[PATCH v7 0/5] clk: add driver for the SiFive FU740

[Zong Li]

On Fri, May 21, 2021 at 6:34 PM Zong Li <zong.li at sifive.com> wrote:
>
> On Thu, May 20, 2021 at 2:17 AM Geert Uytterhoeven <geert at linux-m68k.org> wrote:
> >
> > Hi Zong,
> >
> > On Wed, May 19, 2021 at 5:55 PM Zong Li <zong.li at sifive.com> wrote:
> > > On Tue, May 11, 2021 at 4:57 PM Yixun Lan <yixun.lan at gmail.com> wrote:
> > > > On Wed, Apr 14, 2021 at 2:25 PM Zong Li <zong.li at sifive.com> wrote:
> > > > > On Mon, Apr 12, 2021 at 7:31 PM Andreas Schwab <schwab at linux-m68k.org> wrote:
> > > > > > On Mär 31 2021, Zong Li wrote:
> > > > > > > I found that the gemgxlpll was disabled immediately by power
> > > > > > > management after macb driver install. The mainline's defconfig doesn't
> > > > > > > enable CONFIG_PM, so the network is fine on it. The opensuse defconfig
> > > > > > > enables CONFIG_PM, and the patch
> > > > > > > 732374a0b440d9a79c8412f318a25cd37ba6f4e2 added the enable/disable
> > > > > > > callback functions, so the gemgxlpll PLL, I have no idea why power
> > > > > > > management disable it, I would keep trace it.
> > > > > >
> > > > > > Does that mean that CONFIG_PM also affects the FU740?
> > > > >
> > > > > Yes, we got the same problem on the FU740. We are checking the issue.
> > > > >
> > > > Just a mild ping, any progress regarding this issue?
> > >
> > > Currently, if runtime power management is enabled, macb driver would
> > > go to sleep at the end of macb_probe, then the gigabit ethernet PLL
> > > would be disabled.  During this period of time, the system would hang
> > > up if we try to access GEMGXL control registers, it means that we
> > > can't access GEMGXL control registers before the gigabit ethernet PLL
> > > is resumed again. There are some cases, for example, if we execute the
> >
> > Sounds familiar.
> >
> > > 'ifconfig' command, it would eventually go to the macb_get_status to
> >
> > Do you mean mac_get_stats()? macb_get_status() does not exist.
>
> Sorry for the typo, it should be macb_get_stats.
>
> >
> > > access GEMGXL control registers and cause the system to hang up. Give
> > > more example here, if we execute 'ip link set lo up & ip addr add
> > > 127.0.0.1/8 dev lo', it would cause the system to hang up, because
> > > these commands would try to query the interfaces and eventually go to
> > > macb_get_status as well. However, if we can resume the gigabit
> > > ethernet PLL first, such as 'ip link set eth0 up' or 'udhcpc', then
> > > everything goes well. I'm trying to figure out if there are some hooks
> > > that we can check the PLL status in the macb driver before it actually
> > > touches the control registers. If anyone has an idea about that,
> > > please feel free to point it out to me, thanks.
> >
> > And you cannot call pm_runtime_get_sync(), as this is called from
> > atomic contect. Other drivers avoid accessing the registers while
> > the device is not up, cfr. e.g. commit 7fa2955ff70ce453 ("sh_eth:
> > Fix sleeping function called from invalid context").
> >
>
> Thanks for your help. I have done the similar modification by
> following the patch you provided. I also verified the bug that we use
> pm_runtime_get_sync there. I'm going to post the fix patch by adding
> the is_opened flag.
>
> Thanks again.

I have posted a patch to fix this problem. Many thanks to all in this thread.

https://lore.kernel.org/netdev/20210521124859.101012-1-zong.li@sifive.com/T/#u

>
> > Gr{oetje,eeting}s,
> >
> >                         Geert
> >
> > --
> > Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
> >
> > In personal conversations with technical people, I call myself a hacker. But
> > when I'm talking to journalists I just say "programmer" or something like that.
> >                                 -- Linus Torvalds