[PATCH v2 05/10] ARM: dts: sunxi: h3/h5: Switch dma-names order for snps,dw-apb-uart nodes

Jernej Škrabec jernej.skrabec at gmail.com
Sat Apr 8 05:13:14 PDT 2023


Dne torek, 21. marec 2023 ob 22:56:19 CEST je Cristian Ciocaltea napisal(a):
> Commit 370f696e4474 ("dt-bindings: serial: snps-dw-apb-uart: add dma &
> dma-names properties") documented dma-names property to handle Allwinner
> D1 dtbs_check warnings, but relies on the rx->tx ordering, which is the
> reverse of what a bunch of different boards expect.
> 
> The initial proposed solution was to allow a flexible dma-names order in
> the binding, due to potential ABI breakage concerns after fixing the DTS
> files. But luckily the Allwinner boards are not affected, since they are
> using a shared DMA channel for rx and tx.
> 
> Hence, the first step in fixing the inconsistency was to change
> dma-names order in the binding to tx->rx.
> 
> Do the same for the snps,dw-apb-uart nodes in the DTS file.
> 
> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea at collabora.com>

Acked-by: Jernej Skrabec <jernej.skrabec at gmail.com>

Best regards,
Jernej

> ---
>  arch/arm/boot/dts/sunxi-h3-h5.dtsi | 8 ++++----
>  1 file changed, 4 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> b/arch/arm/boot/dts/sunxi-h3-h5.dtsi index 686193bd6bd9..ade1cd50e445
> 100644
> --- a/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> +++ b/arch/arm/boot/dts/sunxi-h3-h5.dtsi
> @@ -710,7 +710,7 @@ uart0: serial at 1c28000 {
>  			clocks = <&ccu CLK_BUS_UART0>;
>  			resets = <&ccu RST_BUS_UART0>;
>  			dmas = <&dma 6>, <&dma 6>;
> -			dma-names = "rx", "tx";
> +			dma-names = "tx", "rx";
>  			status = "disabled";
>  		};
> 
> @@ -723,7 +723,7 @@ uart1: serial at 1c28400 {
>  			clocks = <&ccu CLK_BUS_UART1>;
>  			resets = <&ccu RST_BUS_UART1>;
>  			dmas = <&dma 7>, <&dma 7>;
> -			dma-names = "rx", "tx";
> +			dma-names = "tx", "rx";
>  			status = "disabled";
>  		};
> 
> @@ -736,7 +736,7 @@ uart2: serial at 1c28800 {
>  			clocks = <&ccu CLK_BUS_UART2>;
>  			resets = <&ccu RST_BUS_UART2>;
>  			dmas = <&dma 8>, <&dma 8>;
> -			dma-names = "rx", "tx";
> +			dma-names = "tx", "rx";
>  			status = "disabled";
>  		};
> 
> @@ -749,7 +749,7 @@ uart3: serial at 1c28c00 {
>  			clocks = <&ccu CLK_BUS_UART3>;
>  			resets = <&ccu RST_BUS_UART3>;
>  			dmas = <&dma 9>, <&dma 9>;
> -			dma-names = "rx", "tx";
> +			dma-names = "tx", "rx";
>  			status = "disabled";
>  		};







More information about the linux-riscv mailing list