[PATCH v3 5/5] dts: usb: add StarFive JH7110 USB dts configuration.

[Minda Chen]

On 2023/3/16 10:43, Peter Chen wrote:
> On 23-03-15 18:44:11, Minda Chen wrote:
>> USB Glue layer and Cadence USB subnode configuration,
>> also includes USB and PCIe phy dts configuration.
>> 
>> Signed-off-by: Minda Chen <minda.chen at starfivetech.com>
>> ---
>>  .../jh7110-starfive-visionfive-2.dtsi         |  7 +++
>>  arch/riscv/boot/dts/starfive/jh7110.dtsi      | 54 +++++++++++++++++++
>>  2 files changed, 61 insertions(+)
>> 
>> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
>> index a132debb9b53..c64476aebc1a 100644
>> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
>> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
>> @@ -236,3 +236,10 @@
>>  	pinctrl-0 = <&uart0_pins>;
>>  	status = "okay";
>>  };
>> +
>> +&usb0 {
>> +	status = "okay";
>> +	usbdrd_cdns3: usb at 0 {
>> +		dr_mode = "peripheral";
>> +	};
>> +};
>> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
>> index f70a4ed47eb4..17722fd1be62 100644
>> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
>> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
>> @@ -362,6 +362,60 @@
>>  			status = "disabled";
>>  		};
>>  
>> +		usb0: usb at 10100000 {
>> +			compatible = "starfive,jh7110-usb";
>> +			clocks = <&stgcrg JH7110_STGCLK_USB0_LPM>,
>> +				 <&stgcrg JH7110_STGCLK_USB0_STB>,
>> +				 <&stgcrg JH7110_STGCLK_USB0_APB>,
>> +				 <&stgcrg JH7110_STGCLK_USB0_AXI>,
>> +				 <&stgcrg JH7110_STGCLK_USB0_UTMI_APB>;
>> +			clock-names = "lpm", "stb", "apb", "axi", "utmi_apb";
>> +			resets = <&stgcrg JH7110_STGRST_USB0_PWRUP>,
>> +				 <&stgcrg JH7110_STGRST_USB0_APB>,
>> +				 <&stgcrg JH7110_STGRST_USB0_AXI>,
>> +				 <&stgcrg JH7110_STGRST_USB0_UTMI_APB>;
>> +			starfive,stg-syscon = <&stg_syscon 0x4 0xc4 0x148 0x1f4>;
>> +			starfive,sys-syscon = <&sys_syscon 0x18>;
>> +			status = "disabled";
>> +			#address-cells = <1>;
>> +			#size-cells = <1>;
>> +			ranges = <0x0 0x0 0x10100000 0x100000>;
> 
> Why it is four entry at ranges? Your address-cells and size-cells are
> both 1, and your binding-doc is also three?
> 
> Peter
Because the parent soc node address-cells is 2. So the local address is 2 entry.
  	
	soc {
                compatible = "simple-bus";
                interrupt-parent = <&plic>;
                #address-cells = <2>;
                #size-cells = <2>;
                ranges;
                ...

So should I change the binding-doc ?
>> +
>> +			usbdrd_cdns3: usb at 0 {
>> +				compatible = "cdns,usb3";
>> +				reg = <0x0 0x10000>,
>> +				      <0x10000 0x10000>,
>> +				      <0x20000 0x10000>;
>> +				reg-names = "otg", "xhci", "dev";
>> +				interrupts = <100>, <108>, <110>;
>> +				interrupt-names = "host", "peripheral", "otg";
>> +				phys = <&usbphy0>;
>> +				phy-names = "cdns3,usb2-phy";
>> +				maximum-speed = "super-speed";
>> +			};
>> +		};
>> +
>> +		usbphy0: phy at 10200000 {
>> +			compatible = "starfive,jh7110-usb-phy";
>> +			reg = <0x0 0x10200000 0x0 0x10000>;
>> +			clocks = <&syscrg JH7110_SYSCLK_USB_125M>,
>> +				 <&stgcrg JH7110_STGCLK_USB0_APP_125>;
>> +			clock-names = "125m", "app_125";
>> +			#phy-cells = <0>;
>> +		};
>> +
>> +		pciephy0: phy at 10210000 {
>> +			compatible = "starfive,jh7110-pcie-phy";
>> +			reg = <0x0 0x10210000 0x0 0x10000>;
>> +			#phy-cells = <0>;
>> +		};
>> +
>> +		pciephy1: phy at 10220000 {
>> +			compatible = "starfive,jh7110-pcie-phy";
>> +			reg = <0x0 0x10220000 0x0 0x10000>;
>> +			#phy-cells = <0>;
>> +		};
>> +
>>  		stgcrg: clock-controller at 10230000 {
>>  			compatible = "starfive,jh7110-stgcrg";
>>  			reg = <0x0 0x10230000 0x0 0x10000>;
>> -- 
>> 2.17.1
>> 
>