[-next v1] riscv: dts: starfive: visionfive 2: Enable usb0 and fix tdm pins sort order

[Krzysztof Kozlowski]

On 28/08/2023 13:52, Hal Feng wrote:
> usb0 was disabled by mistake when merging, so enable it.
> tdm_pins node should be sorted alphabetically.
> 
> Fixes: e7c304c0346d ("riscv: dts: starfive: jh7110: add the node and pins configuration for tdm")
> Signed-off-by: Hal Feng <hal.feng at starfivetech.com>
> ---
>  .../jh7110-starfive-visionfive-2.dtsi         | 49 ++++++++++---------
>  1 file changed, 25 insertions(+), 24 deletions(-)
> 
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> index d79f94432b27..382dfb5e64e4 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> @@ -440,30 +440,6 @@ GPOEN_ENABLE,
>  		};
>  	};
>  
> -	uart0_pins: uart0-0 {
> -		tx-pins {
> -			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
> -					     GPOEN_ENABLE,
> -					     GPI_NONE)>;
> -			bias-disable;
> -			drive-strength = <12>;
> -			input-disable;
> -			input-schmitt-disable;
> -			slew-rate = <0>;
> -		};
> -
> -		rx-pins {
> -			pinmux = <GPIOMUX(6, GPOUT_LOW,
> -					     GPOEN_DISABLE,
> -					     GPI_SYS_UART0_RX)>;
> -			bias-disable; /* external pull-up */
> -			drive-strength = <2>;
> -			input-enable;
> -			input-schmitt-enable;
> -			slew-rate = <0>;
> -		};
> -	};
> -
>  	tdm_pins: tdm-0 {
>  		tx-pins {
>  			pinmux = <GPIOMUX(44, GPOUT_SYS_TDM_TXD,
> @@ -497,6 +473,30 @@ GPOEN_DISABLE,
>  			input-enable;
>  		};
>  	};
> +
> +	uart0_pins: uart0-0 {
> +		tx-pins {
> +			pinmux = <GPIOMUX(5, GPOUT_SYS_UART0_TX,
> +					     GPOEN_ENABLE,
> +					     GPI_NONE)>;
> +			bias-disable;
> +			drive-strength = <12>;
> +			input-disable;
> +			input-schmitt-disable;
> +			slew-rate = <0>;
> +		};
> +
> +		rx-pins {
> +			pinmux = <GPIOMUX(6, GPOUT_LOW,
> +					     GPOEN_DISABLE,
> +					     GPI_SYS_UART0_RX)>;
> +			bias-disable; /* external pull-up */
> +			drive-strength = <2>;
> +			input-enable;
> +			input-schmitt-enable;
> +			slew-rate = <0>;
> +		};


What is fixed in this hunk? Order of nodes is just a style, not a bug
needing backports.

Best regards,
Krzysztof