[PATCH v7 2/4] crypto: starfive - Add crypto engine support
Jia Jie Ho
jiajie.ho at starfivetech.com
Thu May 4 00:33:58 PDT 2023
Adding device probe and DMA init for StarFive cryptographic module.
Co-developed-by: Huan Feng <huan.feng at starfivetech.com>
Signed-off-by: Huan Feng <huan.feng at starfivetech.com>
Signed-off-by: Jia Jie Ho <jiajie.ho at starfivetech.com>
---
MAINTAINERS | 7 +
drivers/crypto/Kconfig | 1 +
drivers/crypto/Makefile | 1 +
drivers/crypto/starfive/Kconfig | 17 +++
drivers/crypto/starfive/Makefile | 4 +
drivers/crypto/starfive/jh7110-cryp.c | 201 ++++++++++++++++++++++++++
drivers/crypto/starfive/jh7110-cryp.h | 63 ++++++++
7 files changed, 294 insertions(+)
create mode 100644 drivers/crypto/starfive/Kconfig
create mode 100644 drivers/crypto/starfive/Makefile
create mode 100644 drivers/crypto/starfive/jh7110-cryp.c
create mode 100644 drivers/crypto/starfive/jh7110-cryp.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 5f9c544bc189..498f3b7792a6 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -19920,6 +19920,13 @@ F: Documentation/devicetree/bindings/clock/starfive,jh71*.yaml
F: drivers/clk/starfive/clk-starfive-jh71*
F: include/dt-bindings/clock/starfive?jh71*.h
+STARFIVE CRYPTO DRIVER
+M: Jia Jie Ho <jiajie.ho at starfivetech.com>
+M: William Qiu <william.qiu at starfivetech.com>
+S: Supported
+F: Documentation/devicetree/bindings/crypto/starfive*
+F: drivers/crypto/starfive/
+
STARFIVE JH71X0 PINCTRL DRIVERS
M: Emil Renner Berthing <kernel at esmil.dk>
M: Jianlong Huang <jianlong.huang at starfivetech.com>
diff --git a/drivers/crypto/Kconfig b/drivers/crypto/Kconfig
index 3b2516d1433f..c9b6a8747fa1 100644
--- a/drivers/crypto/Kconfig
+++ b/drivers/crypto/Kconfig
@@ -822,5 +822,6 @@ config CRYPTO_DEV_SA2UL
source "drivers/crypto/keembay/Kconfig"
source "drivers/crypto/aspeed/Kconfig"
+source "drivers/crypto/starfive/Kconfig"
endif # CRYPTO_HW
diff --git a/drivers/crypto/Makefile b/drivers/crypto/Makefile
index 476f1a25ca32..5ff5242a1824 100644
--- a/drivers/crypto/Makefile
+++ b/drivers/crypto/Makefile
@@ -52,3 +52,4 @@ obj-y += xilinx/
obj-y += hisilicon/
obj-$(CONFIG_CRYPTO_DEV_AMLOGIC_GXL) += amlogic/
obj-y += keembay/
+obj-y += starfive/
diff --git a/drivers/crypto/starfive/Kconfig b/drivers/crypto/starfive/Kconfig
new file mode 100644
index 000000000000..2436e93d27ef
--- /dev/null
+++ b/drivers/crypto/starfive/Kconfig
@@ -0,0 +1,17 @@
+#
+# StarFive crypto drivers configuration
+#
+
+config CRYPTO_DEV_JH7110
+ tristate "StarFive JH7110 cryptographic engine driver"
+ depends on SOC_STARFIVE
+ select CRYPTO_ENGINE
+ select ARM_AMBA
+ select DMADEVICES
+ select AMBA_PL08X
+ help
+ Support for StarFive JH7110 crypto hardware acceleration engine.
+ This module provides acceleration for public key algo,
+ skciphers, AEAD and hash functions.
+
+ If you choose 'M' here, this module will be called jh7110-crypto.
diff --git a/drivers/crypto/starfive/Makefile b/drivers/crypto/starfive/Makefile
new file mode 100644
index 000000000000..41221acaee39
--- /dev/null
+++ b/drivers/crypto/starfive/Makefile
@@ -0,0 +1,4 @@
+# SPDX-License-Identifier: GPL-2.0
+
+obj-$(CONFIG_CRYPTO_DEV_JH7110) += jh7110-crypto.o
+jh7110-crypto-objs := jh7110-cryp.o
diff --git a/drivers/crypto/starfive/jh7110-cryp.c b/drivers/crypto/starfive/jh7110-cryp.c
new file mode 100644
index 000000000000..4b2505c23168
--- /dev/null
+++ b/drivers/crypto/starfive/jh7110-cryp.c
@@ -0,0 +1,201 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Cryptographic API.
+ *
+ * Support for StarFive hardware cryptographic engine.
+ * Copyright (c) 2022 StarFive Technology
+ *
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/reset.h>
+
+#include "jh7110-cryp.h"
+
+#define DRIVER_NAME "jh7110-crypto"
+
+struct starfive_dev_list {
+ struct list_head dev_list;
+ spinlock_t lock; /* protect dev_list */
+};
+
+static struct starfive_dev_list dev_list = {
+ .dev_list = LIST_HEAD_INIT(dev_list.dev_list),
+ .lock = __SPIN_LOCK_UNLOCKED(dev_list.lock),
+};
+
+struct starfive_cryp_dev *starfive_cryp_find_dev(struct starfive_cryp_ctx *ctx)
+{
+ struct starfive_cryp_dev *cryp = NULL, *tmp;
+
+ spin_lock_bh(&dev_list.lock);
+ if (!ctx->cryp) {
+ list_for_each_entry(tmp, &dev_list.dev_list, list) {
+ cryp = tmp;
+ break;
+ }
+ ctx->cryp = cryp;
+ } else {
+ cryp = ctx->cryp;
+ }
+
+ spin_unlock_bh(&dev_list.lock);
+
+ return cryp;
+}
+
+static int starfive_dma_init(struct starfive_cryp_dev *cryp)
+{
+ dma_cap_mask_t mask;
+
+ dma_cap_zero(mask);
+ dma_cap_set(DMA_SLAVE, mask);
+
+ cryp->tx = dma_request_chan(cryp->dev, "tx");
+ if (IS_ERR(cryp->tx))
+ return dev_err_probe(cryp->dev, PTR_ERR(cryp->tx),
+ "Error requesting tx dma channel.\n");
+
+ cryp->rx = dma_request_chan(cryp->dev, "rx");
+ if (IS_ERR(cryp->rx)) {
+ dma_release_channel(cryp->tx);
+ return dev_err_probe(cryp->dev, PTR_ERR(cryp->rx),
+ "Error requesting rx dma channel.\n");
+ }
+
+ return 0;
+}
+
+static void starfive_dma_cleanup(struct starfive_cryp_dev *cryp)
+{
+ dma_release_channel(cryp->tx);
+ dma_release_channel(cryp->rx);
+}
+
+static int starfive_cryp_probe(struct platform_device *pdev)
+{
+ struct starfive_cryp_dev *cryp;
+ struct resource *res;
+ int ret;
+
+ cryp = devm_kzalloc(&pdev->dev, sizeof(*cryp), GFP_KERNEL);
+ if (!cryp)
+ return -ENOMEM;
+
+ platform_set_drvdata(pdev, cryp);
+ cryp->dev = &pdev->dev;
+
+ cryp->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
+ if (IS_ERR(cryp->base))
+ return dev_err_probe(&pdev->dev, PTR_ERR(cryp->base),
+ "Error remapping memory for platform device\n");
+
+ cryp->phys_base = res->start;
+ cryp->dma_maxburst = 32;
+
+ cryp->hclk = devm_clk_get(&pdev->dev, "hclk");
+ if (IS_ERR(cryp->hclk))
+ return dev_err_probe(&pdev->dev, PTR_ERR(cryp->hclk),
+ "Error getting hardware reference clock\n");
+
+ cryp->ahb = devm_clk_get(&pdev->dev, "ahb");
+ if (IS_ERR(cryp->ahb))
+ return dev_err_probe(&pdev->dev, PTR_ERR(cryp->ahb),
+ "Error getting ahb reference clock\n");
+
+ cryp->rst = devm_reset_control_get_shared(cryp->dev, NULL);
+ if (IS_ERR(cryp->rst))
+ return dev_err_probe(&pdev->dev, PTR_ERR(cryp->rst),
+ "Error getting hardware reset line\n");
+
+ clk_prepare_enable(cryp->hclk);
+ clk_prepare_enable(cryp->ahb);
+ reset_control_deassert(cryp->rst);
+
+ spin_lock(&dev_list.lock);
+ list_add(&cryp->list, &dev_list.dev_list);
+ spin_unlock(&dev_list.lock);
+
+ ret = starfive_dma_init(cryp);
+ if (ret) {
+ if (ret == -EPROBE_DEFER)
+ goto err_probe_defer;
+ else
+ goto err_dma_init;
+ }
+
+ /* Initialize crypto engine */
+ cryp->engine = crypto_engine_alloc_init(&pdev->dev, 1);
+ if (!cryp->engine) {
+ ret = -ENOMEM;
+ goto err_engine;
+ }
+
+ ret = crypto_engine_start(cryp->engine);
+ if (ret)
+ goto err_engine_start;
+
+ return 0;
+
+err_engine_start:
+ crypto_engine_exit(cryp->engine);
+err_engine:
+ starfive_dma_cleanup(cryp);
+err_dma_init:
+ spin_lock(&dev_list.lock);
+ list_del(&cryp->list);
+ spin_unlock(&dev_list.lock);
+
+ clk_disable_unprepare(cryp->hclk);
+ clk_disable_unprepare(cryp->ahb);
+ reset_control_assert(cryp->rst);
+err_probe_defer:
+ return ret;
+}
+
+static int starfive_cryp_remove(struct platform_device *pdev)
+{
+ struct starfive_cryp_dev *cryp = platform_get_drvdata(pdev);
+
+ crypto_engine_stop(cryp->engine);
+ crypto_engine_exit(cryp->engine);
+
+ starfive_dma_cleanup(cryp);
+
+ spin_lock(&dev_list.lock);
+ list_del(&cryp->list);
+ spin_unlock(&dev_list.lock);
+
+ clk_disable_unprepare(cryp->hclk);
+ clk_disable_unprepare(cryp->ahb);
+ reset_control_assert(cryp->rst);
+
+ return 0;
+}
+
+static const struct of_device_id starfive_dt_ids[] __maybe_unused = {
+ { .compatible = "starfive,jh7110-crypto", .data = NULL},
+ {},
+};
+MODULE_DEVICE_TABLE(of, starfive_dt_ids);
+
+static struct platform_driver starfive_cryp_driver = {
+ .probe = starfive_cryp_probe,
+ .remove = starfive_cryp_remove,
+ .driver = {
+ .name = DRIVER_NAME,
+ .of_match_table = starfive_dt_ids,
+ },
+};
+
+module_platform_driver(starfive_cryp_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("StarFive JH7110 Cryptographic Module");
diff --git a/drivers/crypto/starfive/jh7110-cryp.h b/drivers/crypto/starfive/jh7110-cryp.h
new file mode 100644
index 000000000000..393efd38b098
--- /dev/null
+++ b/drivers/crypto/starfive/jh7110-cryp.h
@@ -0,0 +1,63 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __STARFIVE_STR_H__
+#define __STARFIVE_STR_H__
+
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+
+#include <crypto/engine.h>
+
+#define STARFIVE_ALG_CR_OFFSET 0x0
+#define STARFIVE_ALG_FIFO_OFFSET 0x4
+#define STARFIVE_IE_MASK_OFFSET 0x8
+#define STARFIVE_IE_FLAG_OFFSET 0xc
+#define STARFIVE_DMA_IN_LEN_OFFSET 0x10
+#define STARFIVE_DMA_OUT_LEN_OFFSET 0x14
+
+#define STARFIVE_MSG_BUFFER_SIZE SZ_16K
+
+union starfive_alg_cr {
+ u32 v;
+ struct {
+ u32 start :1;
+ u32 aes_dma_en :1;
+ u32 rsvd_0 :1;
+ u32 hash_dma_en :1;
+ u32 alg_done :1;
+ u32 rsvd_1 :3;
+ u32 clear :1;
+ u32 rsvd_2 :23;
+ };
+};
+
+struct starfive_cryp_ctx {
+ struct crypto_engine_ctx enginectx;
+ struct starfive_cryp_dev *cryp;
+};
+
+struct starfive_cryp_dev {
+ struct list_head list;
+ struct device *dev;
+
+ struct clk *hclk;
+ struct clk *ahb;
+ struct reset_control *rst;
+
+ void __iomem *base;
+ phys_addr_t phys_base;
+
+ u32 dma_maxburst;
+ struct dma_chan *tx;
+ struct dma_chan *rx;
+ struct dma_slave_config cfg_in;
+ struct dma_slave_config cfg_out;
+
+ struct crypto_engine *engine;
+
+ union starfive_alg_cr alg_cr;
+};
+
+struct starfive_cryp_dev *starfive_cryp_find_dev(struct starfive_cryp_ctx *ctx);
+
+#endif
--
2.25.1
More information about the linux-riscv
mailing list