[RFC PATCH 1/6] dt-bindings: pinctrl: starfive: add JH8100 pinctrl bindings
Alex Soo
yuklin.soo at starfivetech.com
Thu Dec 21 00:36:17 PST 2023
Add dt-binding documentation and header file for JH8100 pinctrl
driver.
Signed-off-by: Alex Soo <yuklin.soo at starfivetech.com>
Reviewed-by: Ley Foon Tan <leyfoon.tan at starfivetech.com>
---
.../pinctrl/starfive,jh8100-aon-pinctrl.yaml | 183 +++++++++++
.../starfive,jh8100-sys-east-pinctrl.yaml | 188 +++++++++++
.../starfive,jh8100-sys-gmac-pinctrl.yaml | 124 +++++++
.../starfive,jh8100-sys-west-pinctrl.yaml | 188 +++++++++++
.../pinctrl/starfive,jh8100-pinctrl.h | 303 ++++++++++++++++++
5 files changed, 986 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh8100-aon-pinctrl.yaml
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-east-pinctrl.yaml
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-gmac-pinctrl.yaml
create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-west-pinctrl.yaml
create mode 100644 include/dt-bindings/pinctrl/starfive,jh8100-pinctrl.h
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-aon-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-aon-pinctrl.yaml
new file mode 100644
index 000000000000..ec099a0d4c77
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-aon-pinctrl.yaml
@@ -0,0 +1,183 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jh8100-aon-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH8100 AON Pin Controller
+
+description: |
+ Pinctrl bindings for JH8100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JH8100 SoC has 4 pinctrl domains - sys_east, sys_west, sys_gmac, and aon.
+ This document provides an overview of the "aon" pinctrl domain.
+
+ The "aon" pinctrl domain contains a pin controller which provides
+ - I/O multiplexing for peripheral signals specific to this domain.
+ - function selection for GMAC0 interface modes.
+ - GPIO pins which support external GPIO interrupts or external wake-up.
+ - syscon for device reference voltage.
+
+ In the AON Pin Controller, the pins named PAD_RGPIO0 to PAD_GPIO15 can be
+ multiplexed and have configurable bias, drive strength, schmitt trigger etc.
+ Only peripherals in the AON domain can have their I/O go through the 16
+ "PAD_RGPIOs". This includes I2C, UART, watchdog, eMMC, SDIO0, XSPI etc.
+
+ All these peripherals can be connected to any of the 16 PAD_RGPIOs in such a way
+ that any iopad can be set up to be controlled by any of the peripherals.
+
+ The pin muxing is illustrated by the diagram below.
+ _____________
+ | |
+ RGPIO0 --------------| |--- PAD_RGPIO0
+ RGPIO1 --------------| AON I/O MUX |--- PAD_RGPIO1
+ ... | | ...
+ I2C8 SDA interface --| |--- PAD_RGPIO15
+ | |
+ -------------
+
+ Alternatively, the "PAD_RGPIOS" can be multiplexed to other peripherals through
+ function selection. Each iopad has a maximum of up to 3 functions - 0, 1, and 2.
+ Function 0 is the default function or peripheral signal of an iopad.
+ The function 1 and function 2 are other optional functions or peripheral signals
+ available to an iopad.
+
+ The AON Pin Controller provides regmap based syscon to configure
+
+ 1. reference voltage level of
+ - eMMC I/O interface (1.8V)
+ - SDIO0 I/O interface (3.3V, 1.8V)
+ - RGPIO bank (3.3V)
+ - Each RGPIO in the RGPIO bank share the same voltage level
+ - GMAC0 (3.3V, 2.5V, 1.8V)
+ - RMII mode, DVDD 2.5V/3.3V
+ - RGMII mode, DVDD 1.8V/2.5V
+ - XSPI (3.3V)
+
+ Voltage regulator supply the actual voltage to the device while the syscon register
+ configuration in bit [1:0] indicates the current voltage setting.
+
+ +------+------+-------------------+
+ | Bit1 | Bit0 | Reference Voltage |
+ +------+------+-------------------+
+ | 0 | 0 | 3.3 V |
+ +------+------+-------------------+
+ | 0 | 1 | 2.5 V |
+ +------+------+-------------------+
+ | 1 | x | 1.8 V |
+ +------+------+-------------------+
+
+ To increase the device voltage, set bit [1:0] to the new operating state first before
+ raising the actual voltage to the higher operating point.
+
+ To decrease the device voltage, hold bit [1:0] to the current operating state until
+ the actual voltage has stabilized at the lower operating point before changing the
+ setting.
+
+ Alternatively, a device voltage change can always be initiated by first setting syscon
+ register bit [1:0] = 0, the safe 3.3V startup condition, before changing the device
+ voltage. Then once the actual voltage is changed and has stabilized at the new operating
+ point, bit [1:0] can be reset as appropriate.
+
+maintainers:
+ - Alex Soo <yuklin.soo at starfivetech.com>
+
+properties:
+ compatible:
+ const: starfive,jh8100-aon-pinctrl
+
+ reg:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+patternProperties:
+ '-[0-9]+$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ muxer configuration, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate and drive strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ additionalProperties: false
+
+ properties:
+ pinmux:
+ description: |
+ The list of GPIOs and their mux settings or function select.
+ The GPIOMUX and PINMUX macros are used to configure the
+ I/O multiplexing and function selection respectively.
+
+ bias-disable: true
+
+ bias-pull-up:
+ type: boolean
+
+ bias-pull-down:
+ type: boolean
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ input-enable: true
+
+ input-disable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ slew-rate:
+ maximum: 1
+
+required:
+ - compatible
+ - reg
+ - resets
+ - interrupts
+ - interrupt-controller
+ - gpio-controller
+ - '#gpio-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/starfive,jh8100.h>
+ #include <dt-bindings/reset/starfive-jh8100.h>
+ #include <dt-bindings/pinctrl/starfive,jh8100-pinctrl.h>
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_aon: pinctrl at 1f300000 {
+ compatible = "starfive,jh8100-aon-pinctrl",
+ "syscon", "simple-mfd";
+ reg = <0x0 0x1f300000 0x0 0x10000>;
+ resets = <&aoncrg 0>;
+ interrupts = <160>;
+ interrupt-controller;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-east-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-east-pinctrl.yaml
new file mode 100644
index 000000000000..849fc19558af
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-east-pinctrl.yaml
@@ -0,0 +1,188 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jh8100-sys-east-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH8100 SYS_EAST Pin Controller
+
+description: |
+ Pinctrl bindings for JH8100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JH8100 SoC has 4 pinctrl domains - sys_east, sys_west, sys_gmac, and aon.
+ This document provides an overview of the "sys_east" pinctrl domain.
+
+ The "sys_east" pinctrl domain contains a pin controller which provides
+ - I/O multiplexing for peripheral signals specific to this domain.
+ - function selection for GPIO pads.
+ - GPIO interrupt handling.
+ - syscon for device voltage reference.
+
+ In the SYS_EAST Pin Controller, the pins named PAD_GPIO0_E to PAD_GPIO47_E can
+ be multiplexed and have configurable bias, drive strength, schmitt trigger etc.
+ Only peripherals in the SYS_EAST domain can have their I/O go through the 48
+ "PAD_GPIOs". This includes CANs, I2Cs, I2Ss, SPIs, UARTs, PWMs, SMBUS0, SDIO1 etc.
+
+ All these peripherals can be connected to any of the 48 PAD_GPIOs in such a way
+ that any iopad can be set up to be controlled by any of the peripherals.
+
+ The pin muxing is illustrated by the diagram below.
+ __________________
+ | |
+ GPIO0 ----------------------| |--- PAD_GPIO0_E
+ GPIO1 ----------------------| SYS_EAST I/O MUX |--- PAD_GPIO1_E
+ GPIO2 ----------------------| |--- PAD_GPIO2_E
+ ... | | ...
+ I2C0 Clock interface -------| |--- PAD_GPIO9_E
+ I2C0 Data interface -------| |--- PAD_GPIO10_E
+ ... | | ...
+ UART0 transmit interface ---| |--- PAD_GPIO20_E
+ UART0 receive interface ----| |--- PAD_GPIO21_E
+ ... | | ...
+ GPIO47 ---------------------| |--- PAD_GPIO47_E
+ | |
+ ------------------
+
+ Alternatively, the "PAD_GPIOs" can be multiplexed to other peripherals through
+ function selection. Each iopad has a maximum of up to 3 functions - 0, 1, and 2.
+ Function 0 is the default function or peripheral signal of an iopad.
+ The function 1 and function 2 are other optional functions or peripheral signals
+ available to an iopad.
+
+ The "sys_east" pinctrl domain has 4 GPIO banks - E0, E1, E2, and E3. Each GPIO bank
+ can be set to a different voltage level (3.3V or 1.8V) while GPIOs in the same bank
+ will share the same voltage level.
+
+ The SYS_EAST Pin Controller provides regmap based syscon registers to configure the
+ reference voltage level in each GPIO bank.
+
+ Voltage regulator supply the actual voltage to the GPIO bank while the syscon register
+ configuration in bit [1:0] indicates the current voltage setting.
+
+ +------+------+-------------------+
+ | Bit1 | Bit0 | Reference Voltage |
+ +------+------+-------------------+
+ | 0 | 0 | 3.3 V |
+ +------+------+-------------------+
+ | 1 | x | 1.8 V |
+ +------+------+-------------------+
+
+ To increase the device voltage, set bit [1:0] to the new operating state first before
+ raising the actual voltage to the higher operating point.
+
+ To decrease the device voltage, hold bit [1:0] to the current operating state until
+ the actual voltage has stabilized at the lower operating point before changing the
+ setting.
+
+ Alternatively, a device voltage change can always be initiated by first setting syscon
+ register bit [1:0] = 0, the safe 3.3V startup condition, before changing the device
+ voltage. Then once the actual voltage is changed and has stabilized at the new operating
+ point, bit [1:0] can be reset as appropriate.
+
+maintainers:
+ - Alex Soo <yuklin.soo at starfivetech.com>
+
+properties:
+ compatible:
+ const: starfive,jh8100-sys-pinctrl-east
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+patternProperties:
+ '-[0-9]+$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ muxer configuration, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate and drive strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ additionalProperties: false
+
+ properties:
+ pinmux:
+ description: |
+ The list of GPIOs and their mux settings or function select.
+ The GPIOMUX and PINMUX macros are used to configure the
+ I/O multiplexing and function selection respectively.
+
+ bias-disable: true
+
+ bias-pull-up:
+ type: boolean
+
+ bias-pull-down:
+ type: boolean
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ input-enable: true
+
+ input-disable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ slew-rate:
+ maximum: 1
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - resets
+ - interrupts
+ - interrupt-controller
+ - gpio-controller
+ - '#gpio-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/starfive,jh8100.h>
+ #include <dt-bindings/reset/starfive-jh8100.h>
+ #include <dt-bindings/pinctrl/starfive,jh8100-pinctrl.h>
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_east: pinctrl at 122d0000 {
+ compatible = "starfive,jh8100-sys-pinctrl-east",
+ "syscon", "simple-mfd";
+ reg = <0x0 0x122d0000 0x0 0x10000>;
+ clocks = <&syscrg_ne 153>;
+ resets = <&syscrg_ne 48>;
+ interrupts = <182>;
+ interrupt-controller;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-gmac-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-gmac-pinctrl.yaml
new file mode 100644
index 000000000000..301690456e40
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-gmac-pinctrl.yaml
@@ -0,0 +1,124 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jh8100-sys-gmac-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH8100 SYS_GMAC Pin Controller
+
+description: |
+ Pinctrl bindings for JH8100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JH8100 SoC has 4 pinctrl domains - sys_east, sys_west, sys_gmac, and aon.
+ This document provides an overview of the "sys_gmac" pinctrl domain.
+
+ The "sys_gmac" pinctrl domain contains a pin-controller which provides
+ - function selection for GMAC1 interface modes.
+ - syscon for device voltage reference.
+ - syscon for GMAC modes and slew rate control.
+
+ The SYS_GMAC Pin Controller does not have any PAD_GPIOs, therefore, it does not
+ support the GPIO pads' I/O Multiplexing and interrupt handling.
+
+ The SYS_GMAC Pin Controller provides regmap based syscon to configure
+
+ 1. reference voltage level of
+ - SDIO1 (3.3V, 1.8V)
+ - GMAC1 (3.3V, 2.5V, 1.8V)
+ - RMII mode, DVDD 2.5V/3.3V
+ - RGMII mode, DVDD 1.8V/2.5V
+
+ +------+------+-------------------+
+ | Bit1 | Bit0 | Reference Voltage |
+ +------+------+-------------------+
+ | 0 | 0 | 3.3 V |
+ +------+------+-------------------+
+ | 0 | 1 | 2.5 V |
+ +------+------+-------------------+
+ | 1 | x | 1.8 V |
+ +------+------+-------------------+
+
+ To increase the device voltage, set bit [1:0] to the new operating state first before
+ raising the actual voltage to the higher operating point.
+
+ To decrease the device voltage, hold bit [1:0] to the current operating state until
+ the actual voltage has stabilized at the lower operating point before changing the
+ setting.
+
+ Alternatively, a device voltage change can always be initiated by first setting syscon
+ register bit [1:0] = 0, the safe 3.3V startup condition, before changing the device
+ voltage. Then once the actual voltage is changed and has stabilized at the new operating
+ point, bit [1:0] can be reset as appropriate.
+
+ 2. GMAC1 interface slew rate
+
+ +------+-----------+
+ | Bit2 | Slew Rate |
+ +------+-----------+
+ | 0 | Fast |
+ +------+-----------+
+ | 1 | Slow |
+ +------+-----------+
+
+maintainers:
+ - Alex Soo <yuklin.soo at starfivetech.com>
+
+properties:
+ compatible:
+ const: starfive,jh8100-sys-pinctrl-gmac
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+patternProperties:
+ '-[0-9]+$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ muxer configuration, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate and drive strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ additionalProperties: false
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - resets
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/starfive,jh8100.h>
+ #include <dt-bindings/reset/starfive-jh8100.h>
+ #include <dt-bindings/pinctrl/starfive,jh8100-pinctrl.h>
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_gmac: pinctrl at 12770000 {
+ compatible = "starfive,jh8100-sys-pinctrl-gmac",
+ "syscon", "simple-mfd";
+ status = "disabled";
+ reg = <0x0 0x12770000 0x0 0x10000>;
+ clocks = <&gmac_sdio_crg 16>;
+ resets = <&gmac_sdio_crg 3>;
+ };
+
+ };
diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-west-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-west-pinctrl.yaml
new file mode 100644
index 000000000000..608acb76230c
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh8100-sys-west-pinctrl.yaml
@@ -0,0 +1,188 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jh8100-sys-west-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH8100 SYS_WEST Pin Controller
+
+description: |
+ Pinctrl bindings for JH8100 RISC-V SoC from StarFive Technology Ltd.
+
+ The JH8100 SoC has 4 pinctrl domains - sys_east, sys_west, sys_gmac, and aon.
+ This document provides an overview of the "sys_west" pinctrl domain.
+
+ The "sys_west" pinctrl domain contains a pin-controller which provides
+ - I/O multiplexing for peripheral signals specific to this domain.
+ - function selection for GPIO pads.
+ - GPIO interrupt handling.
+ - syscon for device voltage reference.
+
+ In the SYS_WEST Pin Controller, the pins named PAD_GPIO0_W to PAD_GPIO15_W can
+ be multiplexed and have configurable bias, drive strength, schmitt trigger etc.
+ Only peripherals in the SYS_WEST domain can have their I/O go through the 16
+ "PAD_GPIOs". This includes I2Cs, HD_AUDIO, HIFI4, SPIs, UARTs, SMBUS1 etc.
+
+ All these peripherals can be connected to any of the 16 PAD_GPIOs in such a way
+ that any iopad can be set up to be controlled by any of the peripherals.
+
+ The pin muxing is illustrated by the diagram below.
+ __________________
+ | |
+ GPIO0 ----------------------| |--- PAD_GPIO0_W
+ GPIO1 ----------------------| SYS_WEST I/O MUX |--- PAD_GPIO1_W
+ GPIO2 ----------------------| |--- PAD_GPIO2_W
+ ... | | ...
+ HIFI4 JTAG TDO interface ---| |--- PAD_GPIO10_W
+ HIFI4 JTAG TDI interface ---| |--- PAD_GPIO11_W
+ SMBUS1 Data interface -----| |--- PAD_GPIO12_W
+ SMBUS1 Clock interface -----| |--- PAD_GPIO13_W
+ ... | | ...
+ GPIO14 ---------------------| |--- PAD_GPIO14_W
+ GPIO15 ---------------------| |--- PAD_GPIO15_W
+ | |
+ ------------------
+
+ Alternatively, the "PAD_GPIOs" can be multiplexed to other peripherals through
+ function selection. Each iopad has a maximum of up to 3 functions - 0, 1, and 2.
+ Function 0 is the default function or peripheral signal of an iopad.
+ The function 1 and function 2 are other optional functions or peripheral signals
+ available to an iopad.
+
+ The "sys_west" pinctrl domain consist of 1 GPIO bank. The GPIO bank can be set to
+ a different voltage level (3.3V or 1.8V) while GPIOs in the same bank will share
+ the same voltage level.
+
+ The SYS_WEST Pin Controller provides regmap based syscon registers to configure the
+ reference voltage level in the GPIO bank.
+
+ Voltage regulator supply the actual voltage to the GPIO bank while the syscon register
+ configuration in bit [1:0] indicates the current voltage setting.
+
+ +------+------+-------------------+
+ | Bit1 | Bit0 | Reference Voltage |
+ +------+------+-------------------+
+ | 0 | 0 | 3.3 V |
+ +------+------+-------------------+
+ | 1 | x | 1.8 V |
+ +------+------+-------------------+
+
+ To increase the device voltage, set bit [1:0] to the new operating state first before
+ raising the actual voltage to the higher operating point.
+
+ To decrease the device voltage, hold bit [1:0] to the current operating state until
+ the actual voltage has stabilized at the lower operating point before changing the
+ setting.
+
+ Alternatively, a device voltage change can always be initiated by first setting syscon
+ register bit [1:0] = 0, the safe 3.3V startup condition, before changing the device
+ voltage. Then once the actual voltage is changed and has stabilized at the new operating
+ point, bit [1:0] can be reset as appropriate.
+
+maintainers:
+ - Alex Soo <yuklin.soo at starfivetech.com>
+
+properties:
+ compatible:
+ const: starfive,jh8100-sys-pinctrl-west
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 1
+
+ resets:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ interrupt-controller: true
+
+ gpio-controller: true
+
+ '#gpio-cells':
+ const: 2
+
+patternProperties:
+ '-[0-9]+$':
+ type: object
+ additionalProperties: false
+ patternProperties:
+ '-pins$':
+ type: object
+ description: |
+ A pinctrl node should contain at least one subnode representing the
+ pinctrl groups available in the domain. Each subnode will list the
+ pins it needs, and how they should be configured, with regard to
+ muxer configuration, bias, input enable/disable, input schmitt
+ trigger enable/disable, slew-rate and drive strength.
+ allOf:
+ - $ref: /schemas/pinctrl/pincfg-node.yaml
+ - $ref: /schemas/pinctrl/pinmux-node.yaml
+ additionalProperties: false
+
+ properties:
+ pinmux:
+ description: |
+ The list of GPIOs and their mux settings or function select.
+ The GPIOMUX and PINMUX macros are used to configure the
+ I/O multiplexing and function selection respectively.
+
+ bias-disable: true
+
+ bias-pull-up:
+ type: boolean
+
+ bias-pull-down:
+ type: boolean
+
+ drive-strength:
+ enum: [ 2, 4, 8, 12 ]
+
+ input-enable: true
+
+ input-disable: true
+
+ input-schmitt-enable: true
+
+ input-schmitt-disable: true
+
+ slew-rate:
+ maximum: 1
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - resets
+ - interrupts
+ - interrupt-controller
+ - gpio-controller
+ - '#gpio-cells'
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/starfive,jh8100.h>
+ #include <dt-bindings/reset/starfive-jh8100.h>
+ #include <dt-bindings/pinctrl/starfive,jh8100-pinctrl.h>
+
+ soc {
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ pinctrl_west: pinctrl at 123e0000 {
+ compatible = "starfive,jh8100-sys-pinctrl-west",
+ "syscon", "simple-mfd";
+ interrupts = <183>;
+ reg = <0x0 0x123e0000 0x0 0x10000>;
+ clocks = <&syscrg_nw 6>;
+ resets = <&syscrg_nw 1>;
+ interrupt-controller;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+ };
diff --git a/include/dt-bindings/pinctrl/starfive,jh8100-pinctrl.h b/include/dt-bindings/pinctrl/starfive,jh8100-pinctrl.h
new file mode 100644
index 000000000000..c57b7ece37a2
--- /dev/null
+++ b/include/dt-bindings/pinctrl/starfive,jh8100-pinctrl.h
@@ -0,0 +1,303 @@
+/* SPDX-License-Identifier: GPL-2.0 OR MIT */
+/*
+ * Copyright (C) 2023 StarFive Technology Co., Ltd.
+ * Author: Alex Soo <yuklin.soo at starfivetech.com>
+ *
+ */
+
+#ifndef __DT_BINDINGS_PINCTRL_STARFIVE_JH8100_H__
+#define __DT_BINDINGS_PINCTRL_STARFIVE_JH8100_H__
+
+/* sys_iomux_west pins */
+#define PAD_GPIO0_W 0
+#define PAD_GPIO1_W 1
+#define PAD_GPIO2_W 2
+#define PAD_GPIO3_W 3
+#define PAD_GPIO4_W 4
+#define PAD_GPIO5_W 5
+#define PAD_GPIO6_W 6
+#define PAD_GPIO7_W 7
+#define PAD_GPIO8_W 8
+#define PAD_GPIO9_W 9
+#define PAD_GPIO10_W 10
+#define PAD_GPIO11_W 11
+#define PAD_GPIO12_W 12
+#define PAD_GPIO13_W 13
+#define PAD_GPIO14_W 14
+#define PAD_GPIO15_W 15
+
+/* sys_iomux_west syscon */
+#define SYS_W_VREF_GPIO_W_SYSCON_REG 0x6c
+#define SYS_W_VREF_GPIO_W_SYSCON_MASK GENMASK(1, 0)
+#define SYS_W_VREF_GPIO_W_SYSCON_SHIFT 0
+#define SYS_W_VREF_ATB_ISP_VOUT_SYSCON_REG 0x70
+#define SYS_W_VREF_ATB_ISP_VOUT_SYSCON_MASK GENMASK(1, 0)
+#define SYS_W_VREF_ATB_ISP_VOUT_SYSCON_SHIFT 0
+
+/* sys_iomux_east pins */
+#define PAD_GPIO0_E 0
+#define PAD_GPIO1_E 1
+#define PAD_GPIO2_E 2
+#define PAD_GPIO3_E 3
+#define PAD_GPIO4_E 4
+#define PAD_GPIO5_E 5
+#define PAD_GPIO6_E 6
+#define PAD_GPIO7_E 7
+#define PAD_GPIO8_E 8
+#define PAD_GPIO9_E 9
+#define PAD_GPIO10_E 10
+#define PAD_GPIO11_E 11
+#define PAD_GPIO12_E 12
+#define PAD_GPIO13_E 13
+#define PAD_GPIO14_E 14
+#define PAD_GPIO15_E 15
+#define PAD_GPIO16_E 16
+#define PAD_GPIO17_E 17
+#define PAD_GPIO18_E 18
+#define PAD_GPIO19_E 19
+#define PAD_GPIO20_E 20
+#define PAD_GPIO21_E 21
+#define PAD_GPIO22_E 22
+#define PAD_GPIO23_E 23
+#define PAD_GPIO24_E 24
+#define PAD_GPIO25_E 25
+#define PAD_GPIO26_E 26
+#define PAD_GPIO27_E 27
+#define PAD_GPIO28_E 28
+#define PAD_GPIO29_E 29
+#define PAD_GPIO30_E 30
+#define PAD_GPIO31_E 31
+#define PAD_GPIO32_E 32
+#define PAD_GPIO33_E 33
+#define PAD_GPIO34_E 34
+#define PAD_GPIO35_E 35
+#define PAD_GPIO36_E 36
+#define PAD_GPIO37_E 37
+#define PAD_GPIO38_E 38
+#define PAD_GPIO39_E 39
+#define PAD_GPIO40_E 40
+#define PAD_GPIO41_E 41
+#define PAD_GPIO42_E 42
+#define PAD_GPIO43_E 43
+#define PAD_GPIO44_E 44
+#define PAD_GPIO45_E 45
+#define PAD_GPIO46_E 46
+#define PAD_GPIO47_E 47
+
+/* sys_iomux_east syscon */
+#define SYS_E_VREF_GPIO_E0_SYSCON_REG 0x0fc
+#define SYS_E_VREF_GPIO_E0_SYSCON_MASK GENMASK(1, 0)
+#define SYS_E_VREF_GPIO_E0_SYSCON_SHIFT 0
+#define SYS_E_VREF_GPIO_E1_SYSCON_REG 0x100
+#define SYS_E_VREF_GPIO_E1_SYSCON_MASK GENMASK(1, 0)
+#define SYS_E_VREF_GPIO_E1_SYSCON_SHIFT 0
+#define SYS_E_VREF_GPIO_E2_SYSCON_REG 0x104
+#define SYS_E_VREF_GPIO_E2_SYSCON_MASK GENMASK(1, 0)
+#define SYS_E_VREF_GPIO_E2_SYSCON_SHIFT 0
+#define SYS_E_VREF_GPIO_E3_SYSCON_REG 0x108
+#define SYS_E_VREF_GPIO_E3_SYSCON_MASK GENMASK(1, 0)
+#define SYS_E_VREF_GPIO_E3_SYSCON_SHIFT 0
+#define SYS_E_VREF_ATB_STG1_SYSCON_REG 0x10c
+#define SYS_E_VREF_ATB_STG1_SYSCON_MASK GENMASK(1, 0)
+#define SYS_E_VREF_ATB_STG1_SYSCON_SHIFT 0
+#define SYS_E_VREF_ATB_USB_SYSCON_REG 0x110
+#define SYS_E_VREF_ATB_USB_SYSCON_MASK GENMASK(1, 0)
+#define SYS_E_VREF_ATB_USB_SYSCON_SHIFT 0
+
+/* sys_iomux_gmac pins */
+#define PAD_GMAC1_MDC 0
+#define PAD_GMAC1_MDIO 1
+#define PAD_GMAC1_RXD0 2
+#define PAD_GMAC1_RXD1 3
+#define PAD_GMAC1_RXD2 4
+#define PAD_GMAC1_RXD3 5
+#define PAD_GMAC1_RXDV 6
+#define PAD_GMAC1_RXC 7
+#define PAD_GMAC1_TXD0 8
+#define PAD_GMAC1_TXD1 9
+#define PAD_GMAC1_TXD2 10
+#define PAD_GMAC1_TXD3 11
+#define PAD_GMAC1_TXEN 12
+#define PAD_GMAC1_TXC 13
+
+/* sys_iomux_gmac vref syscon registers */
+#define SYS_G_VREF_GMAC1_SYSCON_REG 0x08
+#define SYS_G_VREF_GMAC1_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_VREF_GMAC1_SYSCON_SHIFT 0
+#define SYS_G_VREF_SDIO1_SYSCON_REG 0x0c
+#define SYS_G_VREF_SDIO1_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_VREF_SDIO1_SYSCON_SHIFT 0
+
+/* sys_iomux_gmac interface (rmii/rgmii) syscon registers */
+#define SYS_G_GMAC1_MDC_SYSCON_REG 0x10
+#define SYS_G_GMAC1_MDC_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_MDC_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_MDIO_SYSCON_REG 0x14
+#define SYS_G_GMAC1_MDIO_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_MDIO_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_RXD0_SYSCON_REG 0x18
+#define SYS_G_GMAC1_RXD0_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_RXD0_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_RXD1_SYSCON_REG 0x1c
+#define SYS_G_GMAC1_RXD1_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_RXD1_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_RXD2_SYSCON_REG 0x20
+#define SYS_G_GMAC1_RXD2_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_RXD2_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_RXD3_SYSCON_REG 0x24
+#define SYS_G_GMAC1_RXD3_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_RXD3_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_RXDV_SYSCON_REG 0x28
+#define SYS_G_GMAC1_RXDV_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_RXDV_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_RXC_SYSCON_REG 0x2c
+#define SYS_G_GMAC1_RXC_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_RXC_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_TXD0_SYSCON_REG 0x30
+#define SYS_G_GMAC1_TXD0_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_TXD0_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_TXD1_SYSCON_REG 0x34
+#define SYS_G_GMAC1_TXD1_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_TXD1_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_TXD2_SYSCON_REG 0x38
+#define SYS_G_GMAC1_TXD2_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_TXD2_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_TXD3_SYSCON_REG 0x3c
+#define SYS_G_GMAC1_TXD3_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_TXD3_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_TXEN_SYSCON_REG 0x40
+#define SYS_G_GMAC1_TXEN_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_TXEN_SYSCON_SHIFT 0
+#define SYS_G_GMAC1_TXC_SYSCON_REG 0x44
+#define SYS_G_GMAC1_TXC_SYSCON_MASK GENMASK(1, 0)
+#define SYS_G_GMAC1_TXC_SYSCON_SHIFT 0
+
+/* sys_iomux_gmac timing (slew rate) registers */
+#define SYS_G_GMAC1_MDC_SLEW_REG 0x10
+#define SYS_G_GMAC1_MDC_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_MDC_SLEW_SHIFT 2
+#define SYS_G_GMAC1_MDIO_SLEW_REG 0x14
+#define SYS_G_GMAC1_MDIO_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_MDIO_SLEW_SHIFT 2
+#define SYS_G_GMAC1_RXD0_SLEW_REG 0x18
+#define SYS_G_GMAC1_RXD0_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_RXD0_SLEW_SHIFT 2
+#define SYS_G_GMAC1_RXD1_SLEW_REG 0x1c
+#define SYS_G_GMAC1_RXD1_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_RXD1_SLEW_SHIFT 2
+#define SYS_G_GMAC1_RXD2_SLEW_REG 0x20
+#define SYS_G_GMAC1_RXD2_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_RXD2_SLEW_SHIFT 2
+#define SYS_G_GMAC1_RXD3_SLEW_REG 0x24
+#define SYS_G_GMAC1_RXD3_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_RXD3_SLEW_SHIFT 2
+#define SYS_G_GMAC1_RXDV_SLEW_REG 0x28
+#define SYS_G_GMAC1_RXDV_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_RXDV_SLEW_SHIFT 2
+#define SYS_G_GMAC1_RXC_SLEW_REG 0x2c
+#define SYS_G_GMAC1_RXC_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_RXC_SLEW_SHIFT 2
+#define SYS_G_GMAC1_TXD0_SLEW_REG 0x30
+#define SYS_G_GMAC1_TXD0_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_TXD0_SLEW_SHIFT 2
+#define SYS_G_GMAC1_TXD1_SLEW_REG 0x34
+#define SYS_G_GMAC1_TXD1_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_TXD1_SLEW_SHIFT 2
+#define SYS_G_GMAC1_TXD2_SLEW_REG 0x38
+#define SYS_G_GMAC1_TXD2_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_TXD2_SLEW_SHIFT 2
+#define SYS_G_GMAC1_TXD3_SLEW_REG 0x3c
+#define SYS_G_GMAC1_TXD3_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_TXD3_SLEW_SHIFT 2
+#define SYS_G_GMAC1_TXEN_SLEW_REG 0x40
+#define SYS_G_GMAC1_TXEN_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_TXEN_SLEW_SHIFT 2
+#define SYS_G_GMAC1_TXC_SLEW_REG 0x44
+#define SYS_G_GMAC1_TXC_SLEW_MASK BIT(2)
+#define SYS_G_GMAC1_TXC_SLEW_SHIFT 2
+
+/* aon_iomux pins */
+#define PAD_RGPIO0 0
+#define PAD_RGPIO1 1
+#define PAD_RGPIO2 2
+#define PAD_RGPIO3 3
+#define PAD_RGPIO4 4
+#define PAD_RGPIO5 5
+#define PAD_RGPIO6 6
+#define PAD_RGPIO7 7
+#define PAD_RGPIO8 8
+#define PAD_RGPIO9 9
+#define PAD_RGPIO10 10
+#define PAD_RGPIO11 11
+#define PAD_RGPIO12 12
+#define PAD_RGPIO13 13
+#define PAD_RGPIO14 14
+#define PAD_RGPIO15 15
+#define PAD_TESTEN 16
+#define PAD_RSTN 17
+#define PAD_OSCK_XIN 18
+#define PAD_OSCK_XOUT 19
+#define PAD_OSCM_XIN 20
+#define PAD_OSCM_XOUT 21
+#define PAD_GMAC0_MDC 22
+#define PAD_GMAC0_MDIO 23
+#define PAD_GMAC0_RXD0 24
+#define PAD_GMAC0_RXD1 25
+#define PAD_GMAC0_RXD2 26
+#define PAD_GMAC0_RXD3 27
+#define PAD_GMAC0_RXDV 28
+#define PAD_GMAC0_RXC 29
+#define PAD_GMAC0_TXD0 30
+#define PAD_GMAC0_TXD1 31
+#define PAD_GMAC0_TXD2 32
+#define PAD_GMAC0_TXD3 33
+#define PAD_GMAC0_TXEN 34
+#define PAD_GMAC0_TXC 35
+
+/* aon_iomux vref syscon registers */
+#define AON_VREF_RGPIO_SYSCON_REG 0x58
+#define AON_VREF_RGPIO_SYSCON_MASK GENMASK(1, 0)
+#define AON_VREF_RGPIO_SYSCON_SHIFT 0
+#define AON_VREF_GMAC_SYSCON_REG 0X5c
+#define AON_VREF_GMAC_SYSCON_MASK GENMASK(1, 0)
+#define AON_VREF_GMAC_SYSCON_SHIFT 0
+#define AON_VREF_XSPI_SYSCON_REG 0x60
+#define AON_VREF_XSPI_SYSCON_MASK GENMASK(1, 0)
+#define AON_VREF_XSPI_SYSCON_SHIFT 0
+#define AON_VREF_EMMC_U0_SYSCON_REG 0x64
+#define AON_VREF_EMMC_U0_SYSCON_MASK GENMASK(1, 0)
+#define AON_VREF_EMMC_U0_SYSCON_SHIFT 0
+#define AON_VREF_EMMC_U1_SYSCON_REG 0x68
+#define AON_VREF_EMMC_U1_SYSCON_MASK GENMASK(1, 0)
+#define AON_VREF_EMMC_U1_SYSCON_SHIFT 0
+#define AON_VREF_EMMC_U2_SYSCON_REG 0x6c
+#define AON_VREF_EMMC_U2_SYSCON_MASK GENMASK(1, 0)
+#define AON_VREF_EMMC_U2_SYSCON_SHIFT 0
+#define AON_VREF_SDIO_U0_SYSCON_REG 0x70
+#define AON_VREF_SDIO_U0_SYSCON_MASK GENMASK(1, 0)
+#define AON_VREF_SDIO_U0_SYSCON_SHIFT 0
+#define AON_VREF_SDIO_U1_SYSCON_REG 0x74
+#define AON_VREF_SDIO_U1_SYSCON_MASK GENMASK(1, 0)
+#define AON_VREF_SDIO_U1_SYSCON_SHIFT 0
+
+#define GPOUT_LOW 0
+#define GPOUT_HIGH 1
+
+#define GPOEN_ENABLE 0
+#define GPOEN_DISABLE 1
+
+#define GPI_NONE 255
+
+/* vref syscon value */
+#define PAD_VREF_SYSCON_IO_3V3 0
+#define PAD_VREF_SYSCON_IO_1V8 2
+
+/* gmac interface (rmii/rgmii) syscon value */
+#define GMAC_RMII_MODE 0 /* RMII mode, DVDD 2.5V/3.3V */
+#define GMAC_RGMII_MODE 1 /* RGMII mode, DVDD 1.8V/2.5V */
+
+/* gmac timing syscon value */
+#define GMAC_SLEW_RATE_FAST 0
+#define GMAC_SLEW_RATE_SLOW 1
+
+#endif
--
2.25.1
More information about the linux-riscv
mailing list