[PATCH v4 5/7] net: stmmac: Add glue layer for StarFive JH7110 SoCs
yanhong wang
yanhong.wang at starfivetech.com
Mon Feb 20 18:27:05 PST 2023
add samin.guo at starfivetech.com to loop.
On 2023/2/16 18:53, Emil Renner Berthing wrote:
> On Wed, 18 Jan 2023 at 07:20, Yanhong Wang
> <yanhong.wang at starfivetech.com> wrote:
>>
>> This adds StarFive dwmac driver support on the StarFive JH7110 SoCs.
>>
>> Signed-off-by: Yanhong Wang <yanhong.wang at starfivetech.com>
>> Co-developed-by: Emil Renner Berthing <kernel at esmil.dk>
>> Signed-off-by: Emil Renner Berthing <kernel at esmil.dk>
>> ---
>> MAINTAINERS | 1 +
>> drivers/net/ethernet/stmicro/stmmac/Kconfig | 12 ++
>> drivers/net/ethernet/stmicro/stmmac/Makefile | 1 +
>> .../stmicro/stmmac/dwmac-starfive-plat.c | 118 ++++++++++++++++++
>> 4 files changed, 132 insertions(+)
>> create mode 100644 drivers/net/ethernet/stmicro/stmmac/dwmac-starfive-plat.c
>>
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 56be59bb09f7..5b50b52d3dbb 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -19609,6 +19609,7 @@ F: include/dt-bindings/clock/starfive*
>> STARFIVE DWMAC GLUE LAYER
>> M: Yanhong Wang <yanhong.wang at starfivetech.com>
>> S: Maintained
>> +F: Documentation/devicetree/bindings/net/dwmac-starfive-plat.c
>> F: Documentation/devicetree/bindings/net/starfive,jh7110-dwmac.yaml
>>
>> STARFIVE PINCTRL DRIVER
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/Kconfig b/drivers/net/ethernet/stmicro/stmmac/Kconfig
>> index 31ff35174034..f9a4ad4abd54 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/Kconfig
>> +++ b/drivers/net/ethernet/stmicro/stmmac/Kconfig
>> @@ -235,6 +235,18 @@ config DWMAC_INTEL_PLAT
>> the stmmac device driver. This driver is used for the Intel Keem Bay
>> SoC.
>>
>> +config DWMAC_STARFIVE_PLAT
>> + tristate "StarFive dwmac support"
>> + depends on OF && COMMON_CLK
>> + depends on STMMAC_ETH
>> + default SOC_STARFIVE
>> + help
>> + Support for ethernet controllers on StarFive RISC-V SoCs
>> +
>> + This selects the StarFive platform specific glue layer support for
>> + the stmmac device driver. This driver is used for StarFive JH7110
>> + ethernet controller.
>> +
>> config DWMAC_VISCONTI
>> tristate "Toshiba Visconti DWMAC support"
>> default ARCH_VISCONTI
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/Makefile b/drivers/net/ethernet/stmicro/stmmac/Makefile
>> index d4e12e9ace4f..a63ab0ab5071 100644
>> --- a/drivers/net/ethernet/stmicro/stmmac/Makefile
>> +++ b/drivers/net/ethernet/stmicro/stmmac/Makefile
>> @@ -31,6 +31,7 @@ obj-$(CONFIG_DWMAC_DWC_QOS_ETH) += dwmac-dwc-qos-eth.o
>> obj-$(CONFIG_DWMAC_INTEL_PLAT) += dwmac-intel-plat.o
>> obj-$(CONFIG_DWMAC_GENERIC) += dwmac-generic.o
>> obj-$(CONFIG_DWMAC_IMX8) += dwmac-imx.o
>> +obj-$(CONFIG_DWMAC_STARFIVE_PLAT) += dwmac-starfive-plat.o
>
> Hi Yanhong,
>
> For the next version could you please drop the _PLAT from the config
> symbol and -plat from filename. I know the intel wrapper does the
> same, but it's the only one, so lets do like the majority of other
> wrappers and not add more different ways of doing things.
>
Thanks. I will fix.
>> obj-$(CONFIG_DWMAC_VISCONTI) += dwmac-visconti.o
>> stmmac-platform-objs:= stmmac_platform.o
>> dwmac-altr-socfpga-objs := altr_tse_pcs.o dwmac-socfpga.o
>> diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-starfive-plat.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-starfive-plat.c
>> new file mode 100644
>> index 000000000000..e441d920933a
>> --- /dev/null
>> +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-starfive-plat.c
>> @@ -0,0 +1,118 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * StarFive DWMAC platform driver
>> + *
>> + * Copyright(C) 2022 StarFive Technology Co., Ltd.
>> + *
>> + */
>> +
>> +#include <linux/of_device.h>
>> +
>> +#include "stmmac_platform.h"
>> +
>> +struct starfive_dwmac {
>> + struct device *dev;
>> + struct clk *clk_tx;
>> + struct clk *clk_gtx;
>> + struct clk *clk_gtxc;
>> +};
>
> I like this name. For the next version could you also
> s/starfive_eth_plat_/starfive_dwmac_/ on the function/struct names
> below for consistency.
>
I will fix.
>> +
>> +static void starfive_eth_plat_fix_mac_speed(void *priv, unsigned int speed)
>> +{
>> + struct starfive_dwmac *dwmac = priv;
>> + unsigned long rate;
>> + int err;
>> +
>> + rate = clk_get_rate(dwmac->clk_gtx);
>> +
>> + switch (speed) {
>> + case SPEED_1000:
>> + rate = 125000000;
>> + break;
>> + case SPEED_100:
>> + rate = 25000000;
>> + break;
>> + case SPEED_10:
>> + rate = 2500000;
>> + break;
>> + default:
>> + dev_err(dwmac->dev, "invalid speed %u\n", speed);
>> + break;
>> + }
>> +
>> + err = clk_set_rate(dwmac->clk_gtx, rate);
>> + if (err)
>> + dev_err(dwmac->dev, "failed to set tx rate %lu\n", rate);
>> +}
>> +
>> +static int starfive_eth_plat_probe(struct platform_device *pdev)
>> +{
>> + struct plat_stmmacenet_data *plat_dat;
>> + struct stmmac_resources stmmac_res;
>> + struct starfive_dwmac *dwmac;
>> + int err;
>> +
>> + err = stmmac_get_platform_resources(pdev, &stmmac_res);
>> + if (err)
>> + return err;
>> +
>> + plat_dat = stmmac_probe_config_dt(pdev, stmmac_res.mac);
>> + if (IS_ERR(plat_dat)) {
>> + dev_err(&pdev->dev, "dt configuration failed\n");
>> + return PTR_ERR(plat_dat);
>> + }
>> +
>> + dwmac = devm_kzalloc(&pdev->dev, sizeof(*dwmac), GFP_KERNEL);
>> + if (!dwmac)
>> + return -ENOMEM;
>> +
>> + dwmac->clk_tx = devm_clk_get_enabled(&pdev->dev, "tx");
>> + if (IS_ERR(dwmac->clk_tx))
>> + return dev_err_probe(&pdev->dev, PTR_ERR(dwmac->clk_tx),
>> + "error getting tx clock\n");
>> +
>> + dwmac->clk_gtx = devm_clk_get_enabled(&pdev->dev, "gtx");
>> + if (IS_ERR(dwmac->clk_gtx))
>> + return dev_err_probe(&pdev->dev, PTR_ERR(dwmac->clk_gtx),
>> + "error getting gtx clock\n");
>> +
>> + dwmac->clk_gtxc = devm_clk_get_enabled(&pdev->dev, "gtxc");
>> + if (IS_ERR(dwmac->clk_gtxc))
>> + return dev_err_probe(&pdev->dev, PTR_ERR(dwmac->clk_gtxc),
>> + "error getting gtxc clock\n");
>> +
>> + dwmac->dev = &pdev->dev;
>> + plat_dat->fix_mac_speed = starfive_eth_plat_fix_mac_speed;
>> + plat_dat->init = NULL;
>> + plat_dat->bsp_priv = dwmac;
>> + plat_dat->dma_cfg->dche = true;
>> +
>> + err = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
>> + if (err) {
>> + stmmac_remove_config_dt(pdev, plat_dat);
>> + return err;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static const struct of_device_id starfive_eth_plat_match[] = {
>> + { .compatible = "starfive,jh7110-dwmac" },
>> + { }
>> +};
>> +
>> +static struct platform_driver starfive_eth_plat_driver = {
>> + .probe = starfive_eth_plat_probe,
>> + .remove = stmmac_pltfr_remove,
>> + .driver = {
>> + .name = "starfive-eth-plat",
>> + .pm = &stmmac_pltfr_pm_ops,
>> + .of_match_table = starfive_eth_plat_match,
>> + },
>> +};
>> +
>> +module_platform_driver(starfive_eth_plat_driver);
>> +
>> +MODULE_LICENSE("GPL");
>> +MODULE_DESCRIPTION("StarFive DWMAC platform driver");
>> +MODULE_AUTHOR("Yanhong Wang <yanhong.wang at starfivetech.com>");
>> --
>> 2.17.1
>>
>>
>> _______________________________________________
>> linux-riscv mailing list
>> linux-riscv at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-riscv
More information about the linux-riscv
mailing list