[PATCH] Extract initrd free logic from arch-specific code.

[Russell King - ARM Linux]

On Thu, Mar 29, 2018 at 05:43:47PM +0200, Geert Uytterhoeven wrote:
> On Thu, Mar 29, 2018 at 5:27 PM, Russell King - ARM Linux
> <linux at armlinux.org.uk> wrote:
> > On Thu, Mar 29, 2018 at 09:37:52AM +1100, Oliver wrote:
> >> On Thu, Mar 29, 2018 at 9:14 AM, Russell King - ARM Linux
> >> <linux at armlinux.org.uk> wrote:
> >> > On Wed, Mar 28, 2018 at 02:04:22PM -0500, Rob Landley wrote:
> >> >> On 03/28/2018 11:48 AM, Russell King - ARM Linux wrote:
> >> >> > On Wed, Mar 28, 2018 at 10:58:51AM -0500, Rob Landley wrote:
> >> >> >> On 03/28/2018 10:26 AM, Shea Levy wrote:
> >> >> >>> Now only those architectures that have custom initrd free requirements
> >> >> >>> need to define free_initrd_mem.
> >> >> >> ...
> >> >> >>> --- a/arch/arc/mm/init.c
> >> >> >>> +++ b/arch/arc/mm/init.c
> >> >> >>> @@ -229,10 +229,3 @@ void __ref free_initmem(void)
> >> >> >>>  {
> >> >> >>>   free_initmem_default(-1);
> >> >> >>>  }
> >> >> >>> -
> >> >> >>> -#ifdef CONFIG_BLK_DEV_INITRD
> >> >> >>> -void __init free_initrd_mem(unsigned long start, unsigned long end)
> >> >> >>> -{
> >> >> >>> - free_reserved_area((void *)start, (void *)end, -1, "initrd");
> >> >> >>> -}
> >> >> >>> -#endif
> >> >> >>> diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
> >> >> >>> index 3f972e83909b..19d1c5594e2d 100644
> >> >> >>> --- a/arch/arm/Kconfig
> >> >> >>> +++ b/arch/arm/Kconfig
> >> >> >>> @@ -47,6 +47,7 @@ config ARM
> >> >> >>>   select HARDIRQS_SW_RESEND
> >> >> >>>   select HAVE_ARCH_AUDITSYSCALL if (AEABI && !OABI_COMPAT)
> >> >> >>>   select HAVE_ARCH_BITREVERSE if (CPU_32v7M || CPU_32v7) && !CPU_32v6
> >> >> >>> + select HAVE_ARCH_FREE_INITRD_MEM
> >> >> >>>   select HAVE_ARCH_JUMP_LABEL if !XIP_KERNEL && !CPU_ENDIAN_BE32 && MMU
> >> >> >>>   select HAVE_ARCH_KGDB if !CPU_ENDIAN_BE32 && MMU
> >> >> >>>   select HAVE_ARCH_MMAP_RND_BITS if MMU
> >> >> >>
> >> >> >> Isn't this why weak symbols were invented?
> >> >> >
> >> >> > Weak symbols means that we end up with both the weakly-referenced code
> >> >> > and the arch code in the kernel image.  That's fine if the weak code
> >> >> > is small.
> >> >>
> >> >> The kernel's been able to build with link time garbage collection since 2016:
> >> >>
> >> >> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=b67067f1176d
> >> >>
> >> >> Wouldn't that remove the unused one?
> >> >
> >> > Probably, if anyone bothered to use that, which they don't.
> >> >
> >> > LD_DEAD_CODE_DATA_ELIMINATION is a symbol without a prompt, and from
> >> > what I can see, nothing selects it.  Therefore, the symbol is always
> >> > disabled, and so the feature never gets used in mainline kernels.
> >> >
> >> > Brings up the obvious question - why is it there if it's completely
> >> > unused?  (Maybe to cause confusion, and allowing a justification
> >> > for __weak ?)
> >>
> >> IIRC Nick had some patches to do the arch enablement for powerpc, but
> >> I'm not sure what happened to them though. I suspect it just fell down
> >> Nick's ever growing TODO list.
> >
> > I've given it a go on ARM, marking every linker-built table with KEEP()
> > and comparing the System.map files.  The resulting kernel is around
> > 150k smaller, which seems good.
> >
> > However, it doesn't boot - and I don't know why.  Booting the kernel
> > under kvmtool in a VM using virtio-console, I can find no way to get
> > any kernel messages out of it.  Using lkvm debug, I can see that the
> > PC is stuck inside die(), and that's the only information I have.
> > It dies before bringing up the other CPUs, so it's a very early death.
> >
> > I don't think other console types are available under ARM64.
> 
> earlycon?

Through what - as I say above, I think the only thing that's present is
virtio-console, and the virtio stack only get initialised much later in
boot.

Eg, there's the memory-based virtio driver which interfaces any virtio
driver to a memory-based ring structures for communication with the host
(drivers/virtio/virtio_mmio.c) which is initialised at module_init()
time, and so isn't available for earlycon.

I don't think merely changing the module_init() calls in the appropriate
virtio bits will suffice - it's why I pointed out that it dies before
SMP initialisation, which also means that it dies before we start
running the initcalls for subsystems and drivers.

I'm not aware of there being an emulated UART in the guest's address
space, so serial based stuff doesn't work.

-- 
RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 8.8Mbps down 630kbps up
According to speedtest.net: 8.21Mbps down 510kbps up