[PATCH v3 1/1] i2c: ocores: fix polling mode workaround on FU540-C000 SoC

[Peter Korsgaard]

>>>>> "Sagar" == Sagar Shrikant Kadam <sagar.kadam at sifive.com> writes:

 > The FU540-C000 has a broken IRQ and support was added earlier
 > so that it will operate in polling mode, but seems to work only
 > in case interrupts property is missing from the i2c0 dt-node.
 > This should not be the case and the driver should handle polling
 > mode with the interrupt property present in i2c0 node of the
 > device tree.
 > So check if it's the FU540-C000 soc and enable polling mode master
 > xfers, as the IRQ for this chip is broken.

 > Fixes commit c45d4ba86731 ("i2c: ocores: add polling mode workaround
 > for Sifive FU540-C000 SoC")

 > Signed-off-by: Sagar Shrikant Kadam <sagar.kadam at sifive.com>
 > ---
 >  drivers/i2c/busses/i2c-ocores.c | 22 +++++++++++++---------
 >  1 file changed, 13 insertions(+), 9 deletions(-)

 > diff --git a/drivers/i2c/busses/i2c-ocores.c b/drivers/i2c/busses/i2c-ocores.c
 > index f5fc75b..1dab02d 100644
 > --- a/drivers/i2c/busses/i2c-ocores.c
 > +++ b/drivers/i2c/busses/i2c-ocores.c
 > @@ -686,17 +686,21 @@ static int ocores_i2c_probe(struct platform_device *pdev)
 
 >  	init_waitqueue_head(&i2c->wait);
 
 > +	/*
 > +	 * Set OCORES_FLAG_BROKEN_IRQ to enable workaround for
 > +	 * FU540-C000 SoC in polling mode.
 > +	 * Since the SoC does have interrupt its dt has the interrupt
 > +	 * defined but it should be bypassed in driver as this SoC has

NIT: Looks like there some commas missing and the wording sounds a bit
odd to me. What about E.G.:

     /*
      * Since the SoC does have an interrupt, its DT has an interrupt
      * property - But this should be bypassed as the IRQ logic in this
      * SoC is broken.
      */

 > +	 * a broken IRQ, hence update the master_xfer to use polling
 > +	 * transfers.
 > +	 */
 > +	if (of_device_is_compatible(pdev->dev.of_node,
 > +				    "sifive,fu540-c000-i2c"))
 > +		i2c->flags |= OCORES_FLAG_BROKEN_IRQ;
 > +
 >  	irq = platform_get_irq(pdev, 0);
 > -	if (irq == -ENXIO) {
 > +	if (i2c->flags & OCORES_FLAG_BROKEN_IRQ || irq == -ENXIO) {


Alternatively you can move it after the irq = platform_get_irq(pdev, 0)
line and just clear irq, E.G.:

irq = platform_get_irq(pdev, 0);

if (of_device_is_compatible(..)) {
   i2c->flags |= OCORES_FLAG_BROKEN_IRQ;
   irq = -ENXIO;
}

if (irq == -ENXIO) {
..

-- 
Bye, Peter Korsgaard