[PATCH v4 12/19] clk: starfive: Add StarFive JH7110 always-on clock driver
Emil Renner Berthing
emil.renner.berthing at canonical.com
Sun Feb 26 09:34:52 PST 2023
On Tue, 21 Feb 2023 at 03:47, Hal Feng <hal.feng at starfivetech.com> wrote:
> From: Emil Renner Berthing <kernel at esmil.dk>
>
> Add driver for the StarFive JH7110 always-on clock controller
> and register an auxiliary device for always-on reset controller
> which is named as "reset-aon".
>
> Reported-by: kernel test robot <lkp at intel.com>
> Signed-off-by: Emil Renner Berthing <kernel at esmil.dk>
> Co-developed-by: Hal Feng <hal.feng at starfivetech.com>
> Signed-off-by: Hal Feng <hal.feng at starfivetech.com>
> ---
> drivers/clk/starfive/Kconfig | 11 ++
> drivers/clk/starfive/Makefile | 1 +
> .../clk/starfive/clk-starfive-jh7110-aon.c | 156 ++++++++++++++++++
> 3 files changed, 168 insertions(+)
> create mode 100644 drivers/clk/starfive/clk-starfive-jh7110-aon.c
>
> diff --git a/drivers/clk/starfive/Kconfig b/drivers/clk/starfive/Kconfig
> index 4640d0665d1c..2aa664f2cdee 100644
> --- a/drivers/clk/starfive/Kconfig
> +++ b/drivers/clk/starfive/Kconfig
> @@ -31,3 +31,14 @@ config CLK_STARFIVE_JH7110_SYS
> help
> Say yes here to support the system clock controller on the
> StarFive JH7110 SoC.
> +
> +config CLK_STARFIVE_JH7110_AON
> + tristate "StarFive JH7110 always-on clock support"
> + depends on CLK_STARFIVE_JH7110_SYS
> + select AUXILIARY_BUS
> + select CLK_STARFIVE_JH71X0
> + select RESET_STARFIVE_JH7110
> + default CLK_STARFIVE_JH7110_SYS
As far as I can tell the JH7110 boots fine without this driver and it
already depends on the _SYS driver above, so please do
default m if SOC_STARFIVE
And consider helping Conor by changing all the SOC_STARFIVE instances
to ARCH_STARFIVE for the next version.
> + help
> + Say yes here to support the always-on clock controller on the
> + StarFive JH7110 SoC.
> diff --git a/drivers/clk/starfive/Makefile b/drivers/clk/starfive/Makefile
> index 5ca4e887fb9c..f3df7d957b1e 100644
> --- a/drivers/clk/starfive/Makefile
> +++ b/drivers/clk/starfive/Makefile
> @@ -5,3 +5,4 @@ obj-$(CONFIG_CLK_STARFIVE_JH7100) += clk-starfive-jh7100.o
> obj-$(CONFIG_CLK_STARFIVE_JH7100_AUDIO) += clk-starfive-jh7100-audio.o
>
> obj-$(CONFIG_CLK_STARFIVE_JH7110_SYS) += clk-starfive-jh7110-sys.o
> +obj-$(CONFIG_CLK_STARFIVE_JH7110_AON) += clk-starfive-jh7110-aon.o
> diff --git a/drivers/clk/starfive/clk-starfive-jh7110-aon.c b/drivers/clk/starfive/clk-starfive-jh7110-aon.c
> new file mode 100644
> index 000000000000..da808dc93048
> --- /dev/null
> +++ b/drivers/clk/starfive/clk-starfive-jh7110-aon.c
> @@ -0,0 +1,156 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * StarFive JH7110 Always-On Clock Driver
> + *
> + * Copyright (C) 2022 Emil Renner Berthing <kernel at esmil.dk>
> + * Copyright (C) 2022 StarFive Technology Co., Ltd.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/clk-provider.h>
> +#include <linux/io.h>
> +#include <linux/platform_device.h>
> +
> +#include <dt-bindings/clock/starfive,jh7110-crg.h>
> +
> +#include "clk-starfive-jh71x0.h"
> +
> +/* external clocks */
> +#define JH7110_AONCLK_OSC (JH7110_AONCLK_END + 0)
> +#define JH7110_AONCLK_RTC_OSC (JH7110_AONCLK_END + 1)
> +#define JH7110_AONCLK_GMAC0_RMII_REFIN (JH7110_AONCLK_END + 2)
> +#define JH7110_AONCLK_GMAC0_RGMII_RXIN (JH7110_AONCLK_END + 3)
> +#define JH7110_AONCLK_STG_AXIAHB (JH7110_AONCLK_END + 4)
> +#define JH7110_AONCLK_APB_BUS (JH7110_AONCLK_END + 5)
> +#define JH7110_AONCLK_GMAC0_GTXCLK (JH7110_AONCLK_END + 6)
> +
> +static const struct jh71x0_clk_data jh7110_aonclk_data[] = {
> + /* source */
> + JH71X0__DIV(JH7110_AONCLK_OSC_DIV4, "osc_div4", 4, JH7110_AONCLK_OSC),
> + JH71X0__MUX(JH7110_AONCLK_APB_FUNC, "apb_func", 2,
> + JH7110_AONCLK_OSC_DIV4,
> + JH7110_AONCLK_OSC),
> + /* gmac0 */
> + JH71X0_GATE(JH7110_AONCLK_GMAC0_AHB, "gmac0_ahb", 0, JH7110_AONCLK_STG_AXIAHB),
> + JH71X0_GATE(JH7110_AONCLK_GMAC0_AXI, "gmac0_axi", 0, JH7110_AONCLK_STG_AXIAHB),
> + JH71X0__DIV(JH7110_AONCLK_GMAC0_RMII_RTX, "gmac0_rmii_rtx", 30,
> + JH7110_AONCLK_GMAC0_RMII_REFIN),
> + JH71X0_GMUX(JH7110_AONCLK_GMAC0_TX, "gmac0_tx", 0, 2,
> + JH7110_AONCLK_GMAC0_GTXCLK,
> + JH7110_AONCLK_GMAC0_RMII_RTX),
> + JH71X0__INV(JH7110_AONCLK_GMAC0_TX_INV, "gmac0_tx_inv", JH7110_AONCLK_GMAC0_TX),
> + JH71X0__MUX(JH7110_AONCLK_GMAC0_RX, "gmac0_rx", 2,
> + JH7110_AONCLK_GMAC0_RGMII_RXIN,
> + JH7110_AONCLK_GMAC0_RMII_RTX),
> + JH71X0__INV(JH7110_AONCLK_GMAC0_RX_INV, "gmac0_rx_inv", JH7110_AONCLK_GMAC0_RX),
> + /* otpc */
> + JH71X0_GATE(JH7110_AONCLK_OTPC_APB, "otpc_apb", CLK_IGNORE_UNUSED, JH7110_AONCLK_APB_BUS),
> + /* rtc */
> + JH71X0_GATE(JH7110_AONCLK_RTC_APB, "rtc_apb", CLK_IGNORE_UNUSED, JH7110_AONCLK_APB_BUS),
> + JH71X0__DIV(JH7110_AONCLK_RTC_INTERNAL, "rtc_internal", 1022, JH7110_AONCLK_OSC),
> + JH71X0__MUX(JH7110_AONCLK_RTC_32K, "rtc_32k", 2,
> + JH7110_AONCLK_RTC_OSC,
> + JH7110_AONCLK_RTC_INTERNAL),
> + JH71X0_GATE(JH7110_AONCLK_RTC_CAL, "rtc_cal", 0, JH7110_AONCLK_OSC),
> +};
This list also contains instances of the CLK_IGNORE_UNUSED flag. Again
please go through them and figure out which clocks are critical and
which are fine to turn off when not used.
> +
> +static struct clk_hw *jh7110_aonclk_get(struct of_phandle_args *clkspec, void *data)
> +{
> + struct jh71x0_clk_priv *priv = data;
> + unsigned int idx = clkspec->args[0];
> +
> + if (idx < JH7110_AONCLK_END)
> + return &priv->reg[idx].hw;
> +
> + return ERR_PTR(-EINVAL);
> +}
> +
> +static int jh7110_aoncrg_probe(struct platform_device *pdev)
> +{
> + struct jh71x0_clk_priv *priv;
> + unsigned int idx;
> + int ret;
> +
> + priv = devm_kzalloc(&pdev->dev,
> + struct_size(priv, reg, JH7110_AONCLK_END),
> + GFP_KERNEL);
> + if (!priv)
> + return -ENOMEM;
> +
> + spin_lock_init(&priv->rmw_lock);
> + priv->dev = &pdev->dev;
> + priv->base = devm_platform_ioremap_resource(pdev, 0);
> + if (IS_ERR(priv->base))
> + return PTR_ERR(priv->base);
> +
> + dev_set_drvdata(priv->dev, (void *)(&priv->base));
> +
> + for (idx = 0; idx < JH7110_AONCLK_END; idx++) {
> + u32 max = jh7110_aonclk_data[idx].max;
> + struct clk_parent_data parents[4] = {};
> + struct clk_init_data init = {
> + .name = jh7110_aonclk_data[idx].name,
> + .ops = starfive_jh71x0_clk_ops(max),
> + .parent_data = parents,
> + .num_parents =
> + ((max & JH71X0_CLK_MUX_MASK) >> JH71X0_CLK_MUX_SHIFT) + 1,
> + .flags = jh7110_aonclk_data[idx].flags,
> + };
> + struct jh71x0_clk *clk = &priv->reg[idx];
> + unsigned int i;
> +
> + for (i = 0; i < init.num_parents; i++) {
> + unsigned int pidx = jh7110_aonclk_data[idx].parents[i];
> +
> + if (pidx < JH7110_AONCLK_END)
> + parents[i].hw = &priv->reg[pidx].hw;
> + else if (pidx == JH7110_AONCLK_OSC)
> + parents[i].fw_name = "osc";
> + else if (pidx == JH7110_AONCLK_RTC_OSC)
> + parents[i].fw_name = "rtc_osc";
> + else if (pidx == JH7110_AONCLK_GMAC0_RMII_REFIN)
> + parents[i].fw_name = "gmac0_rmii_refin";
> + else if (pidx == JH7110_AONCLK_GMAC0_RGMII_RXIN)
> + parents[i].fw_name = "gmac0_rgmii_rxin";
> + else if (pidx == JH7110_AONCLK_STG_AXIAHB)
> + parents[i].fw_name = "stg_axiahb";
> + else if (pidx == JH7110_AONCLK_APB_BUS)
> + parents[i].fw_name = "apb_bus";
> + else if (pidx == JH7110_AONCLK_GMAC0_GTXCLK)
> + parents[i].fw_name = "gmac0_gtxclk";
> + }
> +
> + clk->hw.init = &init;
> + clk->idx = idx;
> + clk->max_div = max & JH71X0_CLK_DIV_MASK;
> +
> + ret = devm_clk_hw_register(&pdev->dev, &clk->hw);
> + if (ret)
> + return ret;
> + }
> +
> + ret = devm_of_clk_add_hw_provider(&pdev->dev, jh7110_aonclk_get, priv);
> + if (ret)
> + return ret;
> +
> + return jh7110_reset_controller_register(priv, "reset-aon", 1);
> +}
> +
> +static const struct of_device_id jh7110_aoncrg_match[] = {
> + { .compatible = "starfive,jh7110-aoncrg" },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, jh7110_aoncrg_match);
> +
> +static struct platform_driver jh7110_aoncrg_driver = {
> + .probe = jh7110_aoncrg_probe,
> + .driver = {
> + .name = "clk-starfive-jh7110-aon",
> + .of_match_table = jh7110_aoncrg_match,
> + },
> +};
> +module_platform_driver(jh7110_aoncrg_driver);
> +
> +MODULE_AUTHOR("Emil Renner Berthing");
> +MODULE_DESCRIPTION("StarFive JH7110 always-on clock driver");
> +MODULE_LICENSE("GPL");
> --
> 2.38.1
>
More information about the linux-riscv
mailing list