[RFC PATCH V4 6/6] riscv: soc: Add Allwinner SoC kconfig option

[Guo Ren]

On Tue, Sep 14, 2021 at 5:30 PM Arnd Bergmann <arnd at arndb.de> wrote:
>
> On Tue, Sep 14, 2021 at 4:36 AM Guo Ren <guoren at kernel.org> wrote:
> > On Tue, Sep 14, 2021 at 2:49 AM Randy Dunlap <rdunlap at infradead.org> wrote:
> > > On 9/13/21 2:20 AM, Guo Ren wrote:
> > > > On Mon, Sep 13, 2021 at 4:45 PM Maxime Ripard <maxime at cerno.tech> wrote:
> > > >> On Sat, Sep 11, 2021 at 05:21:39PM +0800, guoren at kernel.org wrote:
> > > >>> From: Liu Shaohua <liush at allwinnertech.com>
> > > >>>
> > > >>> Add Allwinner kconfig option which selects SoC specific and common
> > > >>> drivers that is required for this SoC.
> > > >>>
> > > >>> Allwinner D1 uses custom PTE attributes to solve non-coherency SOC
> > > >>> interconnect issues for dma synchronization, so we set the default
> > > >>> value when SOC_SUNXI selected.
> > > >>>
> > > >>>
> > > >>> +config SOC_SUNXI
> > > >>> +     bool "Allwinner SoCs"
> > > >>> +     depends on MMU
> > > >>> +     select DWMAC_GENERIC
> > > >>> +     select ERRATA_THEAD
> > > >>> +     select RISCV_DMA_NONCOHERENT
> > > >>> +     select RISCV_ERRATA_ALTERNATIVE
> > > >>> +     select SERIAL_8250
> > > >>> +     select SERIAL_8250_CONSOLE
> > > >>> +     select SERIAL_8250_DW
> > > >>> +     select SIFIVE_PLIC
> > > >>> +     select STMMAC_ETH
> > > >>> +     help
> > > >>> +       This enables support for Allwinner SoC platforms like the D1.
> > > >>> +
> > > >>
> > > >> I'm not sure we should select the drivers there. We could very well
> > > >> imagine a board without UART, or even more so without ethernet.
> > > > We just want people could bring D1 up easier, 8250 is the basic component.
> > > >
> > > >
> > > >>
> > > >> These options should be in the defconfig.
> > >
> > > Agreed, using a defconfig is the right way to do this.
> > Put 8250 related configs into arch/riscv/configs/defconfig?
>
> I think that would be best, as well as the STMMAC_ETH and
> DWMAC_GENERIC options.
Okay, I would move STMMAC_ETH SERIAL_8250_DW SERIAL_8250_CONSOLE
SERIAL_8250 & SIFIVE_PLIC into defconfig in the next version of the
patch.

>
> If all RISC-V chips are required to have a 8250 compatible uart,
> selecting it from CONFIG_RISCV would work as well, but for
> consistency I'd give users the option to leave it out, just like
> any other driver that is not required to have a useful system.
>
> >  @Palmer Dabbelt @Arnd Bergmann, How do you think about that?
> > (defconfig or Kconfig.soc)
> > My purpose is when people make the Image from riscv/defconfig, then
> > the Image could run on all platforms include D1.
>
> I would try to keep the Kconfig.soc as short as possible. As a general
> rule, only use 'select' to enable symbols that are otherwise not user
> visible, such as the specific errata if you want to hide them. For individual
> SoCs, I prefer not having separate Kconfig options, but instead have
> those per driver. We have some SoC families that have part specific
> options elsewhere, e.g. drivers/soc/renesas/Kconfig, but I'd only add
> those if you can't avoid it. Having it in drivers/soc/ may be better for
> sunxi than spreading them over arch/{arm,arm64,riscv}.
>
> Some subsystem maintainers want drivers to be selected by the SoC
> option, this is why you need the 'select SIFIVE_PLIC', but usually
> the drivers are selectable with a 'depends on ARCH_SUNXI ||
> COMPILE_TEST' and enabled in the defconfig.
>
> If you want to get fancy, you can use something like:
>
> config RESET_SUNXI
>         bool "Allwinner SoCs Reset Driver" if COMPILE_TEST && !ARCH_SUNXI
>         default ARCH_SUNXI
>
> This will make an option that
>  - always enabled when the platform is built-in
>  - user selectable when compile-testing for any other platform
>  - always disabled otherwise
>
>        Arnd



-- 
Best Regards
 Guo Ren

ML: https://lore.kernel.org/linux-csky/