[PATCH v4 3/4] riscv: dts: starfive: Add mmc node

[Emil Renner Berthing]

On Wed, 15 Feb 2023 at 12:35, William Qiu <william.qiu at starfivetech.com> wrote:
>
> Add the mmc node for the StarFive JH7110 SoC.
> Set mmco node to emmc and set mmc1 node to sd.
>
> Signed-off-by: William Qiu <william.qiu at starfivetech.com>
> ---
>  .../jh7110-starfive-visionfive-2.dtsi         | 23 +++++++++
>  arch/riscv/boot/dts/starfive/jh7110.dtsi      | 47 +++++++++++++++++++
>  2 files changed, 70 insertions(+)
>
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> index c60280b89c73..e1a0248e907f 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> @@ -42,6 +42,29 @@ &rtc_osc {
>         clock-frequency = <32768>;
>  };
>
> +&mmc0 {
> +       max-frequency = <100000000>;
> +       bus-width = <8>;
> +       cap-mmc-highspeed;
> +       mmc-ddr-1_8v;
> +       mmc-hs200-1_8v;
> +       non-removable;
> +       cap-mmc-hw-reset;
> +       post-power-on-delay-ms = <200>;
> +       status = "okay";
> +};
> +
> +&mmc1 {
> +       max-frequency = <100000000>;
> +       bus-width = <4>;
> +       no-sdio;
> +       no-mmc;
> +       broken-cd;
> +       cap-sd-highspeed;
> +       post-power-on-delay-ms = <200>;
> +       status = "okay";
> +};
> +
>  &gmac0_rmii_refin {
>         clock-frequency = <50000000>;
>  };
> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> index 64d260ea1f29..17f7b3ee6ca3 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> @@ -314,6 +314,11 @@ uart2: serial at 10020000 {
>                         status = "disabled";
>                 };
>
> +               stg_syscon: syscon at 10240000 {
> +                       compatible = "starfive,jh7110-stg-syscon", "syscon";
> +                       reg = <0x0 0x10240000 0x0 0x1000>;
> +               };
> +
>                 uart3: serial at 12000000 {
>                         compatible = "snps,dw-apb-uart";
>                         reg = <0x0 0x12000000 0x0 0x10000>;
> @@ -370,6 +375,11 @@ syscrg: clock-controller at 13020000 {
>                         #reset-cells = <1>;
>                 };
>
> +               sys_syscon: syscon at 13030000 {
> +                       compatible = "starfive,jh7110-sys-syscon", "syscon";
> +                       reg = <0x0 0x13030000 0x0 0x1000>;
> +               };
> +
>                 gpio: gpio at 13040000 {
>                         compatible = "starfive,jh7110-sys-pinctrl";
>                         reg = <0x0 0x13040000 0x0 0x10000>;
> @@ -397,6 +407,11 @@ aoncrg: clock-controller at 17000000 {
>                         #reset-cells = <1>;
>                 };
>
> +               aon_syscon: syscon at 17010000 {
> +                       compatible = "starfive,jh7110-aon-syscon", "syscon";
> +                       reg = <0x0 0x17010000 0x0 0x1000>;
> +               };
> +
>                 gpioa: gpio at 17020000 {
>                         compatible = "starfive,jh7110-aon-pinctrl";
>                         reg = <0x0 0x17020000 0x0 0x10000>;
> @@ -407,5 +422,37 @@ gpioa: gpio at 17020000 {
>                         gpio-controller;
>                         #gpio-cells = <2>;
>                 };
> +
> +               mmc0: mmc at 16010000 {
> +                       compatible = "starfive,jh7110-mmc";
> +                       reg = <0x0 0x16010000 0x0 0x10000>;
> +                       clocks = <&syscrg JH7110_SYSCLK_SDIO0_AHB>,
> +                                <&syscrg JH7110_SYSCLK_SDIO0_SDCARD>;
> +                       clock-names = "biu","ciu";
> +                       resets = <&syscrg JH7110_SYSRST_SDIO0_AHB>;
> +                       reset-names = "reset";
> +                       interrupts = <74>;
> +                       fifo-depth = <32>;
> +                       fifo-watermark-aligned;
> +                       data-addr = <0>;
> +                       starfive,sysreg = <&sys_syscon 0x14 0x1a 0x7c000000>;
> +                       status = "disabled";
> +               };
> +
> +               mmc1: mmc at 16020000 {
> +                       compatible = "starfive,jh7110-mmc";
> +                       reg = <0x0 0x16020000 0x0 0x10000>;
> +                       clocks = <&syscrg JH7110_SYSCLK_SDIO1_AHB>,
> +                                <&syscrg JH7110_SYSCLK_SDIO1_SDCARD>;
> +                       clock-names = "biu","ciu";
> +                       resets = <&syscrg JH7110_SYSRST_SDIO1_AHB>;
> +                       reset-names = "reset";
> +                       interrupts = <75>;
> +                       fifo-depth = <32>;
> +                       fifo-watermark-aligned;
> +                       data-addr = <0>;
> +                       starfive,sysreg = <&sys_syscon 0x9c 0x1 0x3e>;
> +                       status = "disabled";
> +               };

Hi William,

These nodes still don't seem to be sorted by address, eg. by the
number after the @
Also please move the dt-binding patch before this one, so dtb_check
won't fail no matter where git bisect happens to land.

/Emil

>         };
>  };
> --
> 2.34.1
>
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv