[PATCH v1 11/16] dt-bindings: pinctrl: Add StarFive JH7100 bindings

Emil Renner Berthing kernel at esmil.dk
Tue Oct 12 06:40:22 PDT 2021


Add bindings for the StarFive JH7100 gpio/pin controller.

Signed-off-by: Emil Renner Berthing <kernel at esmil.dk>
---
 .../pinctrl/starfive,jh7100-pinctrl.yaml      | 274 ++++++++++++++++++
 1 file changed, 274 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml

diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml
new file mode 100644
index 000000000000..342ecd91a3b0
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml
@@ -0,0 +1,274 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/starfive,jh7100-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: StarFive JH7100 Pin Controller Device Tree Bindings
+
+maintainers:
+  - Emil Renner Berthing <kernel at esmil.dk>
+  - Drew Fustini <drew at beagleboard.org>
+
+properties:
+  compatible:
+    const: starfive,jh7100-pinctrl
+
+  reg:
+    minItems: 2
+    maxItems: 2
+
+  reg-names:
+    items:
+      - const: "gpio"
+      - const: "padctl"
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  gpio-controller: true
+
+  "#gpio-cells":
+    const: 2
+    description: |
+      Number of cells in GPIO specifier. Since the generic GPIO
+      binding is used, the amount of cells must be specified as 2.
+
+  interrupts:
+    maxItems: 1
+    description: The GPIO parent interrupt.
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 2
+
+  starfive,signal-group:
+    description: |
+      The SoC has a global setting selecting one of 7 different pinmux
+      configurations of the pads named GPIO[0:63] and FUNC_SHARE[0:141]. After
+      this global setting is chosen only the 64 "GPIO" pins can be further
+      muxed by configuring them to be controlled by certain peripherals rather
+      than software.
+      Note that in configuration 0 none of GPIOs are routed to pads, and only
+      in configuration 1 are the GPIOs routed to the pads named GPIO[0:63].
+      If this property is not set it defaults to the configuration already
+      chosen by the earlier boot stages.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [0, 1, 2, 3, 4, 5, 6]
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - clocks
+  - gpio-controller
+  - "#gpio-cells"
+  - interrupts
+  - interrupt-controller
+  - "#interrupt-cells"
+
+patternProperties:
+  '-[0-9]*$':
+    type: object
+    patternProperties:
+      '-pins*$':
+        type: object
+        description: |
+          A pinctrl node should contain at least one subnode representing the
+          pinctrl groups available on the machine. Each subnode will list the
+          pins it needs, and how they should be configured, with regard to
+          muxer configuration, bias, input enable/disable, input schmitt
+          trigger enable/disable, slew-rate and drive strength.
+        $ref: "/schemas/pinctrl/pincfg-node.yaml"
+
+        properties:
+          pins:
+            description: |
+              The list of pin identifiers that properties in the node apply to.
+              This should be set using either the PAD_GPIO or PAD_FUNC_SHARE
+              macro. Either this or "pinmux" has to be specified.
+
+          pinmux:
+            description: |
+              The list of GPIO identifiers and their mux settings that
+              properties in the node apply to. This should be set using the
+              GPIOMUX macro. Either this or "pins" has to be specified.
+
+          bias-disable: true
+
+          bias-pull-up:
+            type: boolean
+
+          bias-pull-down:
+            type: boolean
+
+          drive-strength:
+            enum: [ 14, 21, 28, 35, 42, 49, 56, 63 ]
+
+          input-enable: true
+
+          input-disable: true
+
+          input-schmitt-enable: true
+
+          input-schmitt-disable: true
+
+          slew-rate:
+            maximum: 7
+
+          starfive,strong-pull-up:
+            description: enable strong pull-up.
+            type: boolean
+
+        additionalProperties: false
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/starfive-jh7100.h>
+    #include <dt-bindings/reset/starfive-jh7100.h>
+    #include <dt-bindings/pinctrl/pinctrl-starfive.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        gpio: pinctrl at 11910000 {
+            compatible = "starfive,jh7100-pinctrl";
+            reg = <0x0 0x11910000 0x0 0x10000>,
+                  <0x0 0x11858000 0x0 0x1000>;
+            reg-names = "gpio", "padctl";
+            clocks = <&clkgen JH7100_CLK_GPIO_APB>;
+            resets = <&clkgen JH7100_RSTN_GPIO_APB>;
+            interrupts = <32>;
+            gpio-controller;
+            #gpio-cells = <2>;
+            interrupt-controller;
+            #interrupt-cells = <2>;
+            starfive,signal-group = <6>;
+
+            gmac_pins_default: gmac-0 {
+                gtxclk-pins {
+                    pins = <PAD_FUNC_SHARE(115)>;
+                    bias-pull-up;
+                    drive-strength = <35>;
+                    input-enable;
+                    input-schmitt-enable;
+                    slew-rate = <0>;
+                };
+                miitxclk-pins {
+                    pins = <PAD_FUNC_SHARE(116)>;
+                    bias-pull-up;
+                    drive-strength = <14>;
+                    input-enable;
+                    input-schmitt-disable;
+                    slew-rate = <0>;
+                };
+                tx-pins {
+                    pins = <PAD_FUNC_SHARE(117)>,
+                           <PAD_FUNC_SHARE(119)>,
+                           <PAD_FUNC_SHARE(120)>,
+                           <PAD_FUNC_SHARE(121)>,
+                           <PAD_FUNC_SHARE(122)>,
+                           <PAD_FUNC_SHARE(123)>,
+                           <PAD_FUNC_SHARE(124)>,
+                           <PAD_FUNC_SHARE(125)>,
+                           <PAD_FUNC_SHARE(126)>;
+                    bias-disable;
+                    drive-strength = <35>;
+                    input-disable;
+                    input-schmitt-disable;
+                    slew-rate = <0>;
+                };
+                rxclk-pins {
+                    pins = <PAD_FUNC_SHARE(127)>;
+                    bias-pull-up;
+                    drive-strength = <14>;
+                    input-enable;
+                    input-schmitt-disable;
+                    slew-rate = <6>;
+                };
+                rxer-pins {
+                    pins = <PAD_FUNC_SHARE(129)>;
+                    bias-pull-up;
+                    drive-strength = <14>;
+                    input-enable;
+                    input-schmitt-disable;
+                    slew-rate = <0>;
+                };
+                rx-pins {
+                    pins = <PAD_FUNC_SHARE(128)>,
+                           <PAD_FUNC_SHARE(130)>,
+                           <PAD_FUNC_SHARE(131)>,
+                           <PAD_FUNC_SHARE(132)>,
+                           <PAD_FUNC_SHARE(133)>,
+                           <PAD_FUNC_SHARE(134)>,
+                           <PAD_FUNC_SHARE(135)>,
+                           <PAD_FUNC_SHARE(136)>,
+                           <PAD_FUNC_SHARE(137)>,
+                           <PAD_FUNC_SHARE(138)>,
+                           <PAD_FUNC_SHARE(139)>,
+                           <PAD_FUNC_SHARE(140)>,
+                           <PAD_FUNC_SHARE(141)>;
+                    bias-pull-up;
+                    drive-strength = <14>;
+                    input-enable;
+                    input-schmitt-enable;
+                    slew-rate = <0>;
+                };
+            };
+
+            i2c0_pins_default: i2c0-0 {
+                i2c-pins {
+                    pinmux = <GPIOMUX(62, GPO_LOW,
+                              GPO_I2C0_PAD_SCK_OEN,
+                              GPI_I2C0_PAD_SCK_IN)>,
+                             <GPIOMUX(61, GPO_LOW,
+                              GPO_I2C0_PAD_SDA_OEN,
+                              GPI_I2C0_PAD_SDA_IN)>;
+                    bias-disable; /* external pull-up */
+                    input-enable;
+                    input-schmitt-enable;
+                };
+            };
+
+            uart3_pins_default: uart3-0 {
+                rx-pin {
+                    pinmux = <GPIOMUX(13, GPO_LOW, GPO_DISABLE,
+                              GPI_UART3_PAD_SIN)>;
+                    bias-pull-up;
+                    input-enable;
+                    input-schmitt-enable;
+                };
+                tx-pin {
+                    pinmux = <GPIOMUX(14, GPO_UART3_PAD_SOUT,
+                              GPO_ENABLE, GPI_NONE)>;
+                    bias-disable;
+                    input-disable;
+                    input-schmitt-disable;
+                };
+            };
+        };
+
+        gmac {
+            pinctrl-0 = <&gmac_pins_default>;
+            pinctrl-names = "default";
+        };
+
+        i2c0 {
+            pinctrl-0 = <&i2c0_pins_default>;
+            pinctrl-names = "default";
+        };
+
+        uart3 {
+            pinctrl-0 = <&uart3_pins_default>;
+            pinctrl-names = "default";
+        };
+    };
+
+...
-- 
2.33.0




More information about the linux-riscv mailing list