[PATCH v5 05/12] riscv: dts: starfive: jh7110: Add ethernet device nodes

[Emil Renner Berthing]

On Fri, 3 Mar 2023 at 10:01, Samin Guo <samin.guo at starfivetech.com> wrote:
>
> Add JH7110 ethernet device node to support gmac driver for the JH7110
> RISC-V SoC.
>
> Signed-off-by: Yanhong Wang <yanhong.wang at starfivetech.com>
> Signed-off-by: Samin Guo <samin.guo at starfivetech.com>
> ---
>  arch/riscv/boot/dts/starfive/jh7110.dtsi | 91 ++++++++++++++++++++++++
>  1 file changed, 91 insertions(+)
>
> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> index 09806418ed1b..2ce28292b721 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> @@ -233,6 +233,13 @@
>                 #clock-cells = <0>;
>         };
>
> +       stmmac_axi_setup: stmmac-axi-config {
> +               snps,lpi_en;
> +               snps,wr_osr_lmt = <4>;
> +               snps,rd_osr_lmt = <4>;
> +               snps,blen = <256 128 64 32 0 0 0>;
> +       };
> +
>         tdm_ext: tdm-ext-clock {
>                 compatible = "fixed-clock";
>                 clock-output-names = "tdm_ext";
> @@ -518,5 +525,89 @@
>                         gpio-controller;
>                         #gpio-cells = <2>;
>                 };
> +
> +               gmac0: ethernet at 16030000 {
> +                       compatible = "starfive,jh7110-dwmac", "snps,dwmac-5.20";
> +                       reg = <0x0 0x16030000 0x0 0x10000>;
> +                       clocks = <&aoncrg JH7110_AONCLK_GMAC0_AXI>,
> +                                <&aoncrg JH7110_AONCLK_GMAC0_AHB>,
> +                                <&syscrg JH7110_SYSCLK_GMAC0_PTP>,
> +                                <&aoncrg JH7110_AONCLK_GMAC0_TX_INV>,
> +                                <&syscrg JH7110_SYSCLK_GMAC0_GTXC>;
> +                       clock-names = "stmmaceth", "pclk", "ptp_ref",
> +                                     "tx", "gtx";
> +                       resets = <&aoncrg JH7110_AONRST_GMAC0_AXI>,
> +                                <&aoncrg JH7110_AONRST_GMAC0_AHB>;
> +                       reset-names = "stmmaceth", "ahb";
> +                       interrupts = <7>, <6>, <5>;
> +                       interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
> +                       phy-mode = "rgmii-id";
> +                       snps,multicast-filter-bins = <64>;
> +                       snps,perfect-filter-entries = <8>;
> +                       rx-fifo-depth = <2048>;
> +                       tx-fifo-depth = <2048>;
> +                       snps,fixed-burst;
> +                       snps,no-pbl-x8;
> +                       snps,force_thresh_dma_mode;
> +                       snps,axi-config = <&stmmac_axi_setup>;
> +                       snps,tso;
> +                       snps,en-tx-lpi-clockgating;
> +                       snps,txpbl = <16>;
> +                       snps,rxpbl = <16>;
> +                       status = "disabled";
> +                       phy-handle = <&phy0>;
> +
> +                       mdio {
> +                               #address-cells = <1>;
> +                               #size-cells = <0>;
> +                               compatible = "snps,dwmac-mdio";
> +
> +                               phy0: ethernet-phy at 0 {
> +                                       reg = <0>;
> +                               };
> +                       };
> +               };
> +
> +               gmac1: ethernet at 16040000 {
> +                       compatible = "starfive,jh7110-dwmac", "snps,dwmac-5.20";
> +                       reg = <0x0 0x16040000 0x0 0x10000>;
> +                       clocks = <&syscrg JH7110_SYSCLK_GMAC1_AXI>,
> +                                <&syscrg JH7110_SYSCLK_GMAC1_AHB>,
> +                                <&syscrg JH7110_SYSCLK_GMAC1_PTP>,
> +                                <&syscrg JH7110_SYSCLK_GMAC1_TX_INV>,
> +                                <&syscrg JH7110_SYSCLK_GMAC1_GTXC>;
> +                       clock-names = "stmmaceth", "pclk", "ptp_ref",
> +                                     "tx", "gtx";
> +                       resets = <&syscrg JH7110_SYSRST_GMAC1_AXI>,
> +                                <&syscrg JH7110_SYSRST_GMAC1_AHB>;
> +                       reset-names = "stmmaceth", "ahb";
> +                       interrupts = <78>, <77>, <76>;
> +                       interrupt-names = "macirq", "eth_wake_irq", "eth_lpi";
> +                       phy-mode = "rgmii-id";
> +                       snps,multicast-filter-bins = <64>;
> +                       snps,perfect-filter-entries = <8>;
> +                       rx-fifo-depth = <2048>;
> +                       tx-fifo-depth = <2048>;
> +                       snps,fixed-burst;
> +                       snps,no-pbl-x8;
> +                       snps,force_thresh_dma_mode;
> +                       snps,axi-config = <&stmmac_axi_setup>;
> +                       snps,tso;
> +                       snps,en-tx-lpi-clockgating;
> +                       snps,txpbl = <16>;
> +                       snps,rxpbl = <16>;
> +                       status = "disabled";
> +                       phy-handle = <&phy1>;
> +
> +                       mdio {
> +                               #address-cells = <1>;
> +                               #size-cells = <0>;
> +                               compatible = "snps,dwmac-mdio";
> +
> +                               phy1: ethernet-phy at 1 {
> +                                       reg = <0>;

I'm getting errors on eth1 unless this is set to <1>. In any case the
number after @ in the node name should match the reg value.

> +                               };
> +                       };
> +               };
>         };
>  };
> --
> 2.17.1
>
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv