[PATCH v7 0/5] clk: add driver for the SiFive FU740

[Zong Li]

On Thu, Mar 25, 2021 at 5:22 PM Andreas Schwab <schwab at linux-m68k.org> wrote:
>
> On Mär 25 2021, Zong Li wrote:
>
> > take a look at this again. Could you also let me know which bootloader
> > you used (FSBL or U-boot-SPL)? Thanks.
>
> U-Boot SPL
>
> Please try this image:
>
> http://download.opensuse.org/ports/riscv/tumbleweed/images/openSUSE-Tumbleweed-RISC-V-JeOS-hifiveunleashed.riscv64.raw.xz
>

Hi Andreas,

The following is the result of the test so far. I would continue to
see what happened there.

1. Boot on openSUSE-Tumbleweed-RISC-V-JeOS-hifiveunleashed.riscv64.raw.xz
w/ plugging ethernet cable
  - It seems that I encountered a different situation with you, my
system hung up and I didn't see the boot message you mentioned yet.

[  OK  ] Finished Generate issue file for login session.
[  OK  ] Finished Apply settings from /etc/sysconfig/keyboard.
[  OK  ] Started User Login Management.
[  *** ] (3 of 3) A start job is running for…upplicant service (58s / 1min 51s)
[**    ] (3 of 3) A start job is running for…cant service (1min 28s / 1min 51s)
[   ***] (2 of 3) A start job is running for…cant service (1min 58s / 3min 21s)
[   ***] (1 of 3) A start job is running for…cant service (2min 28s / 3min 21s)
[**    ] (3 of 3) A start job is running for…cant service (2min 58s / 3min 21s)
[ ***  ] (2 of 3) A start job is running for…cant service (3min 28s / 4min 51s)
[     *] (1 of 3) A start job is running for…cant service (3min 58s / 4min 51s)
[ ***  ] (3 of 3) A start job is running for…cant service (4min 28s / 4min 51s)
[***   ] (2 of 3) A start job is running for…cant service (4min 59s / 6min 22s)
[    **] (1 of 3) A start job is running for…cant service (5min 29s / 6min 22s)
[  *** ] (3 of 3) A start job is running for…cant service (5min 59s / 6min 22s)
[*     ] (2 of 3) A start job is running for…cant service (6min 29s / 7min 52s)
[  *** ] (1 of 3) A start job is running for…cant service (6min 59s / 7min 52s)
[    **] (3 of 3) A start job is running for…cant service (7min 29s / 7min 52s)
[FAILED] Failed to start wicked AutoIPv4 supplicant service.
See 'systemctl status wickedd-auto4.service' for details.
[FAILED] Failed to start wicked DHCPv4 supplicant service.
See 'systemctl status wickedd-dhcp4.service' for details.
[FAILED] Failed to start wicked DHCPv6 supplicant service.
See 'systemctl status wickedd-dhcp6.service' for details.
         Starting wicked network management service daemon...
[    **] A start job is running for wicked n…rvice daemon (7min 59s / 9min 22s)
[***   ] A start job is running for wicked n…rvice daemon (8min 29s / 9min 22s)
[  603.364988] BUG: workqueue lockup - pool cpus=1 node=0 flags=0x0
nice=0 stuck for 36s!
[***   ] A start job is running for wicked n…rvice daemon (8min 59s / 9min 22s)
[  633.444986] BUG: workqueue lockup - pool cpus=1 node=0 flags=0x0
nice=0 stuck for 66s!
         Stopping Flush Journal to Persistent Storage...
[  OK  ] Stopped Flush Journal to Persistent Storage.
[  OK  ] Stopped Journal Service.


2. Boot on kernel image which built by opensuse defconfig with
changing CONFIG_MACB to y instead of m
 - Although I got some problem for mounting the root filesystem on
this image now, but I didn't hang up at the message you mentioned, I
could go through after macb driver initialization

[    2.350309] libphy: Fixed MDIO Bus: probed
[    2.354476] macb 10090000.ethernet: Registered clk switch
'sifive-gemgxl-mgmt'
[    2.358752] macb 10090000.ethernet: GEM doesn't support hardware ptp.
[    2.361464] libphy: MACB_mii_bus: probed
[    2.366289] macb 10090000.ethernet eth0: Cadence GEM rev 0x10070109
at 0x10090000 irq 16 (70:b3:d5:92:f2:6c)
[    2.375570] e1000e: Intel(R) PRO/1000 Network Driver
[    2.380323] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    2.386338] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
...
[    2.687447] Waiting for root device /dev/mmcblk0p4...

3. I check the patch set of supporting fu740, it shouldn't impact
fu540, I'm going to dump and comparing the prci content and give more
testing.


> Andreas.
>
> --
> Andreas Schwab, schwab at linux-m68k.org
> GPG Key fingerprint = 7578 EB47 D4E5 4D69 2510  2552 DF73 E780 A9DA AEC1
> "And now for something completely different."