[PATCH v1 3/3] riscv: dts: starfive: jh7110: Add PLL clock node

[Xingyu Wu]

On 2023/2/22 17:09, Krzysztof Kozlowski wrote:
> On 21/02/2023 15:11, Xingyu Wu wrote:
>> Add the PLL clock node for the Starfive JH7110 SoC and
>> modify the SYSCRG node to add PLL clocks.
>> 
>> Signed-off-by: Xingyu Wu <xingyu.wu at starfivetech.com>
>> ---
>>  arch/riscv/boot/dts/starfive/jh7110.dtsi | 15 +++++++++++++--
>>  1 file changed, 13 insertions(+), 2 deletions(-)
>> 
>> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
>> index b6612c53d0d2..0cb8d86ebce5 100644
>> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
>> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
>> @@ -461,12 +461,16 @@ syscrg: clock-controller at 13020000 {
>>  				 <&gmac1_rgmii_rxin>,
>>  				 <&i2stx_bclk_ext>, <&i2stx_lrck_ext>,
>>  				 <&i2srx_bclk_ext>, <&i2srx_lrck_ext>,
>> -				 <&tdm_ext>, <&mclk_ext>;
>> +				 <&tdm_ext>, <&mclk_ext>,
>> +				 <&pllclk JH7110_CLK_PLL0_OUT>,
>> +				 <&pllclk JH7110_CLK_PLL1_OUT>,
>> +				 <&pllclk JH7110_CLK_PLL2_OUT>;
>>  			clock-names = "osc", "gmac1_rmii_refin",
>>  				      "gmac1_rgmii_rxin",
>>  				      "i2stx_bclk_ext", "i2stx_lrck_ext",
>>  				      "i2srx_bclk_ext", "i2srx_lrck_ext",
>> -				      "tdm_ext", "mclk_ext";
>> +				      "tdm_ext", "mclk_ext",
>> +				      "pll0_out", "pll1_out", "pll2_out";
>>  			#clock-cells = <1>;
>>  			#reset-cells = <1>;
>>  		};
>> @@ -476,6 +480,13 @@ sys_syscon: syscon at 13030000 {
>>  			reg = <0x0 0x13030000 0x0 0x1000>;
>>  		};
>>  
>> +		pllclk: pll-clock-controller {
> 
> Does not look like you tested the DTS against bindings. Please run `make
> dtbs_check` (see Documentation/devicetree/bindings/writing-schema.rst
> for instructions). You should see here warnings of mixing non-MMIO nodes
> in MMIO-bus.
> 

Oh I cherry-pick the commit of syscon node and it also include the MMC node.
I will remove the MMC node. 
I used dtbs_check and get the error 'should not be valid under {'type': 'object'}',
If I move this node out of the 'soc' node, the dtbs_check will be pass.
Is it OK to move the PLL node out of the 'soc' node? Thanks.

Best regards,
Xingyu Wu