[PATCH bpf-next v3 0/3] bpf, riscv: use BPF prog pack allocator in BPF JIT
Palmer Dabbelt
palmer at dabbelt.com
Wed Aug 30 13:43:40 PDT 2023
On Wed, 30 Aug 2023 06:59:13 PDT (-0700), bjorn at kernel.org wrote:
> Daniel Borkmann <daniel at iogearbox.net> writes:
>
>> On 8/29/23 12:06 PM, Björn Töpel wrote:
>>> Puranjay Mohan <puranjay12 at gmail.com> writes:
>>>
>>>> Changes in v2 -> v3:
>>>> 1. Fix maximum width of code in patches from 80 to 100. [All patches]
>>>> 2. Add checks for ctx->ro_insns == NULL. [Patch 3]
>>>> 3. Fix check for edge condition where amount of text to set > 2 * pagesize
>>>> [Patch 1 and 2]
>>>> 4. Add reviewed-by in patches.
>>>> 5. Adding results of selftest here:
>>>> Using the command: ./test_progs on qemu
>>>> Without the series: Summary: 336/3162 PASSED, 56 SKIPPED, 90 FAILED
>>>> With this series: Summary: 336/3162 PASSED, 56 SKIPPED, 90 FAILED
>>>>
>>>> Changes in v1 -> v2:
>>>> 1. Implement a new function patch_text_set_nosync() to be used in bpf_arch_text_invalidate().
>>>> The implementation in v1 called patch_text_nosync() in a loop and it was bad as it would
>>>> call flush_icache_range() for every word making it really slow. This was found by running
>>>> the test_tag selftest which would take forever to complete.
>>>>
>>>> Here is some data to prove the V2 fixes the problem:
>>>>
>>>> Without this series:
>>>> root at rv-selftester:~/src/kselftest/bpf# time ./test_tag
>>>> test_tag: OK (40945 tests)
>>>>
>>>> real 7m47.562s
>>>> user 0m24.145s
>>>> sys 6m37.064s
>>>>
>>>> With this series applied:
>>>> root at rv-selftester:~/src/selftest/bpf# time ./test_tag
>>>> test_tag: OK (40945 tests)
>>>>
>>>> real 7m29.472s
>>>> user 0m25.865s
>>>> sys 6m18.401s
>>>>
>>>> BPF programs currently consume a page each on RISCV. For systems with many BPF
>>>> programs, this adds significant pressure to instruction TLB. High iTLB pressure
>>>> usually causes slow down for the whole system.
>>>>
>>>> Song Liu introduced the BPF prog pack allocator[1] to mitigate the above issue.
>>>> It packs multiple BPF programs into a single huge page. It is currently only
>>>> enabled for the x86_64 BPF JIT.
>>>>
>>>> I enabled this allocator on the ARM64 BPF JIT[2]. It is being reviewed now.
>>>>
>>>> This patch series enables the BPF prog pack allocator for the RISCV BPF JIT.
>>>> This series needs a patch[3] from the ARM64 series to work.
>>>>
>>>> ======================================================
>>>> Performance Analysis of prog pack allocator on RISCV64
>>>> ======================================================
>>>>
>>>> Test setup:
>>>> ===========
>>>>
>>>> Host machine: Debian GNU/Linux 11 (bullseye)
>>>> Qemu Version: QEMU emulator version 8.0.3 (Debian 1:8.0.3+dfsg-1)
>>>> u-boot-qemu Version: 2023.07+dfsg-1
>>>> opensbi Version: 1.3-1
>>>>
>>>> To test the performance of the BPF prog pack allocator on RV, a stresser
>>>> tool[4] linked below was built. This tool loads 8 BPF programs on the system and
>>>> triggers 5 of them in an infinite loop by doing system calls.
>>>>
>>>> The runner script starts 20 instances of the above which loads 8*20=160 BPF
>>>> programs on the system, 5*20=100 of which are being constantly triggered.
>>>> The script is passed a command which would be run in the above environment.
>>>>
>>>> The script was run with following perf command:
>>>> ./run.sh "perf stat -a \
>>>> -e iTLB-load-misses \
>>>> -e dTLB-load-misses \
>>>> -e dTLB-store-misses \
>>>> -e instructions \
>>>> --timeout 60000"
>>>>
>>>> The output of the above command is discussed below before and after enabling the
>>>> BPF prog pack allocator.
>>>>
>>>> The tests were run on qemu-system-riscv64 with 8 cpus, 16G memory. The rootfs
>>>> was created using Bjorn's riscv-cross-builder[5] docker container linked below.
>>>>
>>>> Results
>>>> =======
>>>>
>>>> Before enabling prog pack allocator:
>>>> ------------------------------------
>>>>
>>>> Performance counter stats for 'system wide':
>>>>
>>>> 4939048 iTLB-load-misses
>>>> 5468689 dTLB-load-misses
>>>> 465234 dTLB-store-misses
>>>> 1441082097998 instructions
>>>>
>>>> 60.045791200 seconds time elapsed
>>>>
>>>> After enabling prog pack allocator:
>>>> -----------------------------------
>>>>
>>>> Performance counter stats for 'system wide':
>>>>
>>>> 3430035 iTLB-load-misses
>>>> 5008745 dTLB-load-misses
>>>> 409944 dTLB-store-misses
>>>> 1441535637988 instructions
>>>>
>>>> 60.046296600 seconds time elapsed
>>>>
>>>> Improvements in metrics
>>>> =======================
>>>>
>>>> It was expected that the iTLB-load-misses would decrease as now a single huge
>>>> page is used to keep all the BPF programs compared to a single page for each
>>>> program earlier.
>>>>
>>>> --------------------------------------------
>>>> The improvement in iTLB-load-misses: -30.5 %
>>>> --------------------------------------------
>>>>
>>>> I repeated this expriment more than 100 times in different setups and the
>>>> improvement was always greater than 30%.
>>>>
>>>> This patch series is boot tested on the Starfive VisionFive 2 board[6].
>>>> The performance analysis was not done on the board because it doesn't
>>>> expose iTLB-load-misses, etc. The stresser program was run on the board to test
>>>> the loading and unloading of BPF programs
>>>>
>>>> [1] https://lore.kernel.org/bpf/20220204185742.271030-1-song@kernel.org/
>>>> [2] https://lore.kernel.org/all/20230626085811.3192402-1-puranjay12@gmail.com/
>>>> [3] https://lore.kernel.org/all/20230626085811.3192402-2-puranjay12@gmail.com/
>>>> [4] https://github.com/puranjaymohan/BPF-Allocator-Bench
>>>> [5] https://github.com/bjoto/riscv-cross-builder
>>>> [6] https://www.starfivetech.com/en/site/boards
>>>>
>>>> Puranjay Mohan (3):
>>>> riscv: extend patch_text_nosync() for multiple pages
>>>> riscv: implement a memset like function for text
>>>> bpf, riscv: use prog pack allocator in the BPF JIT
>>>
>>> Thank you! For the series:
>>>
>>> Acked-by: Björn Töpel <bjorn at kernel.org>
>>> Tested-by: Björn Töpel <bjorn at rivosinc.com>
>>>
>>> @Alexei @Daniel This series depends on a core BPF patch from the Arm
>>> series [3].
>
> [snip]
>> If not yet, perhaps you could ship this series along with your PR to Linus
>> during this merge window given the big net PR (incl. bpf) was already merged
>> yesterday. So from our side only fixes ship to Linus.
>
> Are you OK with this patch going thru the riscv tree as well?
I'm generally fine taking almost anything, as long as whomever usually
takes them acks it.
More information about the linux-riscv
mailing list