[PATCH v5 3/4] riscv: dts: starfive: visionfive-v1: Setup ethernet phy

[Emil Renner Berthing]

Cristian Ciocaltea wrote:
> The StarFive VisionFive V1 SBC uses a Motorcomm YT8521 PHY supporting
> RGMII-ID, but requires manual adjustment of the RX internal delay to
> work properly.
>
> The default RX delay provided by the driver is 1.95 ns, which proves to
> be too high. Applying a 50% reduction seems to mitigate the issue.
>
> Also note this adjustment is not necessary on BeagleV Starlight SBC,
> which uses a Microchip PHY.  Hence, there is no indication of a
> misbehaviour on the GMAC side, but most likely the issue stems from
> the Motorcomm PHY.
>
> While at it, drop the redundant gpio include, which is already provided
> by jh7100-common.dtsi.
>
> Co-developed-by: Emil Renner Berthing <emil.renner.berthing at canonical.com>
> Signed-off-by: Emil Renner Berthing <emil.renner.berthing at canonical.com>
> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea at collabora.com>
> Reviewed-by: Jacob Keller <jacob.e.keller at intel.com>
> Reviewed-by: Andrew Lunn <andrew at lunn.ch>
> ---
>  .../jh7100-starfive-visionfive-v1.dts         | 22 ++++++++++++++++++-
>  1 file changed, 21 insertions(+), 1 deletion(-)
>
> diff --git a/arch/riscv/boot/dts/starfive/jh7100-starfive-visionfive-v1.dts b/arch/riscv/boot/dts/starfive/jh7100-starfive-visionfive-v1.dts
> index e82af72f1aaf..4e396f820660 100644
> --- a/arch/riscv/boot/dts/starfive/jh7100-starfive-visionfive-v1.dts
> +++ b/arch/riscv/boot/dts/starfive/jh7100-starfive-visionfive-v1.dts
> @@ -6,7 +6,6 @@
>
>  /dts-v1/;
>  #include "jh7100-common.dtsi"
> -#include <dt-bindings/gpio/gpio.h>
>
>  / {
>  	model = "StarFive VisionFive V1";
> @@ -18,3 +17,24 @@ gpio-restart {
>  		priority = <224>;
>  	};
>  };
> +
> +/*
> + * The board uses a Motorcomm YT8521 PHY supporting RGMII-ID, but requires
> + * manual adjustment of the RX internal delay to work properly.  The default
> + * RX delay provided by the driver (1.95ns) is too high, but applying a 50%
> + * reduction seems to mitigate the issue.
> + *
> + * It is worth noting the adjustment is not necessary on BeagleV Starlight SBC,
> + * which uses a Microchip PHY.  Hence, most likely the Motorcomm PHY is the one
> + * responsible for the misbehaviour, not the GMAC.
> + */
> +&mdio {
> +	phy: ethernet-phy at 0 {
> +		reg = <0>;
> +		rx-internal-delay-ps = <900>;
> +	};
> +};
> +
> +&gmac {
> +	phy-handle = <&phy>;
> +};

Alphabetical ordering here, please.

/Emil