[RFC v4 4/4] riscv: dts: starfive: jh7100: Add PWM node and pins configuration

[Emil Renner Berthing]

On Fri, 25 Aug 2023 at 10:16, William Qiu <william.qiu at starfivetech.com> wrote:
> Add StarFive JH7100 PWM controller node and add PWM pins configuration
> on VisionFive 2 board.

Hi William,

This is the VisionFive V1 board right?

/Emil

> Signed-off-by: William Qiu <william.qiu at starfivetech.com>
> ---
>  .../boot/dts/starfive/jh7100-common.dtsi      | 24 +++++++++++++++++++
>  arch/riscv/boot/dts/starfive/jh7100.dtsi      |  9 +++++++
>  2 files changed, 33 insertions(+)
>
> diff --git a/arch/riscv/boot/dts/starfive/jh7100-common.dtsi b/arch/riscv/boot/dts/starfive/jh7100-common.dtsi
> index b93ce351a90f..746867b882b0 100644
> --- a/arch/riscv/boot/dts/starfive/jh7100-common.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7100-common.dtsi
> @@ -84,6 +84,24 @@ GPO_I2C2_PAD_SDA_OEN,
>                 };
>         };
>
> +       pwm_pins: pwm-0 {
> +               pwm-pins {
> +                       pinmux = <GPIOMUX(7,
> +                                 GPO_PWM_PAD_OUT_BIT0,
> +                                 GPO_PWM_PAD_OE_N_BIT0,
> +                                 GPI_NONE)>,
> +                                <GPIOMUX(5,
> +                                 GPO_PWM_PAD_OUT_BIT1,
> +                                 GPO_PWM_PAD_OE_N_BIT1,
> +                                 GPI_NONE)>;
> +                       bias-disable;
> +                       drive-strength = <35>;
> +                       input-disable;
> +                       input-schmitt-disable;
> +                       slew-rate = <0>;
> +               };
> +       };
> +
>         uart3_pins: uart3-0 {
>                 rx-pins {
>                         pinmux = <GPIOMUX(13, GPO_LOW, GPO_DISABLE,
> @@ -154,6 +172,12 @@ &osc_aud {
>         clock-frequency = <27000000>;
>  };
>
> +&ptc {
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&pwm_pins>;
> +       status = "okay";
> +};
> +
>  &uart3 {
>         pinctrl-names = "default";
>         pinctrl-0 = <&uart3_pins>;
> diff --git a/arch/riscv/boot/dts/starfive/jh7100.dtsi b/arch/riscv/boot/dts/starfive/jh7100.dtsi
> index 4218621ea3b9..7f5bb19e636e 100644
> --- a/arch/riscv/boot/dts/starfive/jh7100.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7100.dtsi
> @@ -248,5 +248,14 @@ watchdog at 12480000 {
>                         resets = <&rstgen JH7100_RSTN_WDTIMER_APB>,
>                                  <&rstgen JH7100_RSTN_WDT>;
>                 };
> +
> +               ptc: pwm at 12490000 {
> +                       compatible = "starfive,jh7100-pwm";
> +                       reg = <0x0 0x12490000 0x0 0x10000>;
> +                       clocks = <&clkgen JH7100_CLK_PWM_APB>;
> +                       resets = <&rstgen JH7100_RSTN_PWM_APB>;
> +                       #pwm-cells = <3>;
> +                       status = "disabled";
> +               };
>         };
>  };
> --
> 2.34.1
>
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv