[RFC PATCH 2/3] RISC-V: Initial DTS for Microchip ICICLE board
Ben Dooks
ben.dooks at codethink.co.uk
Thu Oct 29 06:24:03 EDT 2020
On 28/10/2020 23:27, Atish Patra wrote:
> Add initial DTS for Microchip ICICLE board having only
> essential devcies (clocks, sdhci, ethernet, serial, etc).
>
> Signed-off-by: Atish Patra <atish.patra at wdc.com>
> ---
> arch/riscv/boot/dts/Makefile | 1 +
> arch/riscv/boot/dts/microchip/Makefile | 2 +
> .../microchip/microchip-icicle-kit-a000.dts | 313 ++++++++++++++++++
> 3 files changed, 316 insertions(+)
> create mode 100644 arch/riscv/boot/dts/microchip/Makefile
> create mode 100644 arch/riscv/boot/dts/microchip/microchip-icicle-kit-a000.dts
>
> diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
> index ca1f8cbd78c0..3ea94ea0a18a 100644
> --- a/arch/riscv/boot/dts/Makefile
> +++ b/arch/riscv/boot/dts/Makefile
> @@ -1,5 +1,6 @@
> # SPDX-License-Identifier: GPL-2.0
> subdir-y += sifive
> subdir-y += kendryte
> +subdir-y += microchip
>
> obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y))
> diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
> new file mode 100644
> index 000000000000..55ad77521304
> --- /dev/null
> +++ b/arch/riscv/boot/dts/microchip/Makefile
> @@ -0,0 +1,2 @@
> +# SPDX-License-Identifier: GPL-2.0
> +dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-icicle-kit-a000.dtb
> diff --git a/arch/riscv/boot/dts/microchip/microchip-icicle-kit-a000.dts b/arch/riscv/boot/dts/microchip/microchip-icicle-kit-a000.dts
> new file mode 100644
> index 000000000000..5848920af55c
> --- /dev/null
> +++ b/arch/riscv/boot/dts/microchip/microchip-icicle-kit-a000.dts
> @@ -0,0 +1,313 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/* Copyright (c) 2020 Microchip Technology Inc */
> +
> +/dts-v1/;
> +
> +/* Clock frequency (in Hz) of the rtcclk */
> +#define RTCCLK_FREQ 1000000
> +
> +/ {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + model = "Microchip PolarFire-SoC";
> + compatible = "microchip,polarfire-soc";
> +
> + chosen {
> + stdout-path = &serial0;
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + timebase-frequency = <RTCCLK_FREQ>;
> +
> + cpu at 0 {
> + clock-frequency = <0>;
> + compatible = "sifive,rocket0", "riscv";
> + device_type = "cpu";
> + i-cache-block-size = <64>;
> + i-cache-sets = <128>;
> + i-cache-size = <16384>;
> + reg = <0>;
> + riscv,isa = "rv64imac";
> + status = "disabled";
> +
> + cpu0_intc: interrupt-controller {
> + #interrupt-cells = <1>;
> + compatible = "riscv,cpu-intc";
> + interrupt-controller;
> + };
> + };
> +
> + cpu at 1 {
> + clock-frequency = <0>;
> + compatible = "sifive,rocket0", "riscv";
> + d-cache-block-size = <64>;
> + d-cache-sets = <64>;
> + d-cache-size = <32768>;
> + d-tlb-sets = <1>;
> + d-tlb-size = <32>;
> + device_type = "cpu";
> + i-cache-block-size = <64>;
> + i-cache-sets = <64>;
> + i-cache-size = <32768>;
> + i-tlb-sets = <1>;
> + i-tlb-size = <32>;
> + mmu-type = "riscv,sv39";
> + reg = <1>;
> + riscv,isa = "rv64imafdc";
> + tlb-split;
> + status = "okay";
> +
> + cpu1_intc: interrupt-controller {
> + #interrupt-cells = <1>;
> + compatible = "riscv,cpu-intc";
> + interrupt-controller;
> + };
> + };
> +
> + cpu at 2 {
> + clock-frequency = <0>;
> + compatible = "sifive,rocket0", "riscv";
> + d-cache-block-size = <64>;
> + d-cache-sets = <64>;
> + d-cache-size = <32768>;
> + d-tlb-sets = <1>;
> + d-tlb-size = <32>;
> + device_type = "cpu";
> + i-cache-block-size = <64>;
> + i-cache-sets = <64>;
> + i-cache-size = <32768>;
> + i-tlb-sets = <1>;
> + i-tlb-size = <32>;
> + mmu-type = "riscv,sv39";
> + reg = <2>;
> + riscv,isa = "rv64imafdc";
> + tlb-split;
> + status = "okay";
> +
> + cpu2_intc: interrupt-controller {
> + #interrupt-cells = <1>;
> + compatible = "riscv,cpu-intc";
> + interrupt-controller;
> + };
> + };
> +
> + cpu at 3 {
> + clock-frequency = <0>;
> + compatible = "sifive,rocket0", "riscv";
> + d-cache-block-size = <64>;
> + d-cache-sets = <64>;
> + d-cache-size = <32768>;
> + d-tlb-sets = <1>;
> + d-tlb-size = <32>;
> + device_type = "cpu";
> + i-cache-block-size = <64>;
> + i-cache-sets = <64>;
> + i-cache-size = <32768>;
> + i-tlb-sets = <1>;
> + i-tlb-size = <32>;
> + mmu-type = "riscv,sv39";
> + reg = <3>;
> + riscv,isa = "rv64imafdc";
> + tlb-split;
> + status = "okay";
> +
> + cpu3_intc: interrupt-controller {
> + #interrupt-cells = <1>;
> + compatible = "riscv,cpu-intc";
> + interrupt-controller;
> + };
> + };
> +
> + cpu at 4 {
> + clock-frequency = <0>;
> + compatible = "sifive,rocket0", "riscv";
> + d-cache-block-size = <64>;
> + d-cache-sets = <64>;
> + d-cache-size = <32768>;
> + d-tlb-sets = <1>;
> + d-tlb-size = <32>;
> + device_type = "cpu";
> + i-cache-block-size = <64>;
> + i-cache-sets = <64>;
> + i-cache-size = <32768>;
> + i-tlb-sets = <1>;
> + i-tlb-size = <32>;
> + mmu-type = "riscv,sv39";
> + reg = <4>;
> + riscv,isa = "rv64imafdc";
> + tlb-split;
> + status = "okay";
> + cpu4_intc: interrupt-controller {
> + #interrupt-cells = <1>;
> + compatible = "riscv,cpu-intc";
> + interrupt-controller;
> + };
> + };
> + };
> +
> + memory at 80000000 {
> + device_type = "memory";
> + reg = <0x0 0x80000000 0x0 0x40000000>;
> + clocks = <&clkcfg 26>;
> + };
U-boot doesn't seem to be updating this properly.
The board should have 2GiB, confirmed by looking at the device's
chip markings. We only see 1GiB memory. The 0x80000000 bus window
is only capable of dealing with 1GiB memory. The higher 64-bit one
can have 16GiB mapped.
Do we need a second node for the second GiB of memory?
> +
> + soc {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + compatible = "simple-bus";
> + ranges;
> +
> + cache-controller at 2010000 {
> + compatible = "sifive,fu540-c000-ccache", "cache";
> + cache-block-size = <64>;
> + cache-level = <2>;
> + cache-sets = <1024>;
> + cache-size = <2097152>;
> + cache-unified;
> + interrupt-parent = <&plic>;
> + interrupts = <1 2 3>;
> + reg = <0x0 0x2010000 0x0 0x1000>;
> + };
> +
> + clint at 2000000 {
> + compatible = "riscv,clint0";
> + reg = <0x0 0x2000000 0x0 0xC000>;
> + interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
> + &cpu1_intc 3 &cpu1_intc 7
> + &cpu2_intc 3 &cpu2_intc 7
> + &cpu3_intc 3 &cpu3_intc 7
> + &cpu4_intc 3 &cpu4_intc 7>;
> + };
> +
> + plic: interrupt-controller at c000000 {
> + #interrupt-cells = <1>;
> + compatible = "sifive,plic-1.0.0";
> + reg = <0x0 0xc000000 0x0 0x4000000>;
> + riscv,ndev = <53>;
> + interrupt-controller;
> + interrupts-extended = <&cpu0_intc 11
> + &cpu1_intc 11 &cpu1_intc 9
> + &cpu2_intc 11 &cpu2_intc 9
> + &cpu3_intc 11 &cpu3_intc 9
> + &cpu4_intc 11 &cpu4_intc 9>;
> + };
> +
> + dma at 3000000 {
> + compatible = "sifive,fu540-c000-pdma";
> + reg = <0x0 0x3000000 0x0 0x8000>;
> + interrupt-parent = <&plic>;
> + interrupts = <23 24 25 26 27 28 29 30>;
> + #dma-cells = <1>;
> + };
> +
> + refclk: refclk {
> + compatible = "fixed-clock";
> + #clock-cells = <0>;
> + clock-frequency = <600000000>;
> + clock-output-names = "msspllclk";
> + };
> +
> + clkcfg: clkcfg at 20002000 {
> + compatible = "microchip,pfsoc-clkcfg";
> + reg = <0x0 0x20002000 0x0 0x1000>;
> + reg-names = "mss_sysreg";
> + clocks = <&refclk>;
> + #clock-cells = <1>;
> + clock-output-names = "cpuclk", "axiclk", "ahbclk", "ENVMclk", "MAC0clk", "MAC1clk", "MMCclk", "TIMERclk", "MMUART0clk", "MMUART1clk", "MMUART2clk", "MMUART3clk", "MMUART4clk", "SPI0clk", "SPI1clk", "I2C0clk", "I2C1clk", "CAN0clk", "CAN1clk", "USBclk", "RESERVED", "RTCclk", "QSPIclk", "GPIO0clk", "GPIO1clk", "GPIO2clk", "DDRCclk", "FIC0clk", "FIC1clk", "FIC2clk", "FIC3clk", "ATHENAclk", "CFMclk";
Any chance of making this list multi-line, it is difficult to read as-is.
> + };
> +
> + serial0: serial at 20000000 {
> + compatible = "ns16550a";
> + reg = <0x0 0x20000000 0x0 0x400>;
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + interrupt-parent = <&plic>;
> + interrupts = <90>;
> + current-speed = <115200>;
> + clocks = <&clkcfg 8>;
> + status = "okay";
> + };
> +
> + serial1: serial at 20100000 {
> + compatible = "ns16550a";
> + reg = <0x0 0x20100000 0x0 0x400>;
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + interrupt-parent = <&plic>;
> + interrupts = <91>;
> + current-speed = <115200>;
> + clocks = <&clkcfg 9>;
> + status = "okay";
> + };
> +
> + serial2: serial at 20102000 {
> + compatible = "ns16550a";
> + reg = <0x0 0x20102000 0x0 0x400>;
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + interrupt-parent = <&plic>;
> + interrupts = <92>;
> + current-speed = <115200>;
> + clocks = <&clkcfg 10>;
> + status = "okay";
> + };
> +
> + serial3: serial at 20104000 {
> + compatible = "ns16550a";
> + reg = <0x0 0x20104000 0x0 0x400>;
> + reg-io-width = <4>;
> + reg-shift = <2>;
> + interrupt-parent = <&plic>;
> + interrupts = <93>;
> + current-speed = <115200>;
> + clocks = <&clkcfg 11>;
> + status = "okay";
> + };
> +
> + sdcard: sdhc at 20008000 {
> + compatible = "cdns,sd4hc";
> + reg = <0x0 0x20008000 0x0 0x1000>;
> + interrupt-parent = <&plic>;
> + interrupts = <88>;
> + pinctrl-names = "default";
> + clocks = <&clkcfg 6>;
> + bus-width = <4>;
> + disable-wp;
> + no-1-8-v;
> + cap-mmc-highspeed;
> + cap-sd-highspeed;
> + card-detect-delay = <200>;
> + sd-uhs-sdr12;
> + sd-uhs-sdr25;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + max-frequency = <200000000>;
> + status = "okay";
> + };
Given eMMC is the default device, shouldn't that be default for the
device tree too? Even if not, having the emmc node here would be a
good thing as it is different to the SD node.
> +
> + emac1: ethernet at 20112000 {
> + compatible = "cdns,macb";
> + reg = <0x0 0x20112000 0x0 0x2000>;
> + interrupt-parent = <&plic>;
> + interrupts = <70 71 72 73>;
> + mac-address = [56 34 12 00 FC 00];
> + phy-mode = "sgmii";
> + clocks = <&clkcfg 5>, <&clkcfg 2>;
> + clock-names = "pclk", "hclk";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + phy1: ethernet-phy at 9 {
> + reg = <9>;
> + ti,fifo-depth = <0x01>;
> + };
> + };
Aren't there two ethernet ports on the board?
Also, at the moment u-boot is not filling the MAC address parameter
in so we've got at two boards on the network with the same MAC until
we override it in the device tree for the second.
> +
> + uio_axi_lsram at 2030000000 {
> + compatible = "generic-uio";
> + reg = <0x20 0x30000000 0 0x80000000 >;
> + status = "okay";
> + };
> + };
> +};
>
--
Ben Dooks http://www.codethink.co.uk/
Senior Engineer Codethink - Providing Genius
https://www.codethink.co.uk/privacy.html
More information about the linux-riscv
mailing list