[PATCH v3 2/5] dt-bindings: pinctrl: Add StarFive JH7110 sys pinctrl

[Hal Feng]

On Tue, 20 Dec 2022 14:19:20 -0600, Rob Herring wrote:
> On Tue, Dec 20, 2022 at 08:55:26AM +0800, Hal Feng wrote:
>> From: Jianlong Huang <jianlong.huang at starfivetech.com>
>> 
>> Add pinctrl bindings for StarFive JH7110 SoC sys pinctrl controller.
>> 
>> Signed-off-by: Jianlong Huang <jianlong.huang at starfivetech.com>
>> Co-developed-by: Emil Renner Berthing <kernel at esmil.dk>
>> Signed-off-by: Emil Renner Berthing <kernel at esmil.dk>
>> Signed-off-by: Hal Feng <hal.feng at starfivetech.com>
>> ---
>>  .../pinctrl/starfive,jh7110-sys-pinctrl.yaml  | 142 ++++++++++++++++++
>>  MAINTAINERS                                   |   3 +-
>>  .../pinctrl/starfive,jh7110-pinctrl.h         | 115 ++++++++++++++
>>  3 files changed, 259 insertions(+), 1 deletion(-)
>>  create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
>>  create mode 100644 include/dt-bindings/pinctrl/starfive,jh7110-pinctrl.h
>> 
>> diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
>> new file mode 100644
>> index 000000000000..60e616af2201
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-sys-pinctrl.yaml
>> @@ -0,0 +1,142 @@
>> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
>> +%YAML 1.2
>> +---
>> +$id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-sys-pinctrl.yaml#
>> +$schema: http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: StarFive JH7110 Sys Pin Controller
>> +
>> +description: |
>> +  Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd.
>> +
>> +  Out of the SoC's many pins only the ones named PAD_GPIO0 to PAD_GPIO63
>> +  can be multiplexed and have configurable bias, drive strength,
>> +  schmitt trigger etc.
>> +  Some peripherals have their I/O go through the 64 "GPIOs". This also
>> +  includes a number of other UARTs, I2Cs, SPIs, PWMs etc.
>> +  All these peripherals are connected to all 64 GPIOs such that
>> +  any GPIO can be set up to be controlled by any of the peripherals.
>> +
>> +maintainers:
>> +  - Jianlong Huang <jianlong.huang at starfivetech.com>
>> +
>> +properties:
>> +  compatible:
>> +    const: starfive,jh7110-sys-pinctrl
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  clocks:
>> +    maxItems: 1
>> +
>> +  resets:
>> +    maxItems: 1
>> +
>> +  interrupts:
>> +    maxItems: 1
>> +
>> +  interrupt-controller: true
>> +
>> +  '#interrupt-cells':
>> +    const: 2
>> +
>> +  gpio-controller: true
>> +
>> +  '#gpio-cells':
>> +    const: 2
>> +
>> +patternProperties:
>> +  '-[0-9]+$':
>> +    type: object
>> +    patternProperties:
>> +      '-pins$':
>> +        type: object
>> +        description: |
>> +          A pinctrl node should contain at least one subnode representing the
>> +          pinctrl groups available on the machine. Each subnode will list the
>> +          pins it needs, and how they should be configured, with regard to
>> +          muxer configuration, system signal configuration, pin groups for
>> +          vin/vout module, pin voltage, mux functions for output, mux functions
>> +          for output enable, mux functions for input.
>> +
>> +        properties:
>> +          pinmux:
>> +            description: |
>> +              The list of GPIOs and their mux settings that properties in the
>> +              node apply to. This should be set using the GPIOMUX macro.
>> +            $ref: /schemas/pinctrl/pinmux-node.yaml#/properties/pinmux
> 
> Generally, don't reference individual properties. Instead, '-pins$' 
> needs a $ref to pinmux-node.yaml.

Sorry for the late reply. '-pins$' miss a $ref to pincfg-node.yaml here. I will
add it in the next version. 'pinmux' is not a property in pincfg-node.yaml, but
a property in pinmux-node.yaml, so need a individual reference.

> 
>> +
>> +          bias-disable: true
>> +
>> +          bias-pull-up:
>> +            type: boolean
>> +
>> +          bias-pull-down:
>> +            type: boolean
>> +
>> +          drive-strength:
>> +            enum: [ 2, 4, 8, 12 ]
>> +
>> +          input-enable: true
>> +
>> +          input-disable: true
>> +
>> +          input-schmitt-enable: true
>> +
>> +          input-schmitt-disable: true
>> +
>> +          slew-rate:
>> +            maximum: 1
>> +
> 
>> +        additionalProperties: false
>> +
>> +    additionalProperties: false
> 
> It's easier to read if you put these at the beginning before a long 
> properties section.

Will fix it. Thank you for your feedback.

Best regards,
Hal

> 
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +  - clocks
>> +  - interrupts
>> +  - interrupt-controller
>> +  - '#interrupt-cells'
>> +  - gpio-controller
>> +  - '#gpio-cells'
>> +
>> +additionalProperties: false
>> +
>> +examples:
>> +  - |
>> +    gpio at 13040000 {
>> +        compatible = "starfive,jh7110-sys-pinctrl";
>> +        reg = <0x13040000 0x10000>;
>> +        clocks = <&syscrg 112>;
>> +        resets = <&syscrg 2>;
>> +        interrupts = <86>;
>> +        interrupt-controller;
>> +        #interrupt-cells = <2>;
>> +        gpio-controller;
>> +        #gpio-cells = <2>;
>> +
>> +        uart0-0 {
>> +            tx-pins {
>> +                pinmux = <0xff140005>;
>> +                bias-disable;
>> +                drive-strength = <12>;
>> +                input-disable;
>> +                input-schmitt-disable;
>> +                slew-rate = <0>;
>> +            };
>> +
>> +            rx-pins {
>> +                pinmux = <0x0E000406>;
>> +                bias-pull-up;
>> +                drive-strength = <2>;
>> +                input-enable;
>> +                input-schmitt-enable;
>> +                slew-rate = <0>;
>> +            };
>> +        };
>> +    };