[PATCH v4 3/4] riscv: dts: starfive: Add mmc node
Emil Renner Berthing
emil.renner.berthing at canonical.com
Sat Aug 5 06:14:20 PDT 2023
On Wed, 15 Feb 2023 at 13:26, William Qiu <william.qiu at starfivetech.com> wrote:
> On 2023/2/15 20:22, Emil Renner Berthing wrote:
> > On Wed, 15 Feb 2023 at 13:12, Emil Renner Berthing
> > <emil.renner.berthing at canonical.com> wrote:
> >>
> >> On Wed, 15 Feb 2023 at 12:35, William Qiu <william.qiu at starfivetech.com> wrote:
> >> >
> >> > Add the mmc node for the StarFive JH7110 SoC.
> >> > Set mmco node to emmc and set mmc1 node to sd.
> >> >
> >> > Signed-off-by: William Qiu <william.qiu at starfivetech.com>
> >> > ---
> >> > .../jh7110-starfive-visionfive-2.dtsi | 23 +++++++++
> >> > arch/riscv/boot/dts/starfive/jh7110.dtsi | 47 +++++++++++++++++++
> >> > 2 files changed, 70 insertions(+)
> >> >
> >> > diff --git a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> >> > index c60280b89c73..e1a0248e907f 100644
> >> > --- a/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> >> > +++ b/arch/riscv/boot/dts/starfive/jh7110-starfive-visionfive-2.dtsi
> >> > @@ -42,6 +42,29 @@ &rtc_osc {
> >> > clock-frequency = <32768>;
> >> > };
> >> >
> >> > +&mmc0 {
> >> > + max-frequency = <100000000>;
> >> > + bus-width = <8>;
> >> > + cap-mmc-highspeed;
> >> > + mmc-ddr-1_8v;
> >> > + mmc-hs200-1_8v;
> >> > + non-removable;
> >> > + cap-mmc-hw-reset;
> >> > + post-power-on-delay-ms = <200>;
> >> > + status = "okay";
> >> > +};
> >> > +
> >> > +&mmc1 {
> >> > + max-frequency = <100000000>;
> >> > + bus-width = <4>;
> >> > + no-sdio;
> >> > + no-mmc;
> >> > + broken-cd;
> >> > + cap-sd-highspeed;
> >> > + post-power-on-delay-ms = <200>;
> >> > + status = "okay";
> >> > +};
> >
> > These nodes are also still oddly placed in the middle of the external
> > clocks. Again please keep the external clocks at the top and then
> > order the nodes alphabetically to have some sort of system.
> >
>
>
> Hi Emil,
>
> I'll update it in next version.
Hi William,
It seems the mmc nodes are still missing from the upstream device
tree. The sysreg nodes have been added in Conors riscv-dt-for-next[1]
branch, so I don't see any missing dependencies. Could you please
update and send a new version of this?
[1]: https://git.kernel.org/pub/scm/linux/kernel/git/conor/linux.git/log/?h=riscv-dt-for-next
/Emil
> Best Regards
> William
>
> >> > &gmac0_rmii_refin {
> >> > clock-frequency = <50000000>;
> >> > };
> >> > diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> >> > index 64d260ea1f29..17f7b3ee6ca3 100644
> >> > --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> >> > +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> >> > @@ -314,6 +314,11 @@ uart2: serial at 10020000 {
> >> > status = "disabled";
> >> > };
> >> >
> >> > + stg_syscon: syscon at 10240000 {
> >> > + compatible = "starfive,jh7110-stg-syscon", "syscon";
> >> > + reg = <0x0 0x10240000 0x0 0x1000>;
> >> > + };
> >> > +
> >> > uart3: serial at 12000000 {
> >> > compatible = "snps,dw-apb-uart";
> >> > reg = <0x0 0x12000000 0x0 0x10000>;
> >> > @@ -370,6 +375,11 @@ syscrg: clock-controller at 13020000 {
> >> > #reset-cells = <1>;
> >> > };
> >> >
> >> > + sys_syscon: syscon at 13030000 {
> >> > + compatible = "starfive,jh7110-sys-syscon", "syscon";
> >> > + reg = <0x0 0x13030000 0x0 0x1000>;
> >> > + };
> >> > +
> >> > gpio: gpio at 13040000 {
> >> > compatible = "starfive,jh7110-sys-pinctrl";
> >> > reg = <0x0 0x13040000 0x0 0x10000>;
> >> > @@ -397,6 +407,11 @@ aoncrg: clock-controller at 17000000 {
> >> > #reset-cells = <1>;
> >> > };
> >> >
> >> > + aon_syscon: syscon at 17010000 {
> >> > + compatible = "starfive,jh7110-aon-syscon", "syscon";
> >> > + reg = <0x0 0x17010000 0x0 0x1000>;
> >> > + };
> >> > +
> >> > gpioa: gpio at 17020000 {
> >> > compatible = "starfive,jh7110-aon-pinctrl";
> >> > reg = <0x0 0x17020000 0x0 0x10000>;
> >> > @@ -407,5 +422,37 @@ gpioa: gpio at 17020000 {
> >> > gpio-controller;
> >> > #gpio-cells = <2>;
> >> > };
> >> > +
> >> > + mmc0: mmc at 16010000 {
> >> > + compatible = "starfive,jh7110-mmc";
> >> > + reg = <0x0 0x16010000 0x0 0x10000>;
> >> > + clocks = <&syscrg JH7110_SYSCLK_SDIO0_AHB>,
> >> > + <&syscrg JH7110_SYSCLK_SDIO0_SDCARD>;
> >> > + clock-names = "biu","ciu";
> >> > + resets = <&syscrg JH7110_SYSRST_SDIO0_AHB>;
> >> > + reset-names = "reset";
> >> > + interrupts = <74>;
> >> > + fifo-depth = <32>;
> >> > + fifo-watermark-aligned;
> >> > + data-addr = <0>;
> >> > + starfive,sysreg = <&sys_syscon 0x14 0x1a 0x7c000000>;
> >> > + status = "disabled";
> >> > + };
> >> > +
> >> > + mmc1: mmc at 16020000 {
> >> > + compatible = "starfive,jh7110-mmc";
> >> > + reg = <0x0 0x16020000 0x0 0x10000>;
> >> > + clocks = <&syscrg JH7110_SYSCLK_SDIO1_AHB>,
> >> > + <&syscrg JH7110_SYSCLK_SDIO1_SDCARD>;
> >> > + clock-names = "biu","ciu";
> >> > + resets = <&syscrg JH7110_SYSRST_SDIO1_AHB>;
> >> > + reset-names = "reset";
> >> > + interrupts = <75>;
> >> > + fifo-depth = <32>;
> >> > + fifo-watermark-aligned;
> >> > + data-addr = <0>;
> >> > + starfive,sysreg = <&sys_syscon 0x9c 0x1 0x3e>;
> >> > + status = "disabled";
> >> > + };
> >>
> >> Hi William,
> >>
> >> These nodes still don't seem to be sorted by address, eg. by the
> >> number after the @
> >> Also please move the dt-binding patch before this one, so dtb_check
> >> won't fail no matter where git bisect happens to land.
> >>
> >> /Emil
> >>
> >> > };
> >> > };
> >> > --
> >> > 2.34.1
> >> >
> >> >
> >> > _______________________________________________
> >> > linux-riscv mailing list
> >> > linux-riscv at lists.infradead.org
> >> > http://lists.infradead.org/mailman/listinfo/linux-riscv
More information about the linux-riscv
mailing list