPAD_CNFG_R);
> + sdhci_writew(host, val | PHY_PAD_RXSEL_1V8, PHY_RSTNPAD_CNFG_R);
> +
> + val = sdhci_readw(host, PHY_STBPAD_CNFG_R);
> + sdhci_writew(host, val | PHY_PAD_RXSEL_1V8, PHY_STBPAD_CNFG_R);
> +
> + /* enable phy dll */
> + val = sdhci_readb(host, PHY_DLL_CTRL_R);
> + sdhci_writeb(host, val | PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R);
> +}
> +
> +static void th1520_phy_3_3v_init_no_pull(struct sdhci_host *host)
> +{
> + u32 val;
> +
> + /* deassert phy reset */
> + sdhci_writel(host, PHY_CNFG_RSTN_DEASSERT, PHY_CNFG_R);
> +
> + /* disable delay line */
> + sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT,
> + PHY_SDCLKDL_CNFG_R);
> +
> + /* set delay line */
> + sdhci_writeb(host, PHY_SDCLKDL_DC_INITIAL, PHY_SDCLKDL_DC_R);
> +
> + /* enable delay lane */
> + val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R);
> + val &= ~(PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT);
> + sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R);
> +
> + /* configure phy pads */
> + val = sdhci_readw(host, PHY_CMDPAD_CNFG_R);
> + sdhci_writew(host, val | PHY_PAD_RXSEL_3V3, PHY_CMDPAD_CNFG_R);
> +
> + val = sdhci_readw(host, PHY_DATAPAD_CNFG_R);
> + sdhci_writew(host, val | PHY_PAD_RXSEL_3V3, PHY_DATAPAD_CNFG_R);
> +
> + val = sdhci_readw(host, PHY_RSTNPAD_CNFG_R);
> + sdhci_writew(host, val | PHY_PAD_RXSEL_3V3, PHY_RSTNPAD_CNFG_R);
> +
> + val = sdhci_readw(host, PHY_STBPAD_CNFG_R);
> + sdhci_writew(host, val | PHY_PAD_RXSEL_3V3, PHY_STBPAD_CNFG_R);
> +
> + /* enable phy dll */
> + val = sdhci_readb(host, PHY_DLL_CTRL_R);
> + sdhci_writeb(host, val | PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R);
> +}
> +
> +static void th1520_phy_1_8v_init(struct sdhci_host *host)
> +{
> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> + u32 val;
> +
> + if (!priv)
> + return;
> +
> + if (!(priv->flags & FLAG_PULL_UP_EN)) {
> + th1520_phy_1_8v_init_no_pull(host);
> + return;
> + }
> +
> + /* deassert phy reset & set tx drive strength */
> + sdhci_writel(host, PHY_CNFG_RSTN_DEASSERT |
> + (PHY_CNFG_PAD_SP_VALUE << PHY_CNFG_PAD_SP_SHIFT) |
> + (PHY_CNFG_PAD_SN_VALUE << PHY_CNFG_PAD_SN_SHIFT),
> + PHY_CNFG_R);
> +
> + /* disable delay line */
> + sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT,
> + PHY_SDCLKDL_CNFG_R);
> +
> + /* set delay line */
> + sdhci_writeb(host, priv->delay_line, PHY_SDCLKDL_DC_R);
> + sdhci_writeb(host, PHY_DLL_CNFG2_JUMPSTEP, PHY_DLL_CNFG2_R);
> +
> + /* enable delay lane */
> + val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R);
> + val &= ~(PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT);
> + sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R);
> +
> + /* configure phy pads */
> + val = PHY_PAD_RXSEL_1V8 | (PHY_PAD_WEAKPULL_PULLUP << PHY_PAD_WEAKPULL_SHIFT) |
> + (PHY_PAD_TXSLEW_CTRL_P_VALUE << PHY_PAD_TXSLEW_CTRL_P_SHIFT) |
> + (PHY_PAD_TXSLEW_CTRL_N_VALUE << PHY_PAD_TXSLEW_CTRL_N_SHIFT);
> + sdhci_writew(host, val, PHY_CMDPAD_CNFG_R);
> + sdhci_writew(host, val, PHY_DATAPAD_CNFG_R);
> + sdhci_writew(host, val, PHY_RSTNPAD_CNFG_R);
> +
> + val = (PHY_PAD_TXSLEW_CTRL_P_VALUE << PHY_PAD_TXSLEW_CTRL_P_SHIFT) |
> + (PHY_PAD_TXSLEW_CTRL_N_VALUE << PHY_PAD_TXSLEW_CTRL_N_SHIFT);
> + sdhci_writew(host, val, PHY_CLKPAD_CNFG_R);
> +
> + val = PHY_PAD_RXSEL_1V8 | (PHY_PAD_WEAKPULL_PULLDOWN << PHY_PAD_WEAKPULL_SHIFT) |
> + (PHY_PAD_TXSLEW_CTRL_P_VALUE << PHY_PAD_TXSLEW_CTRL_P_SHIFT) |
> + (PHY_PAD_TXSLEW_CTRL_N_VALUE << PHY_PAD_TXSLEW_CTRL_N_SHIFT);
> + sdhci_writew(host, val, PHY_STBPAD_CNFG_R);
> +
> + /* enable data strobe mode */
> + sdhci_writeb(host, PHY_DLLDL_CNFG_SLV_INPSEL_VALUE << PHY_DLLDL_CNFG_SLV_INPSEL_SHIFT,
> + PHY_DLLDL_CNFG_R);
> +
> + /* enable phy dll */
> + sdhci_writeb(host, PHY_DLL_CTRL_ENABLE, PHY_DLL_CTRL_R);
> +}
> +
> +static void th1520_phy_3_3v_init(struct sdhci_host *host)
> +{
> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> + u32 val;
> +
> + if (!(priv->flags & FLAG_PULL_UP_EN)) {
> + th1520_phy_3_3v_init_no_pull(host);
> + return;
> + }
> +
> + /* deassert phy reset & set tx drive strength */
> + sdhci_writel(host, PHY_CNFG_RSTN_DEASSERT |
> + (PHY_CNFG_PAD_SP_VALUE << PHY_CNFG_PAD_SP_SHIFT) |
> + (PHY_CNFG_PAD_SN_VALUE << PHY_CNFG_PAD_SN_SHIFT),
> + PHY_CNFG_R);
> +
> + /* disable delay line */
> + sdhci_writeb(host, PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT,
> + PHY_SDCLKDL_CNFG_R);
> +
> + /* set delay line */
> + sdhci_writeb(host, priv->delay_line, PHY_SDCLKDL_DC_R);
> + sdhci_writeb(host, PHY_DLL_CNFG2_JUMPSTEP, PHY_DLL_CNFG2_R);
> +
> + /* enable delay lane */
> + val = sdhci_readb(host, PHY_SDCLKDL_CNFG_R);
> + val &= ~(PHY_SDCLKDL_CNFG_UPDATE_DC << PHY_SDCLKDL_CNFG_UPDATE_SHIFT);
> + sdhci_writeb(host, val, PHY_SDCLKDL_CNFG_R);
> +
> + /* configure phy pads */
> + val = PHY_PAD_RXSEL_3V3 | (PHY_PAD_WEAKPULL_PULLUP << PHY_PAD_WEAKPULL_SHIFT) |
> + (PHY_PAD_TXSLEW_CTRL_P_VALUE << PHY_PAD_TXSLEW_CTRL_P_SHIFT) |
> + (PHY_PAD_TXSLEW_CTRL_N_VALUE << PHY_PAD_TXSLEW_CTRL_N_SHIFT);
> + sdhci_writew(host, val, PHY_CMDPAD_CNFG_R);
> + sdhci_writew(host, val, PHY_DATAPAD_CNFG_R);
> + sdhci_writew(host, val, PHY_RSTNPAD_CNFG_R);
> +
> + val = (PHY_PAD_TXSLEW_CTRL_P_VALUE << PHY_PAD_TXSLEW_CTRL_P_SHIFT) |
> + (PHY_PAD_TXSLEW_CTRL_N_VALUE << PHY_PAD_TXSLEW_CTRL_N_SHIFT);
> + sdhci_writew(host, val, PHY_CLKPAD_CNFG_R);
> +
> + val = PHY_PAD_RXSEL_3V3 | (PHY_PAD_WEAKPULL_PULLDOWN << PHY_PAD_WEAKPULL_SHIFT) |
> + (PHY_PAD_TXSLEW_CTRL_P_VALUE << PHY_PAD_TXSLEW_CTRL_P_SHIFT) |
> + (PHY_PAD_TXSLEW_CTRL_N_VALUE << PHY_PAD_TXSLEW_CTRL_N_SHIFT);
> + sdhci_writew(host, val, PHY_STBPAD_CNFG_R);
> +}
> +
> +static void th1520_sdhci_set_phy(struct sdhci_host *host)
> +{
> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> + u16 emmc_ctrl;
> +
> + /* Before power on, set PHY configs */
> + if (host->mmc->caps & MMC_CAP_NONREMOVABLE) {
check flag & FLAG_IO_FIXED_1V8 instead? Because I didn't see why
3.3v can't be non-removeable. I know you only brought up emmc
now, but we can also prepare for sdio/sd support at the same time.
> + th1520_phy_1_8v_init(host);
> + emmc_ctrl = sdhci_readw(host, priv->vendor_specific_area1 + DWCMSHC_EMMC_CONTROL);
> + emmc_ctrl |= DWCMSHC_CARD_IS_EMMC;
can we check host->mmc->caps2 to know whether this is eMMC or not, then
set this bit for eMMC after that.
And setting DWCMSHC_CARD_IS_EMMC should be orthogonalized with 3.3v/1.8v
etc.
> + sdhci_writew(host, emmc_ctrl, priv->vendor_specific_area1 + DWCMSHC_EMMC_CONTROL);
> + } else {
> + th1520_phy_3_3v_init(host);
> + }
> +
> + sdhci_writeb(host, (PHY_DLL_CNFG1_SLVDLY_VALUE << PHY_DLL_CNFG1_SLVDLY_SHIFT) |
I'm not sure whether we need to get the delay value from DT.
Do emmc, sd and sdio share the same delay value?
> + PHY_DLL_CNFG1_WAITCYCLE, PHY_DLL_CNFG1_R);
> +}
> +
> static void dwcmshc_set_uhs_signaling(struct sdhci_host *host,
> unsigned int timing)
> {
> @@ -189,9 +489,30 @@ static void dwcmshc_set_uhs_signaling(struct sdhci_host *host,
> ctrl_2 |= DWCMSHC_CTRL_HS400;
> }
>
> + if (priv->flags & FLAG_IO_FIXED_1V8)
> + ctrl_2 |= SDHCI_CTRL_VDD_180;
> sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
> }
>
> +static void th1520_set_uhs_signaling(struct sdhci_host *host,
> + unsigned int timing)
> +{
> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> + u32 reg;
> +
> + dwcmshc_set_uhs_signaling(host, timing);
> + if (timing == MMC_TIMING_MMC_HS400) {
> + reg = sdhci_readl(host, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);
> + reg &= ~AT_CTRL_AT_EN;
> + sdhci_writel(host, reg, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);
can we move the auto tuning bit setting to tuning routine?
> + priv->delay_line = PHY_SDCLKDL_DC_HS400;
this delay line may need to be gotten from DT?
> + th1520_sdhci_set_phy(host);
> + } else {
> + sdhci_writeb(host, 0, PHY_DLLDL_CNFG_R);
> + }
> +}
> +
> static void dwcmshc_hs400_enhanced_strobe(struct mmc_host *mmc,
> struct mmc_ios *ios)
> {
> @@ -338,6 +659,91 @@ static void rk35xx_sdhci_reset(struct sdhci_host *host, u8 mask)
> sdhci_reset(host, mask);
> }
>
> +static int th1520_execute_tuning(struct sdhci_host *host, u32 opcode)
> +{
> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> + u32 val = 0;
> +
> + if (host->flags & SDHCI_HS400_TUNING)
> + return 0;
> +
> + sdhci_writeb(host, PHY_ATDL_CNFG_INPSEL_VALUE << PHY_ATDL_CNFG_INPSEL_SHIFT,
> + PHY_ATDL_CNFG_R);
> + val = sdhci_readl(host, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);
> +
> + /*
> + * configure tuning settings:
> + * - center phase select code driven in block gap interval
> + * - disable reporting of framing errors
> + * - disable software managed tuning
> + * - disable user selection of sampling window edges,
> + * instead tuning calculated edges are used
> + */
> + val &= ~((AT_CTRL_CI_SEL << AT_CTRL_CI_SEL_SHIFT) |
> + (AT_CTRL_RPT_TUNE_ERR << AT_CTRL_RPT_TUNE_ERR_SHIFT) |
> + (AT_CTRL_SW_TUNE_EN << AT_CTRL_SW_TUNE_EN_SHIFT) |
> + (AT_CTRL_WIN_EDGE_SEL << AT_CTRL_WIN_EDGE_SEL_SHIFT));
> +
> + /*
> + * configure tuning settings:
> + * - enable auto-tuning
> + * - enable sampling window threshold
> + * - stop clocks during phase code change
> + * - set max latency in cycles between tx and rx clocks
> + * - set max latency in cycles to switch output phase
> + * - set max sampling window threshold value
> + */
> + val |= AT_CTRL_AT_EN | (AT_CTRL_SWIN_TH_EN << AT_CTRL_SWIN_TH_EN_SHIFT) |
> + (AT_CTRL_TUNE_CLK_STOP_EN << AT_CTRL_TUNE_CLK_STOP_EN_SHIFT) |
> + (AT_CTRL_PRE_CHANGE_DLY << AT_CTRL_PRE_CHANGE_DLY_SHIFT) |
> + (AT_CTRL_POST_CHANGE_DLY << AT_CTRL_POST_CHANGE_DLY_SHIFT) |
> + (AT_CTRL_SWIN_TH_VAL << AT_CTRL_SWIN_TH_VAL_SHIFT);
> +
> + sdhci_writel(host, val, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);
> + val = sdhci_readl(host, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);
> +
> + /* check if is possible to enable auto-tuning */
> + if (!(val & AT_CTRL_AT_EN)) {
> + dev_err(mmc_dev(host->mmc), "failed to enable auto tuning\n");
> + return -EIO;
> + }
> +
> + /* disable auto tuning */
> + val &= ~AT_CTRL_AT_EN;
> + sdhci_writel(host, val, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);
AFAIK, the HW support auto tuning, can we enable it?
> +
> + /* perform tuning */
> + sdhci_start_tuning(host);
> + host->tuning_err = __sdhci_execute_tuning(host, opcode);
> + if (host->tuning_err) {
> + val &= ~AT_CTRL_AT_EN;
It looks like auto tunning is never enabled, so why do clear it here?
> + sdhci_writel(host, val, priv->vendor_specific_area1 + DWCMSHC_EMMC_ATCTRL);
> + dev_err(mmc_dev(host->mmc), "tuning failed: %d\n", host->tuning_err);
> + return -EIO;
> + }
> + sdhci_end_tuning(host);
> +
> + return 0;
> +}
> +
> +static void th1520_sdhci_reset(struct sdhci_host *host, u8 mask)
> +{
> + struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
> + struct dwcmshc_priv *priv = sdhci_pltfm_priv(pltfm_host);
> + u16 ctrl_2;
> +
> + sdhci_reset(host, mask);
> +
> + if (priv->flags & FLAG_IO_FIXED_1V8) {
> + ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
> + if (!(ctrl_2 & SDHCI_CTRL_VDD_180)) {
> + ctrl_2 |= SDHCI_CTRL_VDD_180;
> + sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
> + }
> + }
> +}
> +
> static const struct sdhci_ops sdhci_dwcmshc_ops = {
> .set_clock = sdhci_set_clock,
> .set_bus_width = sdhci_set_bus_width,
> @@ -356,6 +762,17 @@ static const struct sdhci_ops sdhci_dwcmshc_rk35xx_ops = {
> .adma_write_desc = dwcmshc_adma_write_desc,
> };
>
> +static const struct sdhci_ops sdhci_dwcmshc_th1520_ops = {
> + .set_clock = sdhci_set_clock,
> + .set_bus_width = sdhci_set_bus_width,
> + .set_uhs_signaling = th1520_set_uhs_signaling,
> + .get_max_clock = dwcmshc_get_max_clock,
> + .reset = th1520_sdhci_reset,
> + .adma_write_desc = dwcmshc_adma_write_desc,
> + .voltage_switch = th1520_phy_1_8v_init,
> + .platform_execute_tuning = &th1520_execute_tuning,
> +};
> +
> static const struct sdhci_pltfm_data sdhci_dwcmshc_pdata = {
> .ops = &sdhci_dwcmshc_ops,
> .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
> @@ -379,6 +796,12 @@ static const struct sdhci_pltfm_data sdhci_dwcmshc_rk35xx_pdata = {
> SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN,
> };
>
> +static const struct sdhci_pltfm_data sdhci_dwcmshc_th1520_pdata = {
> + .ops = &sdhci_dwcmshc_th1520_ops,
> + .quirks = SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
> + .quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN,
> +};
> +
> static int dwcmshc_rk35xx_init(struct sdhci_host *host, struct dwcmshc_priv *dwc_priv)
> {
> int err;
> @@ -447,6 +870,10 @@ static const struct of_device_id sdhci_dwcmshc_dt_ids[] = {
> .compatible = "snps,dwcmshc-sdhci",
> .data = &sdhci_dwcmshc_pdata,
> },
> + {
> + .compatible = "thead,th1520-dwcmshc",
> + .data = &sdhci_dwcmshc_th1520_pdata,
> + },
> {},
> };
> MODULE_DEVICE_TABLE(of, sdhci_dwcmshc_dt_ids);
> @@ -542,6 +969,35 @@ static int dwcmshc_probe(struct platform_device *pdev)
> goto err_clk;
> }
>
> + if (pltfm_data == &sdhci_dwcmshc_th1520_pdata) {
> + priv->delay_line = PHY_SDCLKDL_DC_DEFAULT;
Ditto.
> +
> + if (device_property_present(&pdev->dev, "thead,phy-pull-up"))
> + priv->flags |= FLAG_PULL_UP_EN;
> + else
> + priv->flags &= ~FLAG_PULL_UP_EN;
> +
> + if ((device_property_read_bool(dev, "mmc-ddr-1_8v")) |
> + (device_property_read_bool(dev, "mmc-hs200-1_8v")) |
> + (device_property_read_bool(dev, "mmc-hs400-1_8v")))
> + priv->flags |= FLAG_IO_FIXED_1V8;
> + else
> + priv->flags &= ~FLAG_IO_FIXED_1V8;
> +
> + /*
> + * start_signal_voltage_switch() will try 3.3V first
> + * then 1.8V. Use SDHCI_SIGNALING_180 ranther than
> + * SDHCI_SIGNALING_330 to avoid setting voltage to 3.3V
> + * in sdhci_start_signal_voltage_switch().
> + */
> + if (priv->flags & FLAG_IO_FIXED_1V8) {
> + host->flags &= ~SDHCI_SIGNALING_330;
> + host->flags |= SDHCI_SIGNALING_180;
> + }
> +
> + sdhci_enable_v4_mode(host);
> + }
> +
> #ifdef CONFIG_ACPI
> if (pltfm_data == &sdhci_dwcmshc_bf3_pdata)
> sdhci_enable_v4_mode(host);
>
> --
> 2.34.1
>
More information about the linux-riscv
mailing list