[PATCH v1 3/3] riscv: dts: starfive: jh7110: Add PLL clock node

[Krzysztof Kozlowski]

On 23/02/2023 10:03, Xingyu Wu wrote:
> On 2023/2/23 16:52, Krzysztof Kozlowski wrote:
>> On 23/02/2023 09:47, Xingyu Wu wrote:
>>> On 2023/2/22 17:09, Krzysztof Kozlowski wrote:
>>>> On 21/02/2023 15:11, Xingyu Wu wrote:
>>>>> Add the PLL clock node for the Starfive JH7110 SoC and
>>>>> modify the SYSCRG node to add PLL clocks.
>>>>>
>>>>> Signed-off-by: Xingyu Wu <xingyu.wu at starfivetech.com>
>>>>> ---
>>>>>  arch/riscv/boot/dts/starfive/jh7110.dtsi | 15 +++++++++++++--
>>>>>  1 file changed, 13 insertions(+), 2 deletions(-)
>>>>>
>>>>> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
>>>>> index b6612c53d0d2..0cb8d86ebce5 100644
>>>>> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
>>>>> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
>>>>> @@ -461,12 +461,16 @@ syscrg: clock-controller at 13020000 {
>>>>>  				 <&gmac1_rgmii_rxin>,
>>>>>  				 <&i2stx_bclk_ext>, <&i2stx_lrck_ext>,
>>>>>  				 <&i2srx_bclk_ext>, <&i2srx_lrck_ext>,
>>>>> -				 <&tdm_ext>, <&mclk_ext>;
>>>>> +				 <&tdm_ext>, <&mclk_ext>,
>>>>> +				 <&pllclk JH7110_CLK_PLL0_OUT>,
>>>>> +				 <&pllclk JH7110_CLK_PLL1_OUT>,
>>>>> +				 <&pllclk JH7110_CLK_PLL2_OUT>;
>>>>>  			clock-names = "osc", "gmac1_rmii_refin",
>>>>>  				      "gmac1_rgmii_rxin",
>>>>>  				      "i2stx_bclk_ext", "i2stx_lrck_ext",
>>>>>  				      "i2srx_bclk_ext", "i2srx_lrck_ext",
>>>>> -				      "tdm_ext", "mclk_ext";
>>>>> +				      "tdm_ext", "mclk_ext",
>>>>> +				      "pll0_out", "pll1_out", "pll2_out";
>>>>>  			#clock-cells = <1>;
>>>>>  			#reset-cells = <1>;
>>>>>  		};
>>>>> @@ -476,6 +480,13 @@ sys_syscon: syscon at 13030000 {
>>>>>  			reg = <0x0 0x13030000 0x0 0x1000>;
>>>>>  		};
>>>>>  
>>>>> +		pllclk: pll-clock-controller {
>>>>
>>>> Does not look like you tested the DTS against bindings. Please run `make
>>>> dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
>>>> for instructions). You should see here warnings of mixing non-MMIO nodes
>>>> in MMIO-bus.
>>>>
>>>
>>> Oh I cherry-pick the commit of syscon node and it also include the MMC node.
>>> I will remove the MMC node. 
>>> I used dtbs_check and get the error 'should not be valid under {'type': 'object'}',
>>> If I move this node out of the 'soc' node, the dtbs_check will be pass.
>>> Is it OK to move the PLL node out of the 'soc' node? Thanks.
>>
>> Shall it be out side of soc? How it can then do anything with registers?
>> This does not look like correct representation of hardware.
> 
> The error appears to be due to a lack of reg base about PLL node. PLL do something with register
> by 'sys_syscon' node and the syscon node is in the soc node.

Again: And how is this correct representation of hardware?

Best regards,
Krzysztof