[PATCH v2 11/43] KVM: Don't block+unblock when halt-polling is successful

Maxim Levitsky mlevitsk at redhat.com
Wed Oct 27 06:40:40 PDT 2021


On Fri, 2021-10-08 at 19:12 -0700, Sean Christopherson wrote:
> Invoke the arch hooks for block+unblock if and only if KVM actually
> attempts to block the vCPU.  The only non-nop implementation is on x86,
> specifically SVM's AVIC, and there is no need to put the AVIC prior to
> halt-polling as KVM x86's kvm_vcpu_has_events() will scour the full vIRR
> to find pending IRQs regardless of whether the AVIC is loaded/"running".
> 
> The primary motivation is to allow future cleanup to split out "block"
> from "halt", but this is also likely a small performance boost on x86 SVM
> when halt-polling is successful.
> 
> Adjust the post-block path to update "cur" after unblocking, i.e. include
> AVIC load time in halt_wait_ns and halt_wait_hist, so that the behavior
> is consistent.  Moving just the pre-block arch hook would result in only
> the AVIC put latency being included in the halt_wait stats.  There is no
> obvious evidence that one way or the other is correct, so just ensure KVM
> is consistent.
> 
> Note, x86 has two separate paths for handling APICv with respect to vCPU
> blocking.  VMX uses hooks in x86's vcpu_block(), while SVM uses the arch
> hooks in kvm_vcpu_block().  Prior to this path, the two paths were more
> or less functionally identical.  That is very much not the case after
> this patch, as the hooks used by VMX _must_ fire before halt-polling.
> x86's entire mess will be cleaned up in future patches.
> 
> Signed-off-by: Sean Christopherson <seanjc at google.com>
> ---
>  virt/kvm/kvm_main.c | 7 ++++---
>  1 file changed, 4 insertions(+), 3 deletions(-)
> 
> diff --git a/virt/kvm/kvm_main.c b/virt/kvm/kvm_main.c
> index f90b3ed05628..227f6bbe0716 100644
> --- a/virt/kvm/kvm_main.c
> +++ b/virt/kvm/kvm_main.c
> @@ -3235,8 +3235,6 @@ void kvm_vcpu_block(struct kvm_vcpu *vcpu)
>  	bool waited = false;
>  	u64 block_ns;
>  
> -	kvm_arch_vcpu_blocking(vcpu);
> -
>  	start = cur = poll_end = ktime_get();
>  	if (do_halt_poll) {
>  		ktime_t stop = ktime_add_ns(ktime_get(), vcpu->halt_poll_ns);
> @@ -3253,6 +3251,7 @@ void kvm_vcpu_block(struct kvm_vcpu *vcpu)
>  		} while (kvm_vcpu_can_poll(cur, stop));
>  	}
>  
> +	kvm_arch_vcpu_blocking(vcpu);
>  
>  	prepare_to_rcuwait(wait);
>  	for (;;) {
> @@ -3265,6 +3264,9 @@ void kvm_vcpu_block(struct kvm_vcpu *vcpu)
>  		schedule();
>  	}
>  	finish_rcuwait(wait);
> +
> +	kvm_arch_vcpu_unblocking(vcpu);
> +
>  	cur = ktime_get();
>  	if (waited) {
>  		vcpu->stat.generic.halt_wait_ns +=
> @@ -3273,7 +3275,6 @@ void kvm_vcpu_block(struct kvm_vcpu *vcpu)
>  				ktime_to_ns(cur) - ktime_to_ns(poll_end));
>  	}
>  out:
> -	kvm_arch_vcpu_unblocking(vcpu);
>  	block_ns = ktime_to_ns(cur) - ktime_to_ns(start);
>  
>  	/*

Makes sense.

Reviewed-by: Maxim Levitsky <mlevitsk at redhat.com>

Best regards,
	Maxim Levitsky




More information about the linux-riscv mailing list