[PATCH v4 2/7] clk: starfive: Add StarFive JH7110 PLL clock driver
Xingyu Wu
xingyu.wu at starfivetech.com
Fri Jun 2 02:39:02 PDT 2023
On 2023/6/1 19:02, Emil Renner Berthing wrote:
> Hi Xingyu,
>
> Thanks for working on this.
>
> On Fri, 12 May 2023 at 04:24, Xingyu Wu <xingyu.wu at starfivetech.com> wrote:
>>
>> Add driver for the StarFive JH7110 PLL clock controller
>> and they work by reading and setting syscon registers.
>>
>> Signed-off-by: Xingyu Wu <xingyu.wu at starfivetech.com>
>> ---
>> MAINTAINERS | 6 +
>> drivers/clk/starfive/Kconfig | 8 +
>> drivers/clk/starfive/Makefile | 1 +
>> .../clk/starfive/clk-starfive-jh7110-pll.c | 309 ++++++++++++++++
>> .../clk/starfive/clk-starfive-jh7110-pll.h | 331 ++++++++++++++++++
>> 5 files changed, 655 insertions(+)
>> create mode 100644 drivers/clk/starfive/clk-starfive-jh7110-pll.c
>> create mode 100644 drivers/clk/starfive/clk-starfive-jh7110-pll.h
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 7e0b87d5aa2e..0fb4a703f66f 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -20087,6 +20087,12 @@ S: Supported
>> F: Documentation/devicetree/bindings/mmc/starfive*
>> F: drivers/mmc/host/dw_mmc-starfive.c
>>
>> +STARFIVE JH7110 PLL CLOCK DRIVER
>> +M: Xingyu Wu <xingyu.wu at starfivetech.com>
>> +S: Supported
>> +F: Documentation/devicetree/bindings/clock/starfive,jh7110-pll.yaml
>> +F: drivers/clk/starfive/clk-starfive-jh7110-pll.*
>> +
>> STARFIVE JH71X0 CLOCK DRIVERS
>> M: Emil Renner Berthing <kernel at esmil.dk>
>> M: Hal Feng <hal.feng at starfivetech.com>
>> diff --git a/drivers/clk/starfive/Kconfig b/drivers/clk/starfive/Kconfig
>> index 5d2333106f13..5195f7be5213 100644
>> --- a/drivers/clk/starfive/Kconfig
>> +++ b/drivers/clk/starfive/Kconfig
>> @@ -21,6 +21,14 @@ config CLK_STARFIVE_JH7100_AUDIO
>> Say Y or M here to support the audio clocks on the StarFive JH7100
>> SoC.
>>
>> +config CLK_STARFIVE_JH7110_PLL
>> + bool "StarFive JH7110 PLL clock support"
>> + depends on ARCH_STARFIVE || COMPILE_TEST
>> + default ARCH_STARFIVE
>> + help
>> + Say yes here to support the PLL clock controller on the
>> + StarFive JH7110 SoC.
>> +
>> config CLK_STARFIVE_JH7110_SYS
>> bool "StarFive JH7110 system clock support"
>> depends on ARCH_STARFIVE || COMPILE_TEST
>> diff --git a/drivers/clk/starfive/Makefile b/drivers/clk/starfive/Makefile
>> index f3df7d957b1e..b48e539e52b0 100644
>> --- a/drivers/clk/starfive/Makefile
>> +++ b/drivers/clk/starfive/Makefile
>> @@ -4,5 +4,6 @@ obj-$(CONFIG_CLK_STARFIVE_JH71X0) += clk-starfive-jh71x0.o
>> obj-$(CONFIG_CLK_STARFIVE_JH7100) += clk-starfive-jh7100.o
>> obj-$(CONFIG_CLK_STARFIVE_JH7100_AUDIO) += clk-starfive-jh7100-audio.o
>>
>> +obj-$(CONFIG_CLK_STARFIVE_JH7110_PLL) += clk-starfive-jh7110-pll.o
>> obj-$(CONFIG_CLK_STARFIVE_JH7110_SYS) += clk-starfive-jh7110-sys.o
>> obj-$(CONFIG_CLK_STARFIVE_JH7110_AON) += clk-starfive-jh7110-aon.o
>> diff --git a/drivers/clk/starfive/clk-starfive-jh7110-pll.c b/drivers/clk/starfive/clk-starfive-jh7110-pll.c
>> new file mode 100644
>> index 000000000000..f86deddd4bef
>> --- /dev/null
>> +++ b/drivers/clk/starfive/clk-starfive-jh7110-pll.c
>> @@ -0,0 +1,309 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * StarFive JH7110 PLL Clock Generator Driver
>> + *
>> + * Copyright (C) 2023 StarFive Technology Co., Ltd.
>> + *
>> + * This driver is about to register JH7110 PLL clock generator and support ops.
>> + * The JH7110 have three PLL clock, PLL0, PLL1 and PLL2.
>> + * Each PLL clocks work in integer mode or fraction mode by some dividers,
>> + * and the configuration registers and dividers are set in several syscon registers.
>> + * The formula for calculating frequency is:
>> + * Fvco = Fref * (NI + NF) / M / Q1
>> + * Fref: OSC source clock rate
>> + * NI: integer frequency dividing ratio of feedback divider, set by fbdiv[11:0].
>> + * NF: fractional frequency dividing ratio, set by frac[23:0]. NF = frac[23:0] / 2^24 = 0 ~ 0.999.
>> + * M: frequency dividing ratio of pre-divider, set by prediv[5:0].
>> + * Q1: frequency dividing ratio of post divider, set by postdiv1[1:0], Q1= 1,2,4,8.
>> + */
>> +
>> +#include <linux/clk-provider.h>
>> +#include <linux/debugfs.h>
>> +#include <linux/device.h>
>> +#include <linux/kernel.h>
>> +#include <linux/mfd/syscon.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/regmap.h>
>> +
>> +#include <dt-bindings/clock/starfive,jh7110-crg.h>
>> +
>> +#include "clk-starfive-jh7110-pll.h"
>> +
>> +struct jh7110_pll_conf_variant {
>> + unsigned int pll_nums;
>> + struct jh7110_pll_syscon_conf conf[];
>> +};
>> +
>> +static const struct jh7110_pll_conf_variant jh7110_pll_variant = {
>> + .pll_nums = JH7110_PLLCLK_END,
>> + .conf = {
>> + JH7110_PLL(JH7110_CLK_PLL0_OUT, "pll0_out",
>> + JH7110_PLL0_FREQ_MAX, jh7110_pll0_syscon_val_preset),
>> + JH7110_PLL(JH7110_CLK_PLL1_OUT, "pll1_out",
>> + JH7110_PLL1_FREQ_MAX, jh7110_pll1_syscon_val_preset),
>> + JH7110_PLL(JH7110_CLK_PLL2_OUT, "pll2_out",
>> + JH7110_PLL2_FREQ_MAX, jh7110_pll2_syscon_val_preset),
>> + },
>> +};
>> +
>> +static struct jh7110_clk_pll_data *jh7110_pll_data_from(struct clk_hw *hw)
>> +{
>> + return container_of(hw, struct jh7110_clk_pll_data, hw);
>> +}
>> +
>> +static struct jh7110_clk_pll_priv *jh7110_pll_priv_from(struct jh7110_clk_pll_data *data)
>> +{
>> + return container_of(data, struct jh7110_clk_pll_priv, data[data->idx]);
>> +}
>> +
>> +/* Read register value from syscon and calculate PLL(x) frequency */
>> +static unsigned long jh7110_pll_get_freq(struct jh7110_clk_pll_data *data,
>> + unsigned long parent_rate)
>> +{
>> + struct jh7110_clk_pll_priv *priv = jh7110_pll_priv_from(data);
>> + struct jh7110_pll_syscon_offset *offset = &data->conf.offsets;
>> + struct jh7110_pll_syscon_mask *mask = &data->conf.masks;
>> + struct jh7110_pll_syscon_shift *shift = &data->conf.shifts;
>> + unsigned long frac_cal;
>> + u32 dacpd;
>> + u32 dsmpd;
>> + u32 fbdiv;
>> + u32 prediv;
>> + u32 postdiv1;
>> + u32 frac;
>> + u32 reg_val;
>> +
>> + regmap_read(priv->syscon_regmap, offset->dacpd, ®_val);
>> + dacpd = (reg_val & mask->dacpd) >> shift->dacpd;
>> +
>> + regmap_read(priv->syscon_regmap, offset->dsmpd, ®_val);
>> + dsmpd = (reg_val & mask->dsmpd) >> shift->dsmpd;
>> +
>> + regmap_read(priv->syscon_regmap, offset->fbdiv, ®_val);
>> + fbdiv = (reg_val & mask->fbdiv) >> shift->fbdiv;
>> +
>> + regmap_read(priv->syscon_regmap, offset->prediv, ®_val);
>> + prediv = (reg_val & mask->prediv) >> shift->prediv;
>> +
>> + regmap_read(priv->syscon_regmap, offset->postdiv1, ®_val);
>> + /* postdiv1 = 2 ^ reg_val */
>> + postdiv1 = 1 << ((reg_val & mask->postdiv1) >> shift->postdiv1);
>> +
>> + regmap_read(priv->syscon_regmap, offset->frac, ®_val);
>> + frac = (reg_val & mask->frac) >> shift->frac;
>> +
>> + /*
>> + * Integer Mode (Both 1) or Fraction Mode (Both 0).
>> + * And the decimal places are counted by expanding them by
>> + * a factor of STARFIVE_PLL_FRAC_PATR_SIZE.
>> + */
>> + if (dacpd == 1 && dsmpd == 1)
>> + frac_cal = 0;
>> + else if (dacpd == 0 && dsmpd == 0)
>> + frac_cal = (unsigned long)frac * STARFIVE_PLL_FRAC_PATR_SIZE / (1 << 24);
>> + else
>> + return 0;
>> +
>> + /* Fvco = Fref * (NI + NF) / M / Q1 */
>> + return (parent_rate / STARFIVE_PLL_FRAC_PATR_SIZE *
>> + (fbdiv * STARFIVE_PLL_FRAC_PATR_SIZE + frac_cal) / prediv / postdiv1);
>
> You have
>
> rate = parent * (fbdiv + frac/2^24) / prediv / 2^postdiv1regval
>
> Where postdiv1regval is the raw postdiv1 register value. This can also
> be written
>
> rate = (parent * fbdiv + parent * frac / 2^24) / (prediv * 2^postdiv1regval)
>
> so how about
>
> if (dacpd == 1 && dsmpd == 1)
> rate = 0;
> else if (dacpd == 0 && dsmpd == 0)
> rate = parent * frac / (1UL << 24);
> else
> return 0;
>
> rate += parent * fbdiv;
> rate /= prediv << postdiv1regval;
> return rate;
>
Thanks for you suggestions. I will modify this.
And I have a question, should I keep the 'STARFIVE_PLL_FRAC_PATR_SIZE ' as integer to calculate the fractional part of 'frac'?
>> +}
>> +
>> +static unsigned long jh7110_pll_rate_sub_fabs(unsigned long rate1, unsigned long rate2)
>> +{
>> + return rate1 > rate2 ? (rate1 - rate2) : (rate2 - rate1);
>> +}
>> +
>> +/* Select the appropriate frequency from the already configured registers value */
>> +static void jh7110_pll_select_near_freq_id(struct jh7110_clk_pll_data *data,
>> + unsigned long rate)
>> +{
>> + const struct jh7110_pll_syscon_val *val;
>> + unsigned int id;
>> + unsigned long rate_diff;
>> +
>> + /* compare the frequency one by one from small to large in order */
>> + for (id = 0; id < data->conf.preset_val_nums; id++) {
>> + val = &data->conf.preset_val[id];
>> +
>> + if (rate == val->freq)
>> + goto match_end;
>> +
>> + /* select near frequency */
>
> Is there any reason we can't just pick the highest rate <= the
> requested rate, just like we do for the regular clock dividers?
It sounds like rounding down. This is a good idea and I will fix it.
>
>> + if (rate < val->freq) {
>> + /* The last frequency is closer to the target rate than this time. */
>> + if (id > 0)
>> + if (rate_diff < jh7110_pll_rate_sub_fabs(rate, val->freq))
>> + id--;
>> +
>> + goto match_end;
>> + } else {
>> + rate_diff = jh7110_pll_rate_sub_fabs(rate, val->freq);
>> + }
>> + }
>> +
>> +match_end:
>> + data->freq_select_idx = id;
>> +}
>> +
>> +static int jh7110_pll_set_freq_syscon(struct jh7110_clk_pll_data *data)
>> +{
>> + struct jh7110_clk_pll_priv *priv = jh7110_pll_priv_from(data);
>> + struct jh7110_pll_syscon_offset *offset = &data->conf.offsets;
>> + struct jh7110_pll_syscon_mask *mask = &data->conf.masks;
>> + struct jh7110_pll_syscon_shift *shift = &data->conf.shifts;
>> + const struct jh7110_pll_syscon_val *val = &data->conf.preset_val[data->freq_select_idx];
>> +
>> + /* frac: Integer Mode (Both 1) or Fraction Mode (Both 0) */
>> + if (val->dacpd == 0 && val->dsmpd == 0)
>> + regmap_update_bits(priv->syscon_regmap, offset->frac, mask->frac,
>> + (val->frac << shift->frac));
>> + else if (val->dacpd != val->dsmpd)
>> + return -EINVAL;
>> +
>> + /* fbdiv value should be 8 to 4095 */
>> + if (val->fbdiv < 8)
>> + return -EINVAL;
>> +
>> + regmap_update_bits(priv->syscon_regmap, offset->dacpd, mask->dacpd,
>> + (val->dacpd << shift->dacpd));
>> + regmap_update_bits(priv->syscon_regmap, offset->dsmpd, mask->dsmpd,
>> + (val->dsmpd << shift->dsmpd));
>> + regmap_update_bits(priv->syscon_regmap, offset->prediv, mask->prediv,
>> + (val->prediv << shift->prediv));
>> + regmap_update_bits(priv->syscon_regmap, offset->fbdiv, mask->fbdiv,
>> + (val->fbdiv << shift->fbdiv));
>> + regmap_update_bits(priv->syscon_regmap, offset->postdiv1, mask->postdiv1,
>> + ((val->postdiv1 >> 1) << shift->postdiv1));
>
> It seems like you're storing the divider and not the register value in
> the presets. Since the divider is 2^regval it means you need to write
> log2 (divider) into the register, but here you store divider >> 1 aka
> divider / 2.
Oh, It's my mistake. The values of post divider are 1,2,4, and 8, which pass when it equals 1, 2, and 4, but is failed when it equals 8.
>
> I'd strongly suggest you just store the register value, and just use
> 2^regval when you need the divider. This way you won't need to ever
> calculate log2 of anything.
Great. Using the register value directly avoid some calculations.
>
>> +
>> + return 0;
>> +}
>> +
>> +static unsigned long jh7110_pll_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
>> +{
>> + struct jh7110_clk_pll_data *data = jh7110_pll_data_from(hw);
>> +
>> + return jh7110_pll_get_freq(data, parent_rate);
>> +}
>> +
>> +static int jh7110_pll_determine_rate(struct clk_hw *hw, struct clk_rate_request *req)
>> +{
>> + struct jh7110_clk_pll_data *data = jh7110_pll_data_from(hw);
>
> What happens if the parent rate != 24MHz? Then all your presets will
> be wrong. We probably want to guard against that.
Will fix and add a check for parent rate.
>
>> + jh7110_pll_select_near_freq_id(data, req->rate);
>> + req->rate = data->conf.preset_val[data->freq_select_idx].freq;
>> +
>> + return 0;
>> +}
>> +
>> +static int jh7110_pll_set_rate(struct clk_hw *hw, unsigned long rate,
>> + unsigned long parent_rate)
>> +{
>> + struct jh7110_clk_pll_data *data = jh7110_pll_data_from(hw);
>> +
>> + return jh7110_pll_set_freq_syscon(data);
>> +}
>> +
>> +#ifdef CONFIG_DEBUG_FS
>> +static void jh7110_pll_debug_init(struct clk_hw *hw, struct dentry *dentry)
>> +{
>> + static const struct debugfs_reg32 jh7110_clk_pll_reg = {
>> + .name = "CTRL",
>> + .offset = 0,
>> + };
>> + struct jh7110_clk_pll_data *data = jh7110_pll_data_from(hw);
>> + struct jh7110_clk_pll_priv *priv = jh7110_pll_priv_from(data);
>> + struct debugfs_regset32 *regset;
>> +
>> + regset = devm_kzalloc(priv->dev, sizeof(*regset), GFP_KERNEL);
>> + if (!regset)
>> + return;
>> +
>> + regset->regs = &jh7110_clk_pll_reg;
>> + regset->nregs = 1;
>
> You never set regset->base, so this function creates a registers file
> that just shows the contents of address 0. I don't think you tested
> this.
Will add the regset->base.
>
>> +
>> + debugfs_create_regset32("registers", 0400, dentry, regset);
>> +}
>> +#else
>> +#define jh7110_pll_debug_init NULL
>> +#endif
>> +
>> +static const struct clk_ops jh7110_pll_ops = {
>> + .recalc_rate = jh7110_pll_recalc_rate,
>> + .determine_rate = jh7110_pll_determine_rate,
>> + .set_rate = jh7110_pll_set_rate,
>> + .debug_init = jh7110_pll_debug_init,
>> +};
>> +
>> +static struct clk_hw *jh7110_pll_get(struct of_phandle_args *clkspec, void *data)
>> +{
>> + struct jh7110_clk_pll_priv *priv = data;
>> + unsigned int idx = clkspec->args[0];
>> +
>> + if (idx < priv->pll_nums)
>> + return &priv->data[idx].hw;
>> +
>> + return ERR_PTR(-EINVAL);
>> +}
>> +
>> +static int jh7110_pll_probe(struct platform_device *pdev)
>> +{
>> + const struct jh7110_pll_conf_variant *variant;
>> + struct jh7110_clk_pll_priv *priv;
>> + struct jh7110_clk_pll_data *data;
>> + int ret;
>> + unsigned int idx;
>> +
>> + variant = of_device_get_match_data(&pdev->dev);
>> + if (!variant)
>> + return -ENOMEM;
>> +
>> + priv = devm_kzalloc(&pdev->dev, struct_size(priv, data, variant->pll_nums),
>> + GFP_KERNEL);
>> + if (!priv)
>> + return -ENOMEM;
>> +
>> + priv->dev = &pdev->dev;
>> + priv->syscon_regmap = syscon_node_to_regmap(priv->dev->of_node->parent);
>> + if (IS_ERR(priv->syscon_regmap))
>> + return PTR_ERR(priv->syscon_regmap);
>> +
>> + priv->pll_nums = variant->pll_nums;
>> + for (idx = 0; idx < priv->pll_nums; idx++) {
>> + struct clk_parent_data parents = {
>> + .index = 0,
>> + };
>> + struct clk_init_data init = {
>> + .name = variant->conf[idx].name,
>> + .ops = &jh7110_pll_ops,
>> + .parent_data = &parents,
>> + .num_parents = 1,
>> + .flags = 0,
>> + };
>> +
>> + data = &priv->data[idx];
>> + data->conf = variant->conf[idx];
>
> Why do you need to copy all this static data? Can't you just reference
> the static const version you already have?
Will use the address variable to reference it.
>
>> + data->hw.init = &init;
>> + data->idx = idx;
>> +
>> + ret = devm_clk_hw_register(&pdev->dev, &data->hw);
>> + if (ret)
>> + return ret;
>> + }
>> +
>> + return devm_of_clk_add_hw_provider(&pdev->dev, jh7110_pll_get, priv);
>> +}
>> +
>> +static const struct of_device_id jh7110_pll_match[] = {
>> + { .compatible = "starfive,jh7110-pll", .data = &jh7110_pll_variant },
>> + { /* sentinel */ }
>> +};
>> +MODULE_DEVICE_TABLE(of, jh7110_pll_match);
>> +
>> +static struct platform_driver jh7110_pll_driver = {
>> + .driver = {
>> + .name = "clk-starfive-jh7110-pll",
>> + .of_match_table = jh7110_pll_match,
>> + },
>> +};
>> +builtin_platform_driver_probe(jh7110_pll_driver, jh7110_pll_probe);
>> diff --git a/drivers/clk/starfive/clk-starfive-jh7110-pll.h b/drivers/clk/starfive/clk-starfive-jh7110-pll.h
>> new file mode 100644
>> index 000000000000..526f21670fe3
>> --- /dev/null
>> +++ b/drivers/clk/starfive/clk-starfive-jh7110-pll.h
>
> This header is never used outside of clk-starfive-jh7110-pll.c. Please
> just merge it into that file.
Will fix.
>
>> @@ -0,0 +1,331 @@
>> +/* SPDX-License-Identifier: GPL-2.0 OR MIT */
>> +/*
>> + * StarFive JH7110 PLL Clock Generator Driver
>> + *
>> + * Copyright (C) 2023 StarFive Technology Co., Ltd.
>> + */
>> +
>> +#ifndef _CLK_STARFIVE_JH7110_PLL_H_
>> +#define _CLK_STARFIVE_JH7110_PLL_H_
>> +
>> +#include <linux/bits.h>
>> +
>> +/* The decimal places are counted by expanding them by a factor of STARFIVE_PLL_FRAC_PATR_SIZE */
>> +#define STARFIVE_PLL_FRAC_PATR_SIZE 1000
>> +
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_DACPD_OFFSET 0x18
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_DACPD_SHIFT 24
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_DACPD_MASK BIT(24)
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_DSMPD_OFFSET 0x18
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_DSMPD_SHIFT 25
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_DSMPD_MASK BIT(25)
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_FBDIV_OFFSET 0x1c
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_FBDIV_SHIFT 0
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_FBDIV_MASK GENMASK(11, 0)
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_FRAC_OFFSET 0x20
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_FRAC_SHIFT 0
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_FRAC_MASK GENMASK(23, 0)
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_POSTDIV1_OFFSET 0x20
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_POSTDIV1_SHIFT 28
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_POSTDIV1_MASK GENMASK(29, 28)
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_PREDIV_OFFSET 0x24
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_PREDIV_SHIFT 0
>> +#define STARFIVE_JH7110_CLK_PLL0_OUT_PREDIV_MASK GENMASK(5, 0)
>> +
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_DACPD_OFFSET 0x24
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_DACPD_SHIFT 15
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_DACPD_MASK BIT(15)
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_DSMPD_OFFSET 0x24
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_DSMPD_SHIFT 16
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_DSMPD_MASK BIT(16)
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_FBDIV_OFFSET 0x24
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_FBDIV_SHIFT 17
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_FBDIV_MASK GENMASK(28, 17)
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_FRAC_OFFSET 0x28
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_FRAC_SHIFT 0
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_FRAC_MASK GENMASK(23, 0)
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_POSTDIV1_OFFSET 0x28
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_POSTDIV1_SHIFT 28
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_POSTDIV1_MASK GENMASK(29, 28)
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_PREDIV_OFFSET 0x2c
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_PREDIV_SHIFT 0
>> +#define STARFIVE_JH7110_CLK_PLL1_OUT_PREDIV_MASK GENMASK(5, 0)
>> +
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_DACPD_OFFSET 0x2c
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_DACPD_SHIFT 15
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_DACPD_MASK BIT(15)
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_DSMPD_OFFSET 0x2c
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_DSMPD_SHIFT 16
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_DSMPD_MASK BIT(16)
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_FBDIV_OFFSET 0x2c
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_FBDIV_SHIFT 17
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_FBDIV_MASK GENMASK(28, 17)
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_FRAC_OFFSET 0x30
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_FRAC_SHIFT 0
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_FRAC_MASK GENMASK(23, 0)
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_POSTDIV1_OFFSET 0x30
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_POSTDIV1_SHIFT 28
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_POSTDIV1_MASK GENMASK(29, 28)
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_PREDIV_OFFSET 0x34
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_PREDIV_SHIFT 0
>> +#define STARFIVE_JH7110_CLK_PLL2_OUT_PREDIV_MASK GENMASK(5, 0)
>> +
>> +#define JH7110_PLL(_idx, _name, _nums, _val) \
>> +[_idx] = { \
>> + .name = _name, \
>> + .offsets = { \
>> + .dacpd = STARFIVE_##_idx##_DACPD_OFFSET, \
>> + .dsmpd = STARFIVE_##_idx##_DSMPD_OFFSET, \
>> + .fbdiv = STARFIVE_##_idx##_FBDIV_OFFSET, \
>> + .frac = STARFIVE_##_idx##_FRAC_OFFSET, \
>> + .prediv = STARFIVE_##_idx##_PREDIV_OFFSET, \
>> + .postdiv1 = STARFIVE_##_idx##_POSTDIV1_OFFSET, \
>> + }, \
>> + .masks = { \
>> + .dacpd = STARFIVE_##_idx##_DACPD_MASK, \
>> + .dsmpd = STARFIVE_##_idx##_DSMPD_MASK, \
>> + .fbdiv = STARFIVE_##_idx##_FBDIV_MASK, \
>> + .frac = STARFIVE_##_idx##_FRAC_MASK, \
>> + .prediv = STARFIVE_##_idx##_PREDIV_MASK, \
>> + .postdiv1 = STARFIVE_##_idx##_POSTDIV1_MASK, \
>> + }, \
>> + .shifts = { \
>> + .dacpd = STARFIVE_##_idx##_DACPD_SHIFT, \
>> + .dsmpd = STARFIVE_##_idx##_DSMPD_SHIFT, \
>> + .fbdiv = STARFIVE_##_idx##_FBDIV_SHIFT, \
>> + .frac = STARFIVE_##_idx##_FRAC_SHIFT, \
>> + .prediv = STARFIVE_##_idx##_PREDIV_SHIFT, \
>> + .postdiv1 = STARFIVE_##_idx##_POSTDIV1_SHIFT, \
>> + }, \
>> + .preset_val_nums = _nums, \
>> + .preset_val = _val, \
>> +}
>> +
>> +struct jh7110_pll_syscon_offset {
>> + unsigned int dacpd;
>> + unsigned int dsmpd;
>> + unsigned int fbdiv;
>> + unsigned int frac;
>> + unsigned int prediv;
>> + unsigned int postdiv1;
>> +};
>> +
>> +struct jh7110_pll_syscon_mask {
>> + u32 dacpd;
>> + u32 dsmpd;
>> + u32 fbdiv;
>> + u32 frac;
>> + u32 prediv;
>> + u32 postdiv1;
>> +};
>> +
>> +struct jh7110_pll_syscon_shift {
>> + char dacpd;
>> + char dsmpd;
>> + char fbdiv;
>> + char frac;
>> + char prediv;
>> + char postdiv1;
>> +};
>> +
>> +struct jh7110_pll_syscon_val {
>> + unsigned long freq;
>> + u32 prediv;
>> + u32 fbdiv;
>> + u32 postdiv1;
>> +/* Both daxpd and dsmpd set 1 while integer mode */
>> +/* Both daxpd and dsmpd set 0 while fraction mode */
>> + u32 dacpd;
>> + u32 dsmpd;
>> +/* frac value should be decimals multiplied by 2^24 */
>> + u32 frac;
>> +};
>> +
>> +struct jh7110_pll_syscon_conf {
>> + char *name;
>> + struct jh7110_pll_syscon_offset offsets;
>> + struct jh7110_pll_syscon_mask masks;
>> + struct jh7110_pll_syscon_shift shifts;
>> + unsigned int preset_val_nums;
>> + const struct jh7110_pll_syscon_val *preset_val;
>> +};
>> +
>> +struct jh7110_clk_pll_data {
>> + struct clk_hw hw;
>> + unsigned int idx;
>> + unsigned int freq_select_idx;
>> + struct jh7110_pll_syscon_conf conf;
>> +};
>> +
>> +struct jh7110_clk_pll_priv {
>> + unsigned int pll_nums;
>> + struct device *dev;
>> + struct regmap *syscon_regmap;
>> + struct jh7110_clk_pll_data data[];
>> +};
>> +
>> +enum jh7110_pll0_freq_index {
>> + JH7110_PLL0_FREQ_375 = 0,
>> + JH7110_PLL0_FREQ_500,
>> + JH7110_PLL0_FREQ_625,
>> + JH7110_PLL0_FREQ_750,
>> + JH7110_PLL0_FREQ_875,
>> + JH7110_PLL0_FREQ_1000,
>> + JH7110_PLL0_FREQ_1250,
>> + JH7110_PLL0_FREQ_1375,
>> + JH7110_PLL0_FREQ_1500,
>> + JH7110_PLL0_FREQ_MAX
>> +};
>> +
>> +enum jh7110_pll1_freq_index {
>> + JH7110_PLL1_FREQ_1066 = 0,
>> + JH7110_PLL1_FREQ_1200,
>> + JH7110_PLL1_FREQ_1400,
>> + JH7110_PLL1_FREQ_1600,
>> + JH7110_PLL1_FREQ_MAX
>> +};
>> +
>> +enum jh7110_pll2_freq_index {
>> + JH7110_PLL2_FREQ_1188 = 0,
>> + JH7110_PLL2_FREQ_12288,
>> + JH7110_PLL2_FREQ_MAX
>> +};
>> +
>> +/*
>> + * Because the pll frequency is relatively fixed,
>> + * it cannot be set arbitrarily, so it needs a specific configuration.
>> + * PLL0 frequency should be multiple of 125MHz (USB frequency).
>> + */
>> +static const struct jh7110_pll_syscon_val
>> + jh7110_pll0_syscon_val_preset[] = {
>> + [JH7110_PLL0_FREQ_375] = {
>> + .freq = 375000000,
>> + .prediv = 8,
>> + .fbdiv = 125,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> + [JH7110_PLL0_FREQ_500] = {
>> + .freq = 500000000,
>> + .prediv = 6,
>> + .fbdiv = 125,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> + [JH7110_PLL0_FREQ_625] = {
>> + .freq = 625000000,
>> + .prediv = 24,
>> + .fbdiv = 625,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> + [JH7110_PLL0_FREQ_750] = {
>> + .freq = 750000000,
>> + .prediv = 4,
>> + .fbdiv = 125,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> + [JH7110_PLL0_FREQ_875] = {
>> + .freq = 875000000,
>> + .prediv = 24,
>> + .fbdiv = 875,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> + [JH7110_PLL0_FREQ_1000] = {
>> + .freq = 1000000000,
>> + .prediv = 3,
>> + .fbdiv = 125,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> + [JH7110_PLL0_FREQ_1250] = {
>> + .freq = 1250000000,
>> + .prediv = 12,
>> + .fbdiv = 625,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> + [JH7110_PLL0_FREQ_1375] = {
>> + .freq = 1375000000,
>> + .prediv = 24,
>> + .fbdiv = 1375,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> + [JH7110_PLL0_FREQ_1500] = {
>> + .freq = 1500000000,
>> + .prediv = 2,
>> + .fbdiv = 125,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> +};
>> +
>> +static const struct jh7110_pll_syscon_val
>> + jh7110_pll1_syscon_val_preset[] = {
>> + [JH7110_PLL1_FREQ_1066] = {
>> + .freq = 1066000000,
>> + .prediv = 12,
>> + .fbdiv = 533,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> + [JH7110_PLL1_FREQ_1200] = {
>> + .freq = 1200000000,
>> + .prediv = 1,
>> + .fbdiv = 50,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> + [JH7110_PLL1_FREQ_1400] = {
>> + .freq = 1400000000,
>> + .prediv = 6,
>> + .fbdiv = 350,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> + [JH7110_PLL1_FREQ_1600] = {
>> + .freq = 1600000000,
>> + .prediv = 3,
>> + .fbdiv = 200,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> +};
>> +
>> +static const struct jh7110_pll_syscon_val
>> + jh7110_pll2_syscon_val_preset[] = {
>> + [JH7110_PLL2_FREQ_1188] = {
>> + .freq = 1188000000,
>> + .prediv = 2,
>> + .fbdiv = 99,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> + [JH7110_PLL2_FREQ_12288] = {
>> + .freq = 1228800000,
>> + .prediv = 5,
>> + .fbdiv = 256,
>> + .postdiv1 = 1,
>> + .dacpd = 1,
>> + .dsmpd = 1,
>> + },
>> +};
>> +
>> +#endif
>> --
>> 2.25.1
>
> In general this driver is overly generic even though it is a driver
> specific to the JH7110 SoC. Rather than try to explain all the ways
> you can simplify it, I decided it would be easier to show you:
>
> https://github.com/esmil/linux/commit/9b7f325267c9a760eda6612c7ffbf22366790878
>
> It has all the same functionality, fixes all of the above and saves
> more than 100 lines of code, so please use that for your next
> revision.
>
Thanks for you suggestions. I will fix it by referring to these.
Best regards,
Xingyu Wu
More information about the linux-riscv
mailing list