[PATCH] i2c: add support for microchip fpga i2c controllers

[Ben Dooks]

On 15/03/2022 15:32, Conor Dooley wrote:
> Add Microchip CoreI2C i2c controller support. This driver supports the
> "hard" i2c controller on the Microchip PolarFire SoC & the basic feature
> set for "soft" i2c controller implemtations in the FPGA fabric.
> 
> Co-developed-by: Daire McNamara <daire.mcnamara at microchip.com>
> Signed-off-by: Daire McNamara <daire.mcnamara at microchip.com>
> Signed-off-by: Conor Dooley <conor.dooley at microchip.com>
> ---
>   drivers/i2c/busses/Kconfig              |  11 +
>   drivers/i2c/busses/Makefile             |   1 +
>   drivers/i2c/busses/i2c-microchip-core.c | 487 ++++++++++++++++++++++++
>   3 files changed, 499 insertions(+)
>   create mode 100644 drivers/i2c/busses/i2c-microchip-core.c
> 
> diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
> index a1bae59208e3..3d4d8e0e9de7 100644
> --- a/drivers/i2c/busses/Kconfig
> +++ b/drivers/i2c/busses/Kconfig
> @@ -781,6 +781,17 @@ config I2C_MESON
>   	  If you say yes to this option, support will be included for the
>   	  I2C interface on the Amlogic Meson family of SoCs.
>   

snip

> +
> +static void mchp_corei2c_core_disable(struct mchp_corei2c_dev *idev)
> +{
> +	u8 ctrl = readl(idev->base + CORE_I2C_CTRL);
> +
> +	ctrl &= ~CTRL_ENS1;
> +	writel(ctrl, idev->base + CORE_I2C_CTRL);
> +}
> +
> +static void mchp_corei2c_core_enable(struct mchp_corei2c_dev *idev)
> +{
> +	u8 ctrl = readl(idev->base + CORE_I2C_CTRL);
> +
> +	ctrl |= CTRL_ENS1;
> +	writel(ctrl, idev->base + CORE_I2C_CTRL);
> +}

Not sure why you would use readl/writel with an u8, surely an
readb/writeb be better?


> +static irqreturn_t mchp_corei2c_handle_isr(struct mchp_corei2c_dev *idev)
> +{
> +	u32 status = idev->isr_status;
> +	u8 ctrl;
> +
> +	if (!idev->buf) {
> +		dev_warn(idev->dev, "unexpected interrupt\n");
> +		return IRQ_HANDLED;
> +	}

is IRQ_HANDLED correct here?

> +
> +static int mchp_corei2c_probe(struct platform_device *pdev)
> +{
> +	struct mchp_corei2c_dev *idev = NULL;
> +	struct resource *res;
> +	int irq, ret;
> +	u32 val;
> +
> +	idev = devm_kzalloc(&pdev->dev, sizeof(*idev), GFP_KERNEL);
> +	if (!idev)
> +		return -ENOMEM;
> +
> +	idev->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
> +	if (IS_ERR(idev->base))
> +		return PTR_ERR(idev->base);
> +
> +	irq = platform_get_irq(pdev, 0);
> +	if (irq < 0)
> +		return dev_err_probe(&pdev->dev, irq,
> +				     "missing interrupt resource\n");
> +
> +	idev->i2c_clk = devm_clk_get(&pdev->dev, NULL);
> +	if (IS_ERR(idev->i2c_clk))
> +		return dev_err_probe(&pdev->dev, PTR_ERR(idev->i2c_clk),
> +				     "missing clock\n");
> +
> +	idev->dev = &pdev->dev;
> +	init_completion(&idev->msg_complete);
> +	spin_lock_init(&idev->lock);
> +
> +	val = device_property_read_u32(idev->dev, "clock-frequency",
> +				       &idev->bus_clk_rate);
> +	if (val) {
> +		dev_info(&pdev->dev, "default to 100kHz\n");
> +		idev->bus_clk_rate = 100000;
> +	}
> +
> +	if (idev->bus_clk_rate > 400000)
> +		return dev_err_probe(&pdev->dev, -EINVAL,
> +				     "clock-frequency too high: %d\n",
> +				     idev->bus_clk_rate);
> +
> +	ret = devm_request_irq(&pdev->dev, irq, mchp_corei2c_isr, IRQF_SHARED,
> +			       pdev->name, idev);
> +	if (ret)
> +		return dev_err_probe(&pdev->dev, ret,
> +				     "failed to claim irq %d\n", irq);
> +
> +	ret = clk_prepare_enable(idev->i2c_clk);
> +	if (ret)
> +		return dev_err_probe(&pdev->dev, ret,
> +				     "failed to enable clock\n");
> +
> +	ret = mchp_corei2c_init(idev);
> +	if (ret)
> +		return dev_err_probe(&pdev->dev, ret,
> +				     "failed to program clock divider\n");

going to leak a prepared clock from here on?

> +	i2c_set_adapdata(&idev->adapter, idev);
> +	snprintf(idev->adapter.name, sizeof(idev->adapter.name),
> +		 "Microchip I2C hw bus");
> +	idev->adapter.owner = THIS_MODULE;
> +	idev->adapter.algo = &mchp_corei2c_algo;
> +	idev->adapter.dev.parent = &pdev->dev;
> +	idev->adapter.dev.of_node = pdev->dev.of_node;
> +
> +	platform_set_drvdata(pdev, idev);
> +
> +	ret = i2c_add_adapter(&idev->adapter);
> +	if (ret) {
> +		clk_disable_unprepare(idev->i2c_clk);
> +		return ret;
> +	}
> +
> +	dev_info(&pdev->dev, "Microchip I2C Probe Complete\n");

not sure if necessary, doesn't the i2c core also announce?

> +	return 0;
> +}
> +
> +static int mchp_corei2c_remove(struct platform_device *pdev)
> +{
> +	struct mchp_corei2c_dev *idev = platform_get_drvdata(pdev);
> +
> +	clk_disable_unprepare(idev->i2c_clk);
> +	i2c_del_adapter(&idev->adapter);
> +
> +	return 0;
> +}
> +
> +static const struct of_device_id mchp_corei2c_of_match[] = {
> +	{ .compatible = "microchip,mpfs-i2c" },
> +	{ .compatible = "microchip,corei2c-rtl-v7" },
> +	{},
> +};
> +MODULE_DEVICE_TABLE(of, mchp_corei2c_of_match);
> +
> +static struct platform_driver mchp_corei2c_driver = {
> +	.probe = mchp_corei2c_probe,
> +	.remove = mchp_corei2c_remove,
> +	.driver = {
> +		.name = "microchip-corei2c",
> +		.of_match_table = mchp_corei2c_of_match,
> +	},
> +};
> +
> +module_platform_driver(mchp_corei2c_driver);
> +
> +MODULE_DESCRIPTION("Microchip CoreI2C bus driver");
> +MODULE_AUTHOR("Daire McNamara <daire.mcnamara at microchip.com>");
> +MODULE_AUTHOR("Conor Dooley <conor.dooley at microchip.com>");
> +MODULE_LICENSE("GPL v2");


-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

https://www.codethink.co.uk/privacy.html