[PATCH v4 3/3] dmaengine: sf-pdma: Get number of channel by device tree

[Palmer Dabbelt]

On Sun, 16 Jan 2022 17:35:28 PST (-0800), zong.li at sifive.com wrote:
> It currently assumes that there are always four channels, it would
> cause the error if there is actually less than four channels. Change
> that by getting number of channel from device tree.
>
> For backwards-compatible, it uses the default value (i.e. 4) when there
> is no 'dma-channels' information in dts.

Some of the same wording issues here as those I pointed out in the DT 
bindings patch.

> Signed-off-by: Zong Li <zong.li at sifive.com>
> ---
>  drivers/dma/sf-pdma/sf-pdma.c | 20 +++++++++++++-------
>  drivers/dma/sf-pdma/sf-pdma.h |  8 ++------
>  2 files changed, 15 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/dma/sf-pdma/sf-pdma.c b/drivers/dma/sf-pdma/sf-pdma.c
> index f12606aeff87..1264add9897e 100644
> --- a/drivers/dma/sf-pdma/sf-pdma.c
> +++ b/drivers/dma/sf-pdma/sf-pdma.c
> @@ -482,9 +482,7 @@ static void sf_pdma_setup_chans(struct sf_pdma *pdma)
>  static int sf_pdma_probe(struct platform_device *pdev)
>  {
>  	struct sf_pdma *pdma;
> -	struct sf_pdma_chan *chan;
>  	struct resource *res;
> -	int len, chans;
>  	int ret;
>  	const enum dma_slave_buswidth widths =
>  		DMA_SLAVE_BUSWIDTH_1_BYTE | DMA_SLAVE_BUSWIDTH_2_BYTES |
> @@ -492,13 +490,21 @@ static int sf_pdma_probe(struct platform_device *pdev)
>  		DMA_SLAVE_BUSWIDTH_16_BYTES | DMA_SLAVE_BUSWIDTH_32_BYTES |
>  		DMA_SLAVE_BUSWIDTH_64_BYTES;
>
> -	chans = PDMA_NR_CH;
> -	len = sizeof(*pdma) + sizeof(*chan) * chans;
> -	pdma = devm_kzalloc(&pdev->dev, len, GFP_KERNEL);
> +	pdma = devm_kzalloc(&pdev->dev, sizeof(*pdma), GFP_KERNEL);
>  	if (!pdma)
>  		return -ENOMEM;
>
> -	pdma->n_chans = chans;
> +	ret = of_property_read_u32(pdev->dev.of_node, "dma-channels",
> +				   &pdma->n_chans);
> +	if (ret) {
> +		dev_notice(&pdev->dev, "set number of channels to default value: 4\n");
> +		pdma->n_chans = PDMA_MAX_NR_CH;
> +	}
> +
> +	if (pdma->n_chans > PDMA_MAX_NR_CH) {
> +		dev_err(&pdev->dev, "the number of channels exceeds the maximum\n");
> +		return -EINVAL;

Can we get away with just using only the number of channels the driver 
actually supports?  ie, just never sending an op to the channels above 
MAX_NR_CH?  That should leave us with nothing to track.

> +	}
>
>  	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>  	pdma->membase = devm_ioremap_resource(&pdev->dev, res);
> @@ -556,7 +562,7 @@ static int sf_pdma_remove(struct platform_device *pdev)
>  	struct sf_pdma_chan *ch;
>  	int i;
>
> -	for (i = 0; i < PDMA_NR_CH; i++) {
> +	for (i = 0; i < pdma->n_chans; i++) {
>  		ch = &pdma->chans[i];
>
>  		devm_free_irq(&pdev->dev, ch->txirq, ch);
> diff --git a/drivers/dma/sf-pdma/sf-pdma.h b/drivers/dma/sf-pdma/sf-pdma.h
> index 0c20167b097d..8127d792f639 100644
> --- a/drivers/dma/sf-pdma/sf-pdma.h
> +++ b/drivers/dma/sf-pdma/sf-pdma.h
> @@ -22,11 +22,7 @@
>  #include "../dmaengine.h"
>  #include "../virt-dma.h"
>
> -#define PDMA_NR_CH					4
> -
> -#if (PDMA_NR_CH != 4)
> -#error "Please define PDMA_NR_CH to 4"
> -#endif
> +#define PDMA_MAX_NR_CH					4
>
>  #define PDMA_BASE_ADDR					0x3000000
>  #define PDMA_CHAN_OFFSET				0x1000
> @@ -118,7 +114,7 @@ struct sf_pdma {
>  	void __iomem            *membase;
>  	void __iomem            *mappedbase;
>  	u32			n_chans;
> -	struct sf_pdma_chan	chans[PDMA_NR_CH];
> +	struct sf_pdma_chan	chans[PDMA_MAX_NR_CH];
>  };
>
>  #endif /* _SF_PDMA_H */