[PATCH v14 00/18] KVM RISC-V Support
Anup Patel
anup.patel at wdc.com
Mon Aug 31 08:25:20 EDT 2020
This series adds initial KVM RISC-V support. Currently, we are able to boot
Linux on RV64/RV32 Guest with multiple VCPUs.
Key aspects of KVM RISC-V added by this series are:
1. No RISC-V specific KVM IOCTL
2. Minimal possible KVM world-switch which touches only GPRs and few CSRs
3. Both RV64 and RV32 host supported
4. Full Guest/VM switch is done via vcpu_get/vcpu_put infrastructure
5. KVM ONE_REG interface for VCPU register access from user-space
6. PLIC emulation is done in user-space
7. Timer and IPI emuation is done in-kernel
8. Both Sv39x4 and Sv48x4 supported for RV64 host
9. MMU notifiers supported
10. Generic dirtylog supported
11. FP lazy save/restore supported
12. SBI v0.1 emulation for KVM Guest available
13. Forward unhandled SBI calls to KVM userspace
14. Hugepage support for Guest/VM
15. IOEVENTFD support for Vhost
Here's a brief TODO list which we will work upon after this series:
1. SBI v0.2 emulation in-kernel
2. SBI v0.2 hart state management emulation in-kernel
3. In-kernel PLIC emulation
4. ..... and more .....
This series can be found in riscv_kvm_v14 branch at:
https//github.com/avpatel/linux.git
Our work-in-progress KVMTOOL RISC-V port can be found in riscv_v4 branch
at: https//github.com/avpatel/kvmtool.git
The QEMU RISC-V hypervisor emulation is done by Alistair and is available
in mainline/anup/riscv-hyp-ext-v0.6.1 branch at:
https://github.com/kvm-riscv/qemu.git
To play around with KVM RISC-V, refer KVM RISC-V wiki at:
https://github.com/kvm-riscv/howto/wiki
https://github.com/kvm-riscv/howto/wiki/KVM-RISCV64-on-QEMU
https://github.com/kvm-riscv/howto/wiki/KVM-RISCV64-on-Spike
Changes since v13:
- Rebased on Linux-5.9-rc3
- Fixed kvm_riscv_vcpu_set_reg_csr() for SIP updation in PATCH5
- Fixed instruction length computation in PATCH7
- Added ioeventfd support in PATCH7
- Ensure HSTATUS.SPVP is set to correct value before using HLV/HSV
intructions in PATCH7
- Fixed stage2_map_page() to set PTE 'A' and 'D' bits correctly
in PATCH10
- Added stage2 dirty page logging in PATCH10
- Allow KVM user-space to SET/GET SCOUNTER CSR in PATCH5
- Save/restore SCOUNTEREN in PATCH6
- Reduced quite a few instructions for __kvm_riscv_switch_to() by
using CSR swap instruction in PATCH6
- Detect and use Sv48x4 when available in PATCH10
Changes since v12:
- Rebased patches on Linux-5.8-rc4
- By default enable all counters in HCOUNTEREN
- RISC-V H-Extension v0.6.1 spec support
Changes since v11:
- Rebased patches on Linux-5.7-rc3
- Fixed typo in typecast of stage2_map_size define
- Introduced struct kvm_cpu_trap to represent trap details and
use it as function parameter wherever applicable
- Pass memslot to kvm_riscv_stage2_map() for supporing dirty page
logging in future
- RISC-V H-Extension v0.6 spec support
- Send-out first three patches as separate series so that it can
be taken by Palmer for Linux RISC-V
Changes since v10:
- Rebased patches on Linux-5.6-rc5
- Reduce RISCV_ISA_EXT_MAX from 256 to 64
- Separate PATCH for removing N-extension related defines
- Added comments as requested by Palmer
- Fixed HIDELEG CSR programming
Changes since v9:
- Rebased patches on Linux-5.5-rc3
- Squash PATCH19 and PATCH20 into PATCH5
- Squash PATCH18 into PATCH11
- Squash PATCH17 into PATCH16
- Added ONE_REG interface for VCPU timer in PATCH13
- Use HTIMEDELTA for VCPU timer in PATCH13
- Updated KVM RISC-V mailing list in MAINTAINERS entry
- Update KVM kconfig option to depend on RISCV_SBI and MMU
- Check for SBI v0.2 and SBI v0.2 RFENCE extension at boot-time
- Use SBI v0.2 RFENCE extension in VMID implementation
- Use SBI v0.2 RFENCE extension in Stage2 MMU implementation
- Use SBI v0.2 RFENCE extension in SBI implementation
- Moved to RISC-V Hypervisor v0.5 draft spec
- Updated Documentation/virt/kvm/api.txt for timer ONE_REG interface
Changes since v8:
- Rebased series on Linux-5.4-rc3 and Atish's SBI v0.2 patches
- Use HRTIMER_MODE_REL instead of HRTIMER_MODE_ABS in timer emulation
- Fixed kvm_riscv_stage2_map() to handle hugepages
- Added patch to forward unhandled SBI calls to user-space
- Added patch for iterative/recursive stage2 page table programming
- Added patch to remove per-CPU vsip_shadow variable
- Added patch to fix race-condition in kvm_riscv_vcpu_sync_interrupts()
Changes since v7:
- Rebased series on Linux-5.4-rc1 and Atish's SBI v0.2 patches
- Removed PATCH1, PATCH3, and PATCH20 because these already merged
- Use kernel doc style comments for ISA bitmap functions
- Don't parse X, Y, and Z extension in riscv_fill_hwcap() because it will
be added in-future
- Mark KVM RISC-V kconfig option as EXPERIMENTAL
- Typo fix in commit description of PATCH6 of v7 series
- Use separate structs for CORE and CSR registers of ONE_REG interface
- Explicitly include asm/sbi.h in kvm/vcpu_sbi.c
- Removed implicit switch-case fall-through in kvm_riscv_vcpu_exit()
- No need to set VSSTATUS.MXR bit in kvm_riscv_vcpu_unpriv_read()
- Removed register for instruction length in kvm_riscv_vcpu_unpriv_read()
- Added defines for checking/decoding instruction length
- Added separate patch to forward unhandled SBI calls to userspace tool
Changes since v6:
- Rebased patches on Linux-5.3-rc7
- Added "return_handled" in struct kvm_mmio_decode to ensure that
kvm_riscv_vcpu_mmio_return() updates SEPC only once
- Removed trap_stval parameter from kvm_riscv_vcpu_unpriv_read()
- Updated git repo URL in MAINTAINERS entry
Changes since v5:
- Renamed KVM_REG_RISCV_CONFIG_TIMEBASE register to
KVM_REG_RISCV_CONFIG_TBFREQ register in ONE_REG interface
- Update SPEC in kvm_riscv_vcpu_mmio_return() for MMIO exits
- Use switch case instead of illegal instruction opcode table for simplicity
- Improve comments in stage2_remote_tlb_flush() for a potential remote TLB
flush optimization
- Handle all unsupported SBI calls in default case of
kvm_riscv_vcpu_sbi_ecall() function
- Fixed kvm_riscv_vcpu_sync_interrupts() for software interrupts
- Improved unprivilege reads to handle traps due to Guest stage1 page table
- Added separate patch to document RISC-V specific things in
Documentation/virt/kvm/api.txt
Changes since v4:
- Rebased patches on Linux-5.3-rc5
- Added Paolo's Acked-by and Reviewed-by
- Updated mailing list in MAINTAINERS entry
Changes since v3:
- Moved patch for ISA bitmap from KVM prep series to this series
- Make vsip_shadow as run-time percpu variable instead of compile-time
- Flush Guest TLBs on all Host CPUs whenever we run-out of VMIDs
Changes since v2:
- Removed references of KVM_REQ_IRQ_PENDING from all patches
- Use kvm->srcu within in-kernel KVM run loop
- Added percpu vsip_shadow to track last value programmed in VSIP CSR
- Added comments about irqs_pending and irqs_pending_mask
- Used kvm_arch_vcpu_runnable() in-place-of kvm_riscv_vcpu_has_interrupt()
in system_opcode_insn()
- Removed unwanted smp_wmb() in kvm_riscv_stage2_vmid_update()
- Use kvm_flush_remote_tlbs() in kvm_riscv_stage2_vmid_update()
- Use READ_ONCE() in kvm_riscv_stage2_update_hgatp() for vmid
Changes since v1:
- Fixed compile errors in building KVM RISC-V as module
- Removed unused kvm_riscv_halt_guest() and kvm_riscv_resume_guest()
- Set KVM_CAP_SYNC_MMU capability only after MMU notifiers are implemented
- Made vmid_version as unsigned long instead of atomic
- Renamed KVM_REQ_UPDATE_PGTBL to KVM_REQ_UPDATE_HGATP
- Renamed kvm_riscv_stage2_update_pgtbl() to kvm_riscv_stage2_update_hgatp()
- Configure HIDELEG and HEDELEG in kvm_arch_hardware_enable()
- Updated ONE_REG interface for CSR access to user-space
- Removed irqs_pending_lock and use atomic bitops instead
- Added separate patch for FP ONE_REG interface
- Added separate patch for updating MAINTAINERS file
Anup Patel (14):
RISC-V: Add hypervisor extension related CSR defines
RISC-V: Add initial skeletal KVM support
RISC-V: KVM: Implement VCPU create, init and destroy functions
RISC-V: KVM: Implement VCPU interrupts and requests handling
RISC-V: KVM: Implement KVM_GET_ONE_REG/KVM_SET_ONE_REG ioctls
RISC-V: KVM: Implement VCPU world-switch
RISC-V: KVM: Handle MMIO exits for VCPU
RISC-V: KVM: Handle WFI exits for VCPU
RISC-V: KVM: Implement VMID allocator
RISC-V: KVM: Implement stage2 page table programming
RISC-V: KVM: Implement MMU notifiers
RISC-V: KVM: Document RISC-V specific parts of KVM API
RISC-V: KVM: Add MAINTAINERS entry
RISC-V: Enable KVM for RV64 and RV32
Atish Patra (4):
RISC-V: KVM: Add timer functionality
RISC-V: KVM: FP lazy save/restore
RISC-V: KVM: Implement ONE REG interface for FP registers
RISC-V: KVM: Add SBI v0.1 support
Documentation/virt/kvm/api.rst | 193 ++++-
MAINTAINERS | 11 +
arch/riscv/Kconfig | 2 +
arch/riscv/Makefile | 2 +
arch/riscv/configs/defconfig | 3 +
arch/riscv/configs/rv32_defconfig | 3 +
arch/riscv/include/asm/csr.h | 89 ++
arch/riscv/include/asm/kvm_host.h | 278 +++++++
arch/riscv/include/asm/kvm_types.h | 7 +
arch/riscv/include/asm/kvm_vcpu_timer.h | 44 +
arch/riscv/include/asm/pgtable-bits.h | 1 +
arch/riscv/include/uapi/asm/kvm.h | 128 +++
arch/riscv/kernel/asm-offsets.c | 156 ++++
arch/riscv/kvm/Kconfig | 36 +
arch/riscv/kvm/Makefile | 15 +
arch/riscv/kvm/main.c | 118 +++
arch/riscv/kvm/mmu.c | 857 +++++++++++++++++++
arch/riscv/kvm/tlb.S | 74 ++
arch/riscv/kvm/vcpu.c | 1012 +++++++++++++++++++++++
arch/riscv/kvm/vcpu_exit.c | 701 ++++++++++++++++
arch/riscv/kvm/vcpu_sbi.c | 173 ++++
arch/riscv/kvm/vcpu_switch.S | 400 +++++++++
arch/riscv/kvm/vcpu_timer.c | 225 +++++
arch/riscv/kvm/vm.c | 81 ++
arch/riscv/kvm/vmid.c | 120 +++
drivers/clocksource/timer-riscv.c | 8 +
include/clocksource/timer-riscv.h | 16 +
include/uapi/linux/kvm.h | 8 +
28 files changed, 4752 insertions(+), 9 deletions(-)
create mode 100644 arch/riscv/include/asm/kvm_host.h
create mode 100644 arch/riscv/include/asm/kvm_types.h
create mode 100644 arch/riscv/include/asm/kvm_vcpu_timer.h
create mode 100644 arch/riscv/include/uapi/asm/kvm.h
create mode 100644 arch/riscv/kvm/Kconfig
create mode 100644 arch/riscv/kvm/Makefile
create mode 100644 arch/riscv/kvm/main.c
create mode 100644 arch/riscv/kvm/mmu.c
create mode 100644 arch/riscv/kvm/tlb.S
create mode 100644 arch/riscv/kvm/vcpu.c
create mode 100644 arch/riscv/kvm/vcpu_exit.c
create mode 100644 arch/riscv/kvm/vcpu_sbi.c
create mode 100644 arch/riscv/kvm/vcpu_switch.S
create mode 100644 arch/riscv/kvm/vcpu_timer.c
create mode 100644 arch/riscv/kvm/vm.c
create mode 100644 arch/riscv/kvm/vmid.c
create mode 100644 include/clocksource/timer-riscv.h
--
2.25.1
More information about the linux-riscv
mailing list