[PATCH v2 3/5] dt-bindings: pinctrl: Add StarFive JH7110 aon pinctrl

Emil Renner Berthing emil.renner.berthing at canonical.com
Wed Dec 7 05:21:06 PST 2022


On Mon, 28 Nov 2022 at 02:15, Jianlong Huang
<jianlong.huang at starfivetech.com> wrote:
>
> On Mon, 21 Nov 2022 09:44:00 +0100, Krzysztof Kozlowski wrote:
> > On 18/11/2022 02:11, Hal Feng wrote:
> >> From: Jianlong Huang <jianlong.huang at starfivetech.com>
> >>
> >> Add pinctrl bindings for StarFive JH7110 SoC aon pinctrl controller.
> >>
> >> Signed-off-by: Jianlong Huang <jianlong.huang at starfivetech.com>
> >> Signed-off-by: Hal Feng <hal.feng at starfivetech.com>
> >> ---
> >>  .../pinctrl/starfive,jh7110-aon-pinctrl.yaml  | 134 ++++++++++++++++++
> >>  1 file changed, 134 insertions(+)
> >>  create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7110-aon-pinctrl.yaml
> >>
> >> diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-aon-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-aon-pinctrl.yaml
> >> new file mode 100644
> >> index 000000000000..1dd000e1f614
> >> --- /dev/null
> >> +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7110-aon-pinctrl.yaml
> >> @@ -0,0 +1,134 @@
> >> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> >> +%YAML 1.2
> >> +---
> >> +$id: http://devicetree.org/schemas/pinctrl/starfive,jh7110-aon-pinctrl.yaml#
> >> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> >> +
> >> +title: StarFive JH7110 Aon Pin Controller
> >> +
> >> +description: |
> >> +  Bindings for the JH7110 RISC-V SoC from StarFive Technology Ltd.
> >> +
> >> +  Out of the SoC's many pins only the ones named PAD_GPIO0 to PAD_GPIO4
> >> +  can be multiplexed and have configurable bias, drive strength,
> >> +  schmitt trigger etc.
> >> +  Some peripherals have their I/O go through the 4 "GPIOs". This also
> >> +  includes PWM.
> >> +
> >> +maintainers:
> >> +  - Jianlong Huang <jianlong.huang at starfivetech.com>
> >> +
> >> +properties:
> >> +  compatible:
> >> +    const: starfive,jh7110-aon-pinctrl
> >> +
> >> +  reg:
> >> +    maxItems: 1
> >> +
> >> +  reg-names:
> >> +    items:
> >> +      - const: control

Again this doesn't seem necessary when you only have 1 memory range.

> >> +
> >> +  clocks:
> >> +    maxItems: 1
> >> +
> >> +  resets:
> >> +    maxItems: 1
> >> +
> >> +  gpio-controller: true
> >> +
> >> +  "#gpio-cells":
> >> +    const: 2
> >> +
> >> +  interrupts:
> >> +    maxItems: 1
> >> +    description: The GPIO parent interrupt.
> >
> > Same comments apply plus one more.
>
> Will fix, drop this description.
>
> >
> >> +
> >> +  interrupt-controller: true
> >> +
> >> +  "#interrupt-cells":
> >> +    const: 2
> >> +
> >> +required:
> >> +  - compatible
> >> +  - reg
> >> +  - reg-names
> >> +  - gpio-controller
> >> +  - "#gpio-cells"
> >> +  - interrupts
> >> +  - interrupt-controller
> >> +  - "#interrupt-cells"
> >
> > "required:" goes after patternProperties.
>
> Will fix.
>
> >
> >> +
> >> +patternProperties:
> >> +  '-[0-9]+$':
> >
> > Same comment.
>
> Will fix.
> Keep consistent quotes, use '
>
> >
> >> +    type: object
> >> +    patternProperties:
> >> +      '-pins$':
> >> +        type: object
> >> +        description: |
> >> +          A pinctrl node should contain at least one subnode representing the
> >> +          pinctrl groups available on the machine. Each subnode will list the
> >> +          pins it needs, and how they should be configured, with regard to
> >> +          muxer configuration, system signal configuration, pin groups for
> >> +          vin/vout module, pin voltage, mux functions for output, mux functions
> >> +          for output enable, mux functions for input.
> >> +
> >> +        properties:
> >> +          pinmux:
> >> +            description: |
> >> +              The list of GPIOs and their mux settings that properties in the
> >> +              node apply to. This should be set using the GPIOMUX macro.
> >> +            $ref: "/schemas/pinctrl/pinmux-node.yaml#/properties/pinmux"
> >> +
> >> +          bias-disable: true
> >> +
> >> +          bias-pull-up:
> >> +            type: boolean
> >> +
> >> +          bias-pull-down:
> >> +            type: boolean
> >> +
> >> +          drive-strength:
> >> +            enum: [ 2, 4, 8, 12 ]
> >> +
> >> +          input-enable: true
> >> +
> >> +          input-disable: true
> >> +
> >> +          input-schmitt-enable: true
> >> +
> >> +          input-schmitt-disable: true
> >> +
> >> +          slew-rate:
> >> +            maximum: 1
> >> +
> >> +        additionalProperties: false
> >> +
> >> +    additionalProperties: false
> >> +
> >> +additionalProperties: false
> >> +
> >> +examples:
> >> +  - |
> >> +    #include <dt-bindings/clock/starfive-jh7110.h>
> >> +    #include <dt-bindings/reset/starfive-jh7110.h>
> >> +    #include <dt-bindings/pinctrl/pinctrl-starfive-jh7110.h>
> >> +
> >> +        soc {
> >> +                #address-cells = <2>;
> >> +                #size-cells = <2>;

Again these two lines can be dropped..

> >
> > Same comment.
>
> Will fix.
> Use 4 spaces for example indentation.
>
> >
> >> +
> >> +                gpioa: gpio at 17020000 {
> >> +                        compatible = "starfive,jh7110-aon-pinctrl";
> >> +                        reg = <0x0 0x17020000 0x0 0x10000>;

..if you just change this to
reg = <0x17020000 0x10000>;

> >> +                        reg-names = "control";
> >> +                        resets = <&aoncrg_rst JH7110_AONRST_AON_IOMUX>;
> >> +                        interrupts = <85>;
> >> +                        interrupt-controller;
> >> +                        #interrupt-cells = <2>;
> >> +                        #gpio-cells = <2>;
> >> +                        gpio-controller;
> >> +                };
> >> +        };
> >> +
> >> +...
> >
>
> Best regards,
> Jianlong Huang
>
>



More information about the linux-riscv mailing list