[PATCH] riscv: dts: nezha-d1: add gpio-line-names

[Trevor Woerner]

Hi Conor,

Thank you for your review!

On Wed 2023-02-08 @ 04:43:06 PM, Conor Dooley wrote:
> On Tue, Feb 07, 2023 at 08:45:03PM -0500, Trevor Woerner wrote:
> > Add descriptive names so users can associate specific lines with their
> > respective pins on the 40-pin header according to the schematics found at:
> > 
> > 	http://dl.linux-sunxi.org/D1/D1_Nezha_development_board_schematic_diagram_20210224.pdf
> 
> Dunno about the sunxi folk, but ideally that'd be a Link: tag IMO.

Okay, np.

> > 
> > Signed-off-by: Trevor Woerner <twoerner at gmail.com>
> > ---
> >  .../boot/dts/allwinner/sun20i-d1-nezha.dts    | 53 +++++++++++++++++++
> >  1 file changed, 53 insertions(+)
> > 
> > diff --git a/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
> > index a0769185be97..33489c7619cb 100644
> > --- a/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
> > +++ b/arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dts
> > @@ -90,6 +90,15 @@ pcf8574a: gpio at 38 {
> >  		gpio-controller;
> >  		#gpio-cells = <2>;
> >  		#interrupt-cells = <2>;
> > +		gpio-line-names =
> > +			"pin13 [PP0,gpio8] ",
> > +			"pin16 [PP1,gpio10]",
> > +			"pin18 [PP2,gpio11]",
> > +			"pin26 [PP3,gpio17]",
> > +			"pin22 [PP4,gpio14]",
> > +			"pin28 [PP5,gpio19]",
> > +			"pin37 [PP6,gpio23]",
> > +			"pin11 [PP7,gpio6] ";
> 
> dtbs_check does not like this:
> arch/riscv/boot/dts/allwinner/sun20i-d1-nezha.dtb: gpio at 38: 'gpio-line-names' does not match any of the regexes: '^(.+-hog(-[0-9]+)?)$', 'pinctrl-[0-9]+'
>         From schema: Documentation/devicetree/bindings/gpio/nxp,pcf8575.yaml
> 
> >  	};
> >  };

Okay, I'll look for other examples of giving names to io-expanders to see
what's needed to keep dtc happy.

> >  
> > @@ -164,3 +173,47 @@ &usbphy {
> >  	usb1_vbus-supply = <&reg_vcc>;
> >  	status = "okay";
> >  };
> > +
> > +&pio {
> > +	gpio-line-names =
> > +		/* Port A */
> > +		"", "", "", "", "", "", "", "",
> > +		"", "", "", "", "", "", "", "",
> > +		"", "", "", "", "", "", "", "",
> > +		"", "", "", "", "", "", "", "",
> > +		/* Port B */
> > +		"pin5  [PB0, gpio2/twi2-sck]",
> > +		"pin3  [PB1, gpio1/twi2-sda]",
> > +		"",
> > +		"pin38 [PB3, gpio24/i2s2-din]",
> > +		"pin40 [PB4, gpio25/i2s2-dout]",
> > +		"pin12 [PB5, gpio7/i2s-clk]",
> > +		"pin35 [PB6, gpio22/i2s2-lrck]",
> > +		"",
> > +		"pin8  [PB8, gpio4/uart0-txd]",
> > +		"pin10 [PB9, gpio5/uart0-rxd]",
> > +		"",
> > +		"",
> > +		"pin15 [PB12,gpio9]",
> 
> Why not pick a consistent styling w.r.t. the space between PB#, & gpio?

I thought it looked better when doing:

	nezha-allwinner-d1:~# gpioinfo
	gpiochip0 - 224 lines:
		...
		line  32: "pin5  [PB0, gpio2/twi2-sck]" kernel input active-high [used]
		line  33: "pin3  [PB1, gpio1/twi2-sda]" kernel input active-high [used]
		line  34:      unnamed  "interrupt"   input  active-high [used]
		line  35: "pin38 [PB3, gpio24/i2s2-din]" unused input active-high
		line  36: "pin40 [PB4, gpio25/i2s2-dout]" unused input active-high
		line  37: "pin12 [PB5, gpio7/i2s-clk]" unused input active-high
		line  38: "pin35 [PB6, gpio22/i2s2-lrck]" unused input active-high
		line  39:      unnamed       unused   input  active-high
		line  40: "pin8  [PB8, gpio4/uart0-txd]" kernel input active-high [used]
		line  41: "pin10 [PB9, gpio5/uart0-rxd]" kernel input active-high [used]
		...

I guess "better" is subjective :-)

I'll do a v2, thanks!