[PATCH 2/2] mailbox: mpfs: read the system controller's status

[Conor Dooley]

From: Conor Dooley <conor.dooley at microchip.com>

Some services explicitly return an error code in their response, but
others rely on the system controller to set a status in its status
register. The meaning of the bits varies based on what service is
requested, so pass it back up to the driver that requested the service
in the first place. The field in the message struct already existed, but
was unused until now.

If the system controller is busy, in which case we should never actually
be in the interrupt handler, or if the service fails the mailbox itself
should not be read. Callers should check the status before operating on
the response.

Fixes: 83d7b1560810 ("mbox: add polarfire soc system controller mailbox")
Signed-off-by: Conor Dooley <conor.dooley at microchip.com>
---
 drivers/mailbox/mailbox-mpfs.c | 31 +++++++++++++++++++++++++++++--
 1 file changed, 29 insertions(+), 2 deletions(-)

diff --git a/drivers/mailbox/mailbox-mpfs.c b/drivers/mailbox/mailbox-mpfs.c
index cfacb3f320a6..e9a72c5453e4 100644
--- a/drivers/mailbox/mailbox-mpfs.c
+++ b/drivers/mailbox/mailbox-mpfs.c
@@ -2,7 +2,7 @@
 /*
  * Microchip PolarFire SoC (MPFS) system controller/mailbox controller driver
  *
- * Copyright (c) 2020 Microchip Corporation. All rights reserved.
+ * Copyright (c) 2020-2022 Microchip Corporation. All rights reserved.
  *
  * Author: Conor Dooley <conor.dooley at microchip.com>
  *
@@ -23,6 +23,8 @@
 #define MAILBOX_REG_OFFSET		0x800u
 #define MSS_SYS_MAILBOX_DATA_OFFSET	0u
 #define SCB_MASK_WIDTH			16u
+#define SCB_STATUS_SHIFT		16u
+#define SCB_STATUS_MASK			GENMASK(31, SCB_STATUS_SHIFT)
 
 /* SCBCTRL service control register */
 
@@ -130,13 +132,38 @@ static void mpfs_mbox_rx_data(struct mbox_chan *chan)
 	struct mpfs_mbox *mbox = (struct mpfs_mbox *)chan->con_priv;
 	struct mpfs_mss_response *response = mbox->response;
 	u16 num_words = ALIGN((response->resp_size), (4)) / 4U;
-	u32 i;
+	u32 i, status;
 
 	if (!response->resp_msg) {
 		dev_err(mbox->dev, "failed to assign memory for response %d\n", -ENOMEM);
 		return;
 	}
 
+	/*
+	 * The status is stored in bits 31:16 of the SERVICES_SR register.
+	 * It is only valid when BUSY == 0.
+	 * We should *never* get an interrupt while the controller is
+	 * still in the busy state. If we do, something has gone badly
+	 * wrong & the content of the mailbox would not be valid.
+	 */
+	if (mpfs_mbox_busy(mbox)) {
+		dev_err(mbox->dev, "got an interrupt but system controller is busy\n");
+		response->resp_status = 0xDEAD;
+		return;
+	}
+
+	status = readl_relaxed(mbox->ctrl_base + SERVICES_SR_OFFSET);
+
+	/*
+	 * If the status of the individual servers is non-zero, the service has
+	 * failed. The contents of the mailbox at this point are not be valid,
+	 * so don't bother reading them. Set the status so that the driver
+	 * implementing the service can handle the result.
+	 */
+	response->resp_status = (status & SCB_STATUS_MASK); >> SCB_STATUS_SHIFT;
+	if (response->resp_status)
+		return;
+
 	if (!mpfs_mbox_busy(mbox)) {
 		for (i = 0; i < num_words; i++) {
 			response->resp_msg[i] =
-- 
2.37.2