[PATCH v1 1/6] dt-bindings: mmc: convert mmc-spi-slot to yaml

[Krzysztof Kozlowski]

On 05/06/2022 15:32, mail at conchuod.ie wrote:
> From: Conor Dooley <conor.dooley at microchip.com>
> 
> Convert the mmc-spi-slot text based binding doc to yaml,
> with the side effect of cleaning up some of the riscv
> dtbs_check warnings.
> 
> Signed-off-by: Conor Dooley <conor.dooley at microchip.com>
> ---
>  .../devicetree/bindings/mmc/mmc-spi-slot.txt  | 29 -------
>  .../devicetree/bindings/mmc/mmc-spi-slot.yaml | 76 +++++++++++++++++++
>  2 files changed, 76 insertions(+), 29 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
>  create mode 100644 Documentation/devicetree/bindings/mmc/mmc-spi-slot.yaml
> 
> diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
> deleted file mode 100644
> index 5e74db69f581..000000000000
> --- a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.txt
> +++ /dev/null
> @@ -1,29 +0,0 @@
> -MMC/SD/SDIO slot directly connected to a SPI bus
> -
> -This file documents differences between the core properties described
> -by mmc.txt and the properties used by the mmc_spi driver.
> -
> -Required properties:
> -- spi-max-frequency : maximum frequency for this device (Hz).
> -
> -Optional properties:
> -- voltage-ranges : two cells are required, first cell specifies minimum
> -  slot voltage (mV), second cell specifies maximum slot voltage (mV).
> -  Several ranges could be specified. If not provided, 3.2v..3.4v is assumed.
> -- gpios : may specify GPIOs in this order: Card-Detect GPIO,
> -  Write-Protect GPIO. Note that this does not follow the
> -  binding from mmc.txt, for historical reasons.
> -
> -Example:
> -
> -	mmc-slot at 0 {
> -		compatible = "fsl,mpc8323rdb-mmc-slot",
> -			     "mmc-spi-slot";
> -		reg = <0>;
> -		gpios = <&qe_pio_d 14 1
> -			 &qe_pio_d 15 0>;
> -		voltage-ranges = <3300 3300>;
> -		spi-max-frequency = <50000000>;
> -		interrupts = <42>;
> -		interrupt-parent = <&PIC>;
> -	};
> diff --git a/Documentation/devicetree/bindings/mmc/mmc-spi-slot.yaml b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.yaml
> new file mode 100644
> index 000000000000..a5fd723140c9
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mmc/mmc-spi-slot.yaml
> @@ -0,0 +1,76 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mmc/mmc-spi-slot.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: MMC/SD/SDIO slot directly connected to a SPI bus
> +
> +maintainers:
> +  - Ulf Hansson <ulf.hansson at linaro.org>
> +
> +allOf:
> +  - $ref: "mmc-controller.yaml"
> +
> +description: |
> +  The extra properties used by an mmc connected via spi.

s/spi/SPI/

> +
> +properties:
> +  compatible:
> +    const: "mmc-spi-slot"

No quotes, please.

> +
> +  reg:
> +    maxItems: 1
> +
> +  spi-max-frequency: true

I think instead you should reference:
/schemas/spi/spi-peripheral-props.yaml
(because also other properties might be needed for different SPI
controllers)

> +
> +  interrupts:
> +    maxItems: 1
> +
> +  voltage-ranges:
> +    $ref: '/schemas/types.yaml#/definitions/uint32-matrix'

Here as well - quotes are not needed. Some schemas have it, some not,
but I guess shorter is preferred :)

> +    description: |
> +      Two cells are required, first cell specifies minimum slot voltage (mV),
> +      second cell specifies maximum slot voltage (mV).
> +    items:
> +      items:
> +        - description: |
> +            value for minimum slot voltage
> +          default: 3200
> +        - description: |
> +            value for maximum slot voltage
> +          default: 3400
> +    maxItems: 1
> +
> +  gpios:
> +    description: |
> +      For historical reasons, this does not follow the generic mmc-controller binding.
> +    minItems: 1
> +    items:
> +      - description: Card-Detect GPIO
> +      - description: Write-Protect GPIO
> +
> +required:
> +  - compatible
> +  - reg
> +  - spi-max-frequency
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    spi {
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +      mmc at 0 {
> +        compatible = "mmc-spi-slot";
> +        reg = <0>;
> +        gpios = <&qe_pio_d 14 1>, <&qe_pio_d 15 0>;

The GPIO flags should be common defines instead.

> +        voltage-ranges = <3300 3300>;
> +        spi-max-frequency = <50000000>;
> +        interrupts = <42>;
> +        interrupt-parent = <&PIC>;
> +      };
> +    };
> +
> +...


Best regards,
Krzysztof