[RFC PATH 2/2] gpio: starfive-jh7100: Add StarFive JH7100 GPIO driver

Michael Walle michael at walle.cc
Mon Jul 26 00:21:31 PDT 2021


Hi Drew, Hi Linus,

Am 2021-07-26 09:11, schrieb Drew Fustini:
> On Fri, Jul 23, 2021 at 11:04:41PM +0200, Linus Walleij wrote:
>> On Thu, Jul 1, 2021 at 8:39 AM Michael Walle <michael at walle.cc> wrote:
>> > Am 2021-07-01 02:20, schrieb Drew Fustini:
>> > > Add GPIO driver for the StarFive JH7100 SoC [1] used on the
>> > > BeagleV Starlight JH7100 board [2].
>> > >
>> > > [1] https://github.com/starfive-tech/beaglev_doc/
>> > > [2] https://github.com/beagleboard/beaglev-starlight
>> > >
>> > > Signed-off-by: Emil Renner Berthing <kernel at esmil.dk>
>> > > Signed-off-by: Huan Feng <huan.feng at starfivetech.com>
>> > > Signed-off-by: Drew Fustini <drew at beagleboard.org>
>> >
>> > Could this driver use GPIO_REGMAP and REGMAP_IRQ? See
>> > drivers/gpio/gpio-sl28cpld.c for an example.
>> 
>> To me it looks just memory-mapped?
>> 
>> Good old gpio-mmio.c (select GPIO_GENERIC) should
>> suffice I think.

But that doesn't mean gpio-regmap can't be used, no? Or what are
the advantages of gpio-mmio?

>> Drew please look at drivers/gpio/gpio-ftgpio010.c for an example
>> of GPIO_GENERIC calling bgpio_init() in probe().
> 
> Thank you for the suggestion. However, I am not sure that will work for
> this SoC.
> 
> The GPIO registers are described in section 12 of JH7100 datasheet [1]
> and I don't think they fit the expectation of gpio-mmio.c because there
> is a seperate register for each GPIO line for output data value and
> output enable.
> 
> There are 64 output data config registers which are 4 bytes wide. There
> are 64 output enable config registers which are 4 bytes wide too. 
> Output
> data and output enable registers for a given GPIO pad are contiguous.
> GPIO0_DOUT_CFG is 0x50 and GPIO0_DOEN_CFG is 0x54 while GPIO1_DOUT_CFG
> is 0x58 and GPIO1_DOEN_CFG is 0x5C. The stride between GPIO pads is
> effectively 8, which yields the formula: GPIOn_DOUT_CFG is 0x50+8n.
> Similarly, GPIO0_DOEN_CFG is 0x54 and thus GPIOn_DOEN_CFG is 0x54+8n.
> 
> However, GPIO input data does use just one bit for each line. GPIODIN_0
> at 0x48 covers GPIO[31:0] and GPIODIN_1 at 0x4c covers GPIO[63:32].

I'd say, that should work with the .reg_mask_xlate of the gpio-regmap.

-michael

> Thus the input could work with gpio-mmio but I am not sure how to
> reconcile the register-per-gpio for the output value and output enable.
> 
> Is there way a way to adapt gpio-mmio for this situation?
> 
> Thanks,
> Drew
> 
> [1] https://github.com/starfive-tech/beaglev_doc



More information about the linux-riscv mailing list